Transmitter Memorisation And Deletion Procedures - Nice WIDE S Instructions And Warnings For Installation And Use

7.4.3 Transmitter memorisation and deletion procedures

a
To perform the procedures A, B, C and D described
below, the control unit's memory must be unlocked.
If the memory is locked, perform the unlocking pro-
cedure described in the "LOCKING AND UNLOCK-
ING THE MEMORY" paragraph
43
ON OK
PROG RADIO
7.4.3.1 PROCEDURE A - Memorising ALL buttons of a
single transmitter (STANDARD mode or Mode 1)
To perform this procedure:
1. on the control unit: press and hold the "RADIO" button
until the "R" LED lights up
2.
release the "RADIO" button
3. (within 10 seconds) on the transmitter to be saved: press
and hold any button and wait until the "R" LED emits 3 long
flashes (= transmitter saved correctly)
4. release the transmitter button.
l
After the 3 long flashes a further 10 seconds remain
to memorise an additional transmitter (if desired),
starting from step 3.
l
The "R" LED can also emit the following signals: 1
fast flash, if the transmitter is already saved, 6 flash-
es, if the transmitter's radio encoding system is not
compatible with that of the control unit's receiver,
or 8 flashes, if the memory is full.
7.4.3.2 PROCEDURE B - Memorising a SINGLE BUTTON
of a transmitter (CUSTOM mode or Mode 2)
To perform this procedure:
1.
choose the command to be paired with the relevant button
to be memorised:
– for no. 1 - "Step-by-Step" press the "RADIO" button
once
– for no. 2 - "STOP" press the "RADIO" button twice
– for no. 3 - "OPEN" press the "RADIO" button 3 times
– for no. 4 - "CLOSE" press the "RADIO" button 4 times
2. on the control unit: press and release the "RADIO" button
for a number of times corresponding to the desired control,
as shown near the control selected beforehand at step 1.
3. (within 10 seconds) on the transmitter: press and hold the
button to be saved and wait for the "R" LED to emit 3 long
flashes (= transmitter saved correctly)
4. release the transmitter button.
R
R - Pause +
IBT4N
l
After the 3 long flashes a further 10 seconds remain
to memorise an additional button (if desired), start-
ing from step 1.
l
The "R" LED can also emit the following signals: 1
fast flash, if the transmitter is already saved, 6 flash-
es, if the transmitter's radio encoding system is not
compatible with that of the control unit's receiver,
or 8 flashes, if the memory is full.
7.4.3.3 PROCEDURE C - Memorising a transmitter by
Speed
means of another transmitter already memorised
(memorisation far from the control unit)
This procedure allows to save a new transmitter by means of a
second transmitter already saved in the same control unit. This
allows the new transmitter to receive the same settings as the
transmitter that was already saved. The procedure does not entail
any direct action on the "RADIO" button of the control unit, but its
mere execution within its reception range.
To perform this procedure:
1. on the transmitter to be memorised: press and hold the
button to be memorised
2. on the control unit: after a few seconds (roughly 5) the "R"
LED lights up
3. release the transmitter button
4. on the transmitter already memorised: press and slowly
release 3 times the memorised button to be copied
5. on the transmitter to be saved: press and hold the same
button pressed at step 1 and wait for the "R" LED to emit 3
long flashes (= transmitter saved correctly)
6. release the transmitter button.
l
The "R" LED can also emit the following signals: 1
fast flash, if the transmitter is already saved, 6 flash-
es, if the transmitter's radio encoding system is not
compatible with that of the control unit's receiver,
or 8 flashes, if the memory is full.
7.4.3.4 PROCEDURE D - Deleting a single transmitter
(if memorised in Mode 1) or a single transmitter
button (if memorised in Mode 2)
To perform this procedure:
1. on the control unit: press and hold the "RADIO" button
2.
after roughly 4 seconds, the "R" LED will light up steady
(continue holding down the "RADIO" button)
3. on the transmitter to be deleted: press and hold a button
(*) until the "R" LED (on the control unit) emits 5 fast flashes
(or 1 flash if the transmitter or button is not saved).
4. press and release the "RADIO" button.
(*) If the transmitter is memorised in Mode 1, any button
can be pressed and the control unit will delete the entire
transmitter. If the transmitter is memorised in Mode 2, it is
necessary to press the memorised button to be deleted.
To delete further buttons memorised in Mode 2, repeat the
entire procedure for every button to be deleted.
ENGLISH – 25