Table of Contents
Advertisement
The rnachine is of Ihe attcnded type, and must be installed in
places where it can be monitored by trained personnel.
Warning: it is forbidden lo install Ihe machine in a place where
lit may be reached, touched and/or operatod by persons other
than those specified in sectlon"J.2. ■ Authorized persons".
The machirie may only opsrate in places wilh an ambient lemperature ranging
beiweart 10aC (50°F) and 32X. (89.6'F).
5.1. Accessories supplied
■
Pipe deaner: for correct cleamng of Ihe hol chocolale dispensing Channel
5.2. Installation-Positioning
It is necessary to check ihe following:
•
Ihe sile has been duly prepared for machine Installation;
•
(hat the premises are suitably wall lil. aired. clean and hygienrc, and thal [he
power sockel is within easy reach:
•
Ihe surface Die machine will be inslalled on is firm, flai and solid;
■
that Ihe machine is placed at least 20 cm (7 8 incties) from the edge ot Ihe
top used.
Adeguate clearance must be Icft around the machine lo onable
| \ personnel to work wilhout any conslraints and also to leave the
work area immedlately in case of need.
Fig, 5 shows Ihe mimmum clearaiices for inslallaiiori.
Note: Leave a 25 cm (10 inches) space in the Lipper part.
\
N
\
25cm
|
10 inchesr
\
N
\
150 cm
60 inches
Fig. 5
Flg. 5 shows Ihe clearances required for access:
•
IhD controls siiuaied on Ihe lefl sitle;
•
machine parts so thal they may be servicod in Ute evem of a fault.
Important note: when lifting the machlne, do not use the prod-
uet dispenser unit (tap), drainaga pipe. water fevel indicator
Iray, bowl hooft on handles or Ihe bowl itseff: grip the boltom
machine body. Any damage to ihe machlne deriving (rom fail-
uie \o follow these rules will nol bo covered by the v/arranty.
After positionmg Ihe pagking Container in Ihe vicmily of Ihe inslallalion sile. pro-
cesd as follows;
• open Ihe front part of ihe packing conlainer.
• tift the machine and remove it from ils packing.
• Ihen Position il on Ihe prepared sile.
I Before the machine is operaled the firsl Urne, ils components must
1 1 be ihoroughly cleaned; for furthor details sgb me relevant section
herein.
5.3. Disposal of packing materials
Aller opening the box. niake sure to separate the packing malsrials according
!o type arid dtspose of fliem in aecordance wilJl Ihe cuneni tegulalions in the
user's CGLJiury.
We recommend keeping the box for futuia eunveyance or transport.
5.4. Electrical connection
This Job may be performed only by specialized technical per
sonnel.
efore inserling Ihe plug inio the mains power sockel. make sure lhat
ihe line uoltage used is tfie same as the value indicaied on the manufactur-
er's raUng plate;
Ihe main swilch is sei to -OFF-.
t( Ihe niachiiifi is being connecled to the elednaty manis for the firsl lime. Ihis
Operation musi be performed by a specialized techriician, while the Custoiner
will be rasponsible for and have lo lake care of any subsequani cannections.
The machine musi be connecled to ihe eleclricity mains by means of the plug
fi tted an Ihe power cofd. Be sure lo comply wilh.
• the technical regulaticns and Standards in lorce at the time of Installation;
■
the tiata shcjvn on the rating plate on the side of ihe macfiine.
Watnlng: the electric outiel must be situated In a piace easily
wilhirt reach of the user. so thst no effort is required in Order
to disconnect Ihe machine from Ihe power supply when neces
sary.
If tha power cord is damaged, you must have it replaced either by the
manufactureroraspecialiiedlochnician.
®
It is forbidden:
to use extension cords of any type;
•
to replace the original plug;
to use adaptors.
SL3200OI846Ed.O2- 11/2007
- 7_GB -
Advertisement
Table of Contents
