Advertisement
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 2
Model #8100X
Model #8100X Outside Safety Ladder
Ladder must be attached to pool frame - DO NOT USE with inflatable pools
If missing parts call - Toll free U.S./Canada - 800-635-3213 or www.conferladders.com
ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY
Parts List
2 - Ladder Legs
2 - Tread Connector
Parts List
4 - Swing up Treads
2 - Ladder Legs
1 - Standard Tread
2 - Tread Connectors
2 - Extension Boots
4 - Swing up Treads
1 - Platform
2 - Handrails
1 - Standard Tread
2 - Adjustable Tube Handrails
2 - Extension Boots
1 - Platform
Hardware Pack
2 - Handrails
14 - #10 x 1-1/4" screws
2 - Adjustable Tube Handrails
2 - Plugs (wg)
2 - 1/4 - 20 x 2" Bolts
Hardware Pack
2 - 1/4 - 20 Acorn Nuts
14 - #10 x 1-1/4" screws
2 - Adjustable Tubes
2 - Plugs (wg)
2 - Mounting Blocks
2 - 1/4 - 20 x 2" Bolts
4 - 1/4 - 20 x 2-1/4" Bolts
2 - 1/4 - 20 Acorn Nuts
4 - 1/4 - Flat Washers
2 - Adjustable Tubes
8 - 1/4 - 20 Hex Nuts
2 - Mounting Blocks
4 - 1/4 - 20 x 1" Bolts
4 - 1/4 - 20 x 2 1/4" Bolts
1 - Padlock
4 - 1/4 - Flat Washers
8 - 1/4 - 20 Hex Nuts
4 - 1/4 - 20 x 1" Bolts
1 - Padlock
If missing parts call - Toll free U.S. - 800-635-3213 or www.Conferplastics.com
1.
LAK KIT
Place (2) two ladder legs on a flat
Check building codes/permitting. Consult your local Building Department before installation of your pool and
surface. Using a Phillips screwdriv-
equipment. Pool/equipment installation must comply with the codes of the authority having jurisdiction and may require
er tap out the plastic film from the
permits (e.g., building, plumbing, electrical, zoning, etc.).
three holes on the bottom of
Use for intended purpose only
each leg.
• Use only as a swimming pool ladder.
• This ladder is designed and manufactured for a specific pool wall height and/or deck of the pool - check product
specification and the height of your pool.
Check that you have all required parts. Check the contents of the carton with the Parts List for this ladder. All parts and
hardware are required. If any parts are missing, DO NOT attempt to assemble or install the ladder. Instead, call Toll
Free U.S. - 800-635-3213 or visit our web site at www.conferladders.com for assistance.
Select an appropriate location - The ladder must be located on a level, solid base and in a location that will be in full
view of competent adult supervision when in use.
Follow all instructions
• For stable, correct assembly and installation, all instructions must be followed completely and in the sequence shown.
• Follow the manufacturer's recommendations for the safe use of all hand tools and equipment used during installation.
Cordless drill only - no corded drills near pool. Use a cordless drill for assembly and installation. To reduce the risk of
electrocution, NEVER use a corded drill in or around a pool.
Using two 1/4-20 x 2" long bolts and
two acorn nuts fasten the extension
Lift safely. When lifting awkward or heavy loads, have another person help you.
boots to the ladder legs
Double check after installation
2
• Before using the product, after assembly and installation, go over the instructions and procedures again to make sure
nothing has been overlooked.
• Make sure that safety labels are installed and legible.
2
Outside Safety Ladder
ADJUSTABLE
TUBE
HANDRAILS
ADJUSTABLE
TUBES
MOUNTING
BLOCKS
PLATFORM
LADDER
LEGS
EXTENSION
BOOT
For Use with Confer Plastics In-Pool Step
IMPORTANT: LADDER ADAPTER KIT
2.
LAK kit fits Confer A-frame ladders for use with non-traditional
metal framed swimming pools with a wall height of 48" - 54".
Use with models: 7100b, 7100x, 7000b, 7200 and 7000x.
Not for use with inflatable pools.
Safe Installation
To reduce the risk of electrocution, drowning, entrapment, falls, or other serious
injury or death:
Extension boots are not required if
the outside height of your pool
(measured from the ground to the
top of the pool ledge) is 48" or less.
If this measurement is more than
48" extension boots will be
required. Using a Phillips screwdriver
4.
tap out the plastic film from the top
hole on each side of the extension
boots.
Tools Needed for Assembly
HANDRAIL
* - Rubber mallet
Needed for Assembly
* - Adjustable wrench
- Rubber mallet
* - Cordless Drill
- Phillips screwdriver
* - 5/16" Drill Bit
- Adjustable wrench
* - Phillips Screwdriver
- Liquid soap or lubricant
or screwdriver bits
- Cordless Drill / Phillips Driver
TREAD
* - Pliers
- 5/16" Drill bit
CONNECTIORS
* - Liquid soap or lubricant
SWING UP
TREAD
Use a little liquid soap to
help with ladder assembly.
STANDARD
TREAD
3.
Slip the (2) two extension boots over
the ends of the ladder legs. They will
need to be all the way on if the
outside dimension is 52" and backed
off one hole if the outside dimension
is 54".
Slide (4) four of the swing up treads
over the ladder legs as shown.
S
t
t
t
e
S
l
A
b
5.
S
t
t
Advertisement
