Download Print this page
Sealey SDM30.V2 Instructions

Sealey SDM30.V2 Instructions

5-speed hobby pillar drill 580mm ht 350w

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
Instruction
protection
Manual
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the drill is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information: it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
8
immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING! Disconnect drill from mains power before changing accessories, servicing or performing any maintenance.
Maintain the drill in good condition (use an authorised service agent).
9
WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
A guard, or any other part, that is damaged should be repaired/replaced before the tool is used, to ensure that it will operate
properly and perform its intended function. The safety guard is a mandatory fitting where drill is used in premises covered by
the Health & Safety at Work Act.
Check alignment of moving parts and check for possible broken parts.
9
Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and will invalidate the
9
warranty.
Ensure the set screws of the head frame are tight before using the drill.
9
Secure the drill to a supporting structure to avoid the machine tipping, sliding or walking.
9
Drill is designed for use with drill bits only. No other accessory may be used.
9
Ensure the chuck is securely fastened to the spindle.
9
Remove adjusting keys and wrenches from the machine and working area before switching on.
9
Use clamps or a vice (not included) to secure the work piece. Available from your Sealey stockist.
9
DO NOT secure the work piece by hand.
8
Refer to speed chart for recommended drilling speeds.
9
WARNING! Always wear approved eye or face protection when operating this drill. Use a face or dust mask if dust is
generated.
WARNING! DO NOT wear gloves when drilling.
Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
9
Keep the work area as childproof as possible by using padlocks and master switches.
9
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
© Jack Sealey Limited
5-SPEED HOBBY PILLAR DRILL 580MM HT
350W
SDM30.V2
MODEL NO:
Original Language Version
replaced
Recommended fuse rating
5Amp
SDM30.V2 Issue 5 (2,3) 30/06/20

Advertisement

loading

Summary of Contents for Sealey SDM30.V2

  • Page 1 SDM30.V2 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 The safety guard mounting is pre-fitted to the drill head. Remove the three small screws in the guard support channel, insert the guard and refit the screws, through the holes provided in the guard. Note that the guard is in two parts held together by two screws and wing nuts. Original Language Version SDM30.V2 Issue 5 (2,3) 30/06/20 © Jack Sealey Limited...
  • Page 3 When ready to drill, simply pull the feed handle. The drill feed will stop at the set depth. 6.7. GUARD 6.7.1. Always adjust guard length, by loosening wing nut at each side (fig.5.A), to give maximum protection before starting to drill. Fig.4 Fig.5 Original Language Version SDM30.V2 Issue 5 (2,3) 30/06/20 © Jack Sealey Limited...
  • Page 4 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...