Advertisement
Quick Links
Advertisement
Related Manuals for Supermicro SYS-221BT-DNTR
Summary of Contents for Supermicro SYS-221BT-DNTR
- Page 1 WEEE DISASSEMBLY INSTRUCTIONS SUPERMICRO SYS-221BT-DNTR ENCLOSURE Abstract This document provides clear guidance for end-of-life recyclers on how to identify and disassemble reportable materials in compliance with the Waste Electrical and Electronic Equipment (WEEE) directive.
-
Page 2: Table Of Contents
Table of Contents Product Views ............................1 Reportable Materials on SYS-221BT-DNTR ....................3 Disassemble Instructions .......................... 4 3.3 Step-by-Step Disassembly Instructions ....................7 Removing Cable and Chassis Top Cover ..................7 Removing Hard Disk Drive (HDDD) / Solid State Drive (SDD) ............8 Removing Power Supply ....................... -
Page 3: Product Views
1. Product Views Front view Rear view Product construct view Hard Disk Drive/ Solid State Drive Node B Node A Power Supply... -
Page 5: Reportable Materials On Sys-221Bt-Dntr
2. Reportable Materials on SYS-221BT-DNTR According to Article 8(2) and Annex VII of WEEE directive 2012/19/EU, below materials and components should be selectively treated. Description Notes Quantity Printed Circuit Boards (PCB) or With a surface greater than 10 sq cm 2.4,3.5,4.2,5.1, 7.3, 8.2,... -
Page 6: Disassemble Instructions
3. Disassemble Instructions The intent of this document is to provide guidance to recyclers on the presence of materials and components at the product / family level, as required by the EU WEEE Directive 2012/10/EU. This document should also help direct recyclers to proper methods for removing parts and general product disassembly instructions. - Page 7 Chassis Backplane Air Shroud *2 Sponge Screw, Stand-off Motherboard Storage Controller Card Storage Controller Card Riser Card*2 Cable Battery...
- Page 8 Power Supply Power Enclosure*2 Screw and Standoff*2 Set Power Supply Module*2 Power Distributor*1 Storage Card and CPU Heat Sink *4Set Processor* 2Set SSD * 4set AIOM *4 DIMM *4Set Power Cable M.2 *8 Hard Drive * 8...
-
Page 9: Step-By-Step Disassembly Instructions
3.3 Step-by-Step Disassembly Instructions 1. Removing Cable and Chassis Top Cover 1. Use the operating system to power down the system. 2. After the system has completely shutdown, disconnect the power cords from the power supply modules. 3. Remove all cables/ unit from the server IO port. 4. -
Page 10: Removing Hard Disk Drive (Hddd) / Solid State Drive (Sdd)
2. Removing Hard Disk Drive (HDDD) / Solid State Drive (SDD) 1. Push the release button on the drive carrier, which will extend the drive bay handle 2. Use the drive bay handle to pull the drive carrier out of the chassis 3. -
Page 11: Removing Power Supply
6. Use a cross screwdriver to remove screws and lift off the PCB Description Dummy Tray HDD/ SSD Hard Drive Enclosure Hard Drive PCB 3. Removing Power Supply 1. Press the release tab on the failed power supply. 2. Use the handle to gently slide the power supply out the back of the chassis. 3. -
Page 12: Removing Power Distributor
4. Cut the power leads connected to the fan and lift the main board from the chassis Description Power Supply Power Enclosure Fan Cable Power Module PCB Capacitor 4. Removing Power Distributor 1. Disconnect the power cords from the power supply modules. Remove 4 screws and lift out the power distributor from the chassis 3. -
Page 13: Removing Backplane
Remove screw and standoff Description Power Distributor Power Distributor PCB 5. Removing Backplane 1. Remove the backplane 8 screws from the chassis Description Backplane 6. Removing Fan 1. Remove the fan cable from the backplane for the failed fan and the adjacent fan. 2. -
Page 14: Removing Aiom Card
Description Cooling Fan Fan Housing 7. Removing AIOM Card 1. Press the node holder, then hold the node and pull the node from the chassis 2. Press the release tab and loosen the thumbscrew on the AIOM card 3. Grasp the release tab and the thumbscrew and pull the AIOM out of the node tray 4. -
Page 15: Removing The Air Shroud, Riser, And The Riser Bracket
Description Node AIOM Card AIOM PCB 8. Removing the Air shroud, Riser, and the Riser Bracket 1. Remove screws each from the air shroud, lift it by hand. 3. Take the riser card and bracket away from the chassis Removing the screw from riser card. Removing the screw from riser bracket. -
Page 16: Removing Processor
9. Removing Processor 1. Removing the PHM (Processor Heatsink Module ) from the motherboard, first shut down the system and unplug the AC power cord from all power supplies 2. Use a T30-bit screwdriver to loosen the four peek nuts on the heatsink in the sequence of A, B, C, and D 3. -
Page 17: Removing Dimm
6. When all plastic clips have been detached from the heatsink, remove the processor carrier assembly from the heatsink 7. Unlock the lever from its locked position and push it upwards to disengage the processor from the processor carrier, as shown below right 8. -
Page 18: Removing Storage Controller Card And M.2
1. Hand press both release tabs on the ends of the DIMM module to unlock it 2. Once the DIMM module is loose, remove it from the memory slot Description 10.1 DIMM 11. Removing Storage Controller Card and M.2 11.1 1. -
Page 19: Removing Control Panel
12.2 12.1 Description 12.1 Motherboard 12.2 Battery Note: Repeat steps 1-12 of each node(A,B,C,D) disassembled, then the chassis enclosure can be recycled 13. Removing Control Panel Remove control panel screw (R and L) from chassis... - Page 20 13.1 13.2 Remove backet screw and hand screw (R and L) from control panel and used hand remove backet mylar. Description 13.1 Control Panel Cover L & R 13.2 MYLAR_L & R...
Need help?
Do you have a question about the SYS-221BT-DNTR and is the answer not in the manual?
Questions and answers