Table of Contents
Advertisement
Quick Links
VENUE XO16 Analog/Digital
9321-61201-00 REV A 3/09
Output Card
For VENUE Mix Rack and VENUE SC48
Digidesign
2001 Junipero Serra Boulevard
Daly City, CA 94014-3886 USA
tel: 650·731·6300
fax: 650·731·6399
Technical Support (USA)
tel: 650·731·6100
fax: 650·731·6375
Product Information (USA)
tel: 650·731·6102
tel: 800·333·2137
International Offices
Visit the Digidesign Website
for contact information
Website
www.digidesign.com
™
Advertisement
Table of Contents
Related Manuals for DigiDesign VENUE XO16
Summary of Contents for DigiDesign VENUE XO16
- Page 1 VENUE XO16 Analog/Digital Output Card ™ For VENUE Mix Rack and VENUE SC48 Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650·731·6300 fax: 650·731·6399 Technical Support (USA) tel: 650·731·6100 fax: 650·731·6375 Product Information (USA) tel: 650·731·6102 tel: 800·333·2137...
- Page 2 NOTE: This equipment has been tested and found to comply with the limits for a This guide is copyrighted ©2009 by Digidesign, a division of Avid Technology, Inc. Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are (hereafter “Digidesign”), with all rights reserved.
-
Page 3: Table Of Contents
Contents Chapter 1. Overview ................1 XO16 Card Components. - Page 4 XO16 Analog/ Digital Output Card...
-
Page 5: Chapter 1. Overview
Analog Outputs 1-8 AES Digital Outputs 9-16 Figure 1. XO16 Analog/Digital Output Card ® The XO16 Analog/Digital Output Card from Digidesign pro- System Requirements vides eight analog line outputs and four stereo digital outputs to your VENUE Mix Rack or VENUE SC48™ console. -
Page 6: Conventions Used In This Guide
Conventions Used in This Guide All Digidesign guides use the following conventions to indi- cate menu choices and key commands in D-Show and Pro Tools: Convention Action File > Save Session In Pro Tools, choose Save Session from the File menu. -
Page 7: Chapter 2. Installing The Xo16 Card
Chapter 2: Installing the XO16 Card This chapter provides information on installing an XO16 card Remove Mix Rack’s front panel cover by unscrewing its in a Mix Rack or an SC48 console. mounting screws (#1 Phillips). For instructions on installing a card in a Mix Rack, see “Install- Mounting screws (remove all) ing an XO16 Card in Mix Rack”... - Page 8 On Mix Rack’s back panel, locate output slot E. Find the Hub48 Board ribbon cable that corresponds to the output slot in which you have installed the XO16 Card. The If you are installing the XO16 Card in a slot with a card Hub48 board’s five ribbon cables connect to the Input and slot cover, you must first remove the card slot cover.
-
Page 9: Installing An Xo16 Card In Sc48
Completing and Confirming Installation Installing an XO16 Card in SC48 To complete and confirm installation: Your SC48 has two available output card slots, slots D and E. These instructions assume you already have an output card in- Reattach the Mix Rack’s front panel. stalled in slot D and that slot E is empty. - Page 10 Remove the card from its packing material. Hold the card by Completing and Confirming Installation its edges. To complete and confirm installation: Connect the ribbon cable to the card socket. Make sure the Reconnect the power cable and any other cables to the pins on the socket are correctly aligned with the ribbon cable SC48.
-
Page 11: Chapter 3. Specifications
Chapter 3: Specifications Audio Specifications XO16 Analog Line Outputs Parameter Specifications Limit Units Condition/Comment Type Balanced, XLR3-Male Impedance Each leg to ground Maximum Output Level D/A Converter Latency 0.58 Fs=48kHz XO16 Digital Outputs Parameter Specifications Limit Units Condition/Comment Type Balanced, XLR3-Male Format AES3 (IEC-60958 Type I) Impedance... - Page 12 XO16 Analog/Digital Output Card...
Need help?
Do you have a question about the VENUE XO16 and is the answer not in the manual?
Questions and answers