Helmholz 700-850-4PS01 Quick Start Manual
Profinet-switch 4/8/16-port
Hide thumbs
Also See for 700-850-4PS01:
- Quick start manual (20 pages) ,
- Manual (43 pages) ,
- Quick start manual (10 pages)
Subscribe to Our Youtube Channel
Related Manuals for Helmholz 700-850-4PS01
Summary of Contents for Helmholz 700-850-4PS01
- Page 1 Quick Start Guide PROFINET-Switch 4/8/16-port Version as of FW 1.08 www.helmholz.com...
-
Page 2: Table Of Contents
Contents 1. Safety instructions 2. Introduction 3. Preparing the PROFINET-Switch 4. Planning of the GSDML files 5. Setting the port properties 6. Topology detection 7. Assign the PROFINET-Switch a name 8. Media Redundancy Protocol (MRP) 9. Diagnosis and configuration via the web interface 10. -
Page 3: Safety Instructions
1. Safety instructions Target audience This description is only intended for trained personnel qualified in control and auto- mation engineering who are familiar with the applicable national standards. For installation, commissioning, and operation of the components, compliance with the instructions and explanations in this operating manual is essential. The specialist person- nel is to ensure that the application or the use of the products described fulfills all safety requirements, including all applicable laws, regulations, provisions, and standards. -
Page 4: Introduction
This Quick Start Guide explains the basic settings for the initial commissioning of PROFI- P1 — P4: NET-Switches for use in a PROFINET project. For PROFINET devices or other You can find further information in the manual. You can find this under www.helmholz.de Ethernet devices or scan the QR code directly. SCAN FCN:... -
Page 5: Preparing The Profinet-Switch
The RJ45 sockets “P1 – P4” (4-port switch), “P1 – P8” (8-port switch) and “P1 – P16” (16-port switch) serve the connection of the network participants (PROFINET or Ethernet). 3.2 Install GSDML file Please download the GSDML file under www.helmholz.de or scan the QR code. SCAN QR CODE... -
Page 6: Planning Of The Gsdml Files
Following installation, the PROFINET-Switch can be found in the hardware catalog under “Other field devices g PROFINET IO g Network Components g Helmholz GmbH & Co. KG g Helmholz PN switch”. Add the “PROFINET-Switch, 4-port”, “PROFINET-Switch 8-port” of “PROFINET-Switch, 16-port” device to the project and connect it with your PROFINET network. -
Page 7: Setting The Port Properties
5. Setting the port properties Each port of the PROFINET-Switch can be individually configured. Transfer medium/duplex: “Activate” The port can be switched off here. This option is recommended when the port shouldn’t be used. Unauthorized trespass into the network is prevented. -
Page 8: Assign The Profinet-Switch A Name
The MAC address of the device can be found on the device front of the PROFINET-Switch. The Helmholz IPSet tool, which can be downloaded at no charge from the Helmholz website, can also be used to set the PROFINET name. -
Page 9: Media Redundancy Protocol (Mrp)
8. Media Redundancy Protocol (MRP) The PROFINET-Switch supports the optional media redundancy protocol (MRP) as MRP client. MRP enables ring wiring, which also makes operation of the PROFINET network possible in the event of the failure of a cable or of a participant. There must be at least one MRP master (e.g. -
Page 10: Diagnosis And Configuration Via The Web Interface
9. Diagnosis and configuration via the web interface The web interface is also accessible under the IP address assigned to the PROFINET-Switch in the PROFINET network. When the web interface is first called up, the password of the “admin” user is the serial number of the device. The serial number is indicated on the right housing side part (e.g. - Page 11 One goes to the system view following entry of the new password: Note: If the PROFINET-Switch is configured and used in a PROFINET network, settings in the web interface are only to be viewed as a diagnosis. A reconfiguration of PROFINET-related settings (Port Status, LLDP, DCP, Ring Redundancy) is then not possible in the web interface. Quick Start Guide PROFINET-Switch 4/8/16-port...
-
Page 12: Switch Diagnosis And Settings
10. Switch diagnosis and settings Extensive information and settings for the function of the switch are accessible in the Switch menu. 11. Port mirroring In order to be able to carry out frame analyses or recordings, Port Mirroring can be activated in the PROFINET-Switch. With Port Mirroring, the frame transfer from one “mirrored port”... -
Page 13: Statistics
12. Statistics Detailed statistics on the data transfer can be queried in the “Statistics” menu. Among other things, the quality of the transmission can be monitored in the sub-menu “Statistics by Error”. Quick Start Guide PROFINET-Switch 4/8/16-port... -
Page 14: Agents
13. Agents In order to already be able to view basic information about the switch at the start website, before or without having logged in, the option “System Status Without Login” can be selected. With “Web Session Timeout”, it can be established whether an automatic logout should take place in the event of inactivity at the website for security reasons. Quick Start Guide PROFINET-Switch 4/8/16-port... -
Page 15: Snmp
14. SNMP The PROFINET-Switch supports SNMP (“Simple Network Management Protocol”) in order to also enable the identification and diagnosis of the switch for IT administration tools. Quick Start Guide PROFINET-Switch 4/8/16-port... -
Page 16: Setting The Time
15. Setting the time The PROFINET-Switch contains a system clock for the issuing of logs and alarm messages. This can be set either manually or automatically by an SNTP server. Quick Start Guide PROFINET-Switch 4/8/16-port... -
Page 17: Resetting To Factory Settings
17. Firmware update A firmware update can be carried out via the web interface. Please download the firmware update file under www.helmholz.de or The firmware update file can be selected in the menu “System g Firmware”. scan the QR code. -
Page 18: Led Status Information
18. LED status information 19. Button functions The PROFINET-Switch can be reset to factory settings No power supply or device defective with the “FCN” button. Device is correctly supplied with voltage If the “FCN” button is pressed during the run-up time of the switch, the orange “SF”... -
Page 19: Technical Data
20. Technical data PROFINET-Switch, 4-port, managed PROFINET-Switch, 8-port, managed PROFINET-Switch, 16-port, managed 700-850-4PS01 700-850-8PS01 700-850-16P01 Dimensions (D x W x H) 32 x 59 x 76 mm 32 x 82 x 76 mm 32 x 146 x 76 mm Weight Approx. - Page 20 Our customers are at the center of everything we do. We welcome all ideas and suggestions. Helmholz GmbH & Co. KG | Hannberger Weg 2 | 91091 Großenseebach | Germany | Phone +49 9135 7380-0 | Fax +49 9135 7380-110 | info@helmholz.de | www.helmholz.com...
Need help?
Do you have a question about the 700-850-4PS01 and is the answer not in the manual?
Questions and answers