Manual Test Mode (Washer) - Whirlpool W11114976B Service Data Sheet

FOR SERVICE TECHNICIAN'S USE ONLY

MANUAL TEST MODE (WASHER)

Manual Load Test
NOTE: The tub must be empty of clothes
and water before running this test.
To activate Manual Load Test, press and
hold CYCLES or CYCLE SELECT, then press
POWER. While continuing to press and hold
CYCLES or CYCLE SELECT, press START
three times. A tone will sound for 1 second
to indicate successful entering of the Manual
Load Test. The "Control Lock" indicator will
be lit and "CL" will appear in the display.
Instructions: Press CYCLES or CYCLE
SELECT to select the Load to test. Press
and hold START to apply power to the Load.
The Load will be powered as long as the
Start button is pressed. Release the
START button to turn off power to the Load.
NOTE: The speaker will beep on and off
as long as the Start button is depressed.
See the chart below.
j
Press
CYCLES
or CYCLE
SELECT
Until
Following Press and
Indicator Hold START
Is Lit: to Initiate:
Normal Clockwise
rotation of
the motor
Delicate Counter-
clockwise
rotation of
the motor
Heavy Activation of
or Heavy the retractor
Duty motor
Rinse Activation
of the cold
water valve
Spin Activation
of the hot
water valve
Clean Activation
Washer of the lid
lock solenoid
(lid will lock)
(Release of
Start will
unlock the lid)
Press POWER to exit the test.
PAGE 10
k
7-Segment
Display
Shows:
Model
Number
Software
version
number
Voltage/
frequency
Size of tub/
up drain
Water level/
frequency
Washer
serial
number
Spin Test
Press POWER to turn on the washer.
Press and hold "+" while pressing START
three times. A tone will sound for 1 second
to indicate successful entering of the Spin Test.
The display will indicate "3" if there is no water
in the tub, "4" if there is water in the tub. The
"Normal" indicator will be flashing. When water
in the tub reaches the "RESET" level, the washer
will start to spin (continuous for 1 minute, off for
1 minute). The washer will then turn off.
If the lid is opened during the spin, the display
will indicate "E4" and the washer will stop
spinning. If the lid is closed again, the washer
will resume spinning. If the tub switch detects
an unbalance during the spin, "E3" will show
on the display and the motor will stop.
Press POWER to clear the error and exit the test.
Lid Switch Test
Press POWER to turn on the washer.
Press and hold CYCLES or CYCLE SELECT
while pressing START three times. A tone will
sound for 1 second to indicate successful
entering of the Lid Switch Test.
The "Normal" indicator will be lit, and the
washer tub will begin to rotate clockwise.
If the lid is opened, the tub will stop; if it is
closed again, the tub will resume rotation.
The tub will not rotate if it contains water.
Press POWER to exit the test.
UI/LED Test
Press POWER to turn on the washer.
Press and hold TEMP or WASH TEMP while
pressing START three times. A tone will sound
for 1 second to indicate successful entering
of the UI/LED Test. The display will indicate
"8.8." and all indicators will be off.
Press "–." The Control Lock and Lid Lock
indicators will be lit. Press "–" again. The
Control Lock and Lid Lock indicators will
turn off.
Press CYCLES or CYCLE SELECT. All of the
Cycle indicators will be lit. Press CYCLES or
CYCLE SELECT again. The Cycle indicators
will turn off.
Press "+." The 7-segment display showing
"8.8." will turn off. Press "+" again. The
7-segment display will turn on.
Press TEMP or WASH TEMP . All of the Temp
indicators will be lit. Press TEMP or WASH
TEMP again. The Temp indicators will turn off.
Press POWER to exit the test.
DO NOT REMOVE OR DESTROY