Download Print this page

Sealey SD800.V2 Instructions page 2

Variable speed

Advertisement

Risk of hand Arm Vibration Injury
Variable speed Hammer drills sd800.V2 & sd1000.V2. When operated in accordance with these instructions and tested in accordance with
en 28662-1: 1993 results in the following vibration emission declared in accordance with Bs en12096: 1996.
measured vibration emission value: . . . . . .(sd800) 1.91m/s
uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . .(sd800) 0.76m/s
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended measures to reduce risk of hand-arm vibration syndrome:
this item represents a low Hand Arm Vibration risk to users. the calculated maximum usage period exceeds 8 hours. We recommend
appropriate safety equipment is utilised and regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive
strain injury.
2. TEChNICAL SPECIFICATIONS
mODEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD800.V2 . .
Input power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 50Hz . .
motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 810W . .
speed at no load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 3000rpm . .
chuck capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 - 13mm . .
Hammer action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-28000bpm . .
drilling capacity for steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm . .
maximum capacity for wood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25mm . .
maximum capacity for concrete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm . .
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.4kg . .
sound pressure level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.4dB(A) . .
sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102.4dB(A) . .
Vibration level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.91m/s
6
5
8
7
fig.1
SD800
3. OPERATING INSTRUCTIONS
3.1.
PREPARING DRILL FOR USE.
3.1.1. ensure the drill is switched off and unplugged from the mains power supply.
3.1.2. Fitting the side handle. fit supplementary handle grip by placing the handle assembly over chuck head and onto the machine neck.
secure by rotating the handle clockwise until it is tight and the handle can no longer be moved. to ensure a good grip in all
circumstances the angle of the handle may be changed by rotating the handle grip anti-clockwise until the handle assemble is loose.
rotate the handle to the desired angle and retighten.
3.1.3
Fitting the depth gauge. to fit the depth gauge loosen the side handle and pass the gauge through the handle clamp to the required
depth. rotate the handle to the required angle. As the handle is tightened the depth gauge will also be gripped firmly.
3.2.
DRILL CONTROLS
3.2.1. ON/OFF Variable speed trigger. Your drill has a variable speed control on/off trigger, which increases the speed the more the trigger
is depressed.
3.2.2. Trigger lock. to lock 'on', depress the trigger, push in and hold the button then release the trigger. release the lock on button and
your drill will continue running accordingly.
3.2.3. to release the lock depress the trigger and release it.
3.2.4. Power failure. If you have the lock on feature engaged during use and your drill becomes disconnected from the power supply,
disengage the lock on feature immediately.
WARNING! Before connecting your drill to power supply, ensure it is not in the lock on position as this may result in
damage and personal injury. Depress the trigger to ensure release. DO NOT use the lock on facility for jobs where your drill
may need to be stopped suddenly.
3.2.5. maximum speed setting control. the variable speed trigger has a small rotating knob incorporated into it, which can be used to
control the maximum speed of the drill. When the knob is set to the maximum or + setting the trigger can be fully depressed allowing
the drill to turn at its maximum speed. As the knob is turned towards the minimum or - setting the movement of the trigger is restricted
so that the drill will turn at a lower pre-set speed when the trigger is fully depressed. this facility is useful when working with materials
that should be drilled at a constant, lower speed.
3.2.6. Two speed gearbox (SD1000 only). the sd1000 also incorporates a 2 speed mechanical gearbox which used in conjunction with
the other speed controls adds additional versatility to this model. to select the lower speed turn the gear selector knob so that '1' is
adjacent to the arrow on the casing. to select the higher speed turn the gear selector knob so that '2' is adjacent to the arrow on the
casing. It may be necessary to rotate the chuck by hand slightly whilst using the gear selector in order to get the gears to mesh.
1. trigger lock button
2. on/off trigger
3. forward/reverse
selector
1
4. Variable speed knob
5. chuck
6. drill/impact selector
3
7. side handle
8. depth gauge
4
9. chuck key
2
10. High/low gear knob
(sd1000 only)
9
,
Original Language Version
(sd1000) 1.73m/s
2
2
(sd1000) 0.69m/s
2
2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD1000.V2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 50Hz
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050W
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 1100 / 0 - 3000rpm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 - 13mm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 10000 / 0 - 27000bpm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16mm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3kg
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92.7dB(A)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.7dB(A)
2
. .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.73m/s
5
8
7
fig.2
6
3
4
10
SD1000
sd800.V2 & sd1000.V2
2
1
2
9
Issue no.1 27/07/10

Advertisement

loading

This manual is also suitable for:

Sd1000.v2