Sealey SD750.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. ELECTRICAL SAFETY
 WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all
electrical products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fi tted with the
correct fuse - see fuse rating in these instructions.
 DO NOT pull or carry the appliance by the power cable.
 DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a fi rm grip on the plug.
 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualifi ed electrician.
1.1.4. This product is fi tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualifi ed electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
 DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualifi ed electrician.
1.2. GENERAL SAFETY
 Disconnect the hammer drill from the mains power before changing accessories, servicing or performing any maintenance.
Maintain the hammer drill in good condition.

 Check moving parts and alignment and keep drill bits in good, sharp condition. If necessary use an authorised service agent.
 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
 DO NOT use the hammer drill if the on/off switch does not work. Have it repaired by an authorised service agent.
 Wear approved safety eye protection with side shields, ear defenders, safety shoes and gloves.
 Wear ear defenders when impact drilling. Exposure to noise can cause hearing loss.
 Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
 Use the hammer drill in an adequate working area for its function, keep work area clean, tidy and free from unrelated materials, ensure
adequate lighting.
 Prevent body contact with grounded surfaces to avoid electric shock i.e. pipes, radiators, ranges, refrigerators etc.
 Evaluate your working area before using the hammer drill i.e. ceiling, floors and enclosures may contain hidden electrical wires or water
piping.
Maintain correct balance and footing.

 DO NOT over-reach and ensure that the floor is not slippery and wear non skid safety shoes.
 WARNING! If working at height take adequate safety precautions to prevent injury from falling.
 DO NOT operate the hammer drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 WARNING! The auxiliary handle grip must always be attached for use. Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
 WARNING! Remove the chuck key before turning the hammer drill on.
 DO NOT attempt to operate this hammer drill with one hand.
© Jack Sealey Limited
Ø13MM VARIABLE SPEED HAMMER DRILL
750W
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
SD750.V2
Keep in dry area Wear a mask
protect from rain
Warning:
Electricity shock
hazard
Recommended fuse rating
13 Amp
SD750.V2 Issue 1 24/03/22