Elektra Beckum TKHS 315 E/P Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Elektra Beckum Manuals
  4. Saw
  5. TKHS 315 E/P Series
  6. Operating instructions manual

Elektra Beckum TKHS 315 E/P Operating Instructions Manual

Hide thumbs Also See for TKHS 315 E/P:
Table of Contents

Advertisement

Quick Links

See also: Operating Instructions Manual
A0229IVZ.fm
TKHS 315 E/P
Betriebsanleitung . . . . . . . . . . . . . . . . . . . . 3
Operating Instruction . . . . . . . . . . . . . . . . 15
Instructions d'utilisation . . . . . . . . . . . . . . 26
Manuale d'istruzioni . . . . . . . . . . . . . . . . . 38
Manual de uso . . . . . . . . . . . . . . . . . . . . . 50

Advertisement

Table of Contents
loading

Related Manuals for Elektra Beckum TKHS 315 E/P

Summary of Contents for Elektra Beckum TKHS 315 E/P

  • Page 1 A0229IVZ.fm TKHS 315 E/P Betriebsanleitung ....3 Operating Instruction ....15 Instructions d'utilisation .
  • Page 2 TKHS 315 E/P TKHS 315 E/P TKHS 315 E/P *EN 1870-1, EN 60204 ** 98/37/EG, 89/336/EWG, 73/23/EWG, 93/68/EWG *** BM 9410359 02 **** TÜV-Rheinland, Am Grauen Stein, D-51105 Köln Jürgen Kusserow Vorstand ELEKTRA BECKUM AG – Daimlerstraße 1 – 49716 Meppen 1001028/01...

  • Page 3: Machine Overview

    XA0026E4.fm Operating Instruction ENGLISH ENGLISH 1. Machine overview Swing-out galvanized steel Stand with multiple reinforce- sheet rear table extension ment beads for high stability. Saw blade ∅ 315 mm Mitre fence Rip fence Maintenance-free induction motor Table top of galvanized steel plate –...

  • Page 4: Table Of Contents

    ENGLISH Table of Contents 3. Safety instructions Danger! Risk of electric shock! Do not expose tool to rain. Machine overview .....15 Specified conditions of Do not operate tool in damp or wet envi- Please read first! .......16 ronment. Safety instructions....16 This machine is intended to rip and Prevent body contact with earthed crosscut grown timber, faced boards,...

  • Page 5: Symbols Used Throughout These Instructions

    ENGLISH − cables Drawing-in/trapping hazard! Risk of personal injury by body − wires parts or clothing being drawn Hazard generated by insuffi- into the rotating saw blade. cient personal protection gear! Caution! Wear hearing protection. Risk of material damage. Wear safety glasses. Wear dust mask.

  • Page 6: Assembly

    ENGLISH Setting device for saw blade tilt For use as rip fence the long fence Place table top (24) upside down on extrusion (22) must be installed. It is a stable, level support. Put a layer of With the blade tilt lever (18) the saw mounted on the guide extrusion at cardboard or similar underneath to blade is steplessly tilted from 0°...
  • Page 7 ENGLISH Attach cable with cable tie (32) to Fit table insert extrusion (35) flush the motor carrier unit. into the saw table. Caution! Make sure the cable does not run over sharp edges and is not bent. Riving knife adjustment. Danger! For shipping the riving knife is is lowered beneath the table top's...
  • Page 8 ENGLISH − from the inside screw on flange Table extension installation Adjust the hexagon thin nuts (56) on nuts (49) – do not yet tighten the guide bar until the guide bar is Item Description Qty. fully. exactly parallel with the edge of the Guide bar, long table top.

  • Page 9: Mains Connection

    ENGLISH Attach the other hexagon head Changing the direction of rota- Use personal protection gear: screws likewise to the right-hand tion! (three-phase motors only) − dust respirator; side of the right front leg. Depending phase − hearing protection; sequence, it is possible the −...

  • Page 10: Setting The Depth Of Cut

    ENGLISH Operation without a dust collector is only possible: Note: − outdoors; To compensate for possible play in the blade height setting mechanism, − for short-term operation always raise the blade to the desired (up to a maximum of 30 minutes); position.

  • Page 11: Tips And Tricks

    ENGLISH − Saw blades have to be mounted Caution! The plastic nose must have at in such way that they do not wob- least 10 mm distance to the line of ble or run out of balance and can cut. not work loose during operation.

  • Page 12: Maintenance

    ENGLISH Maintenance Care and Maintenance Spray to Loss of cutting performance remove resin residue and preserve Saw blade blunt (possibly tempering Before switching ON metal surfaces. marks on blade body): Visual check if distance saw blade – riv- Saw blade CV 315 x 1.8 x 30 −...

  • Page 13: Technical Specifications

    ENGLISH 15. Technical specifications TKHS 315 E/P TKHS 315 E/P TKHS 315 E/P TKHS 315 E/P 2.2 W 3.1 W 2.8 D 4.2 D Voltage 230 V / 1~50 Hz 230 V / 1~50 Hz 400 V / 3~50 Hz 400 V / 3~50 Hz Nominal current 10.6...
  • Page 14 U3a0229.fm 091 005 7154 091 005 3680 091 001 4030 091 003 1260 091 101 8691 091 000 0250 091 000 0195 091 001 2282 091 005 3353 091 005 3361 091 005 3345...
  • Page 15 U4BA_EB2.fm...

Table of Contents