Technical Data - Philips HP L2035 Service Manual

Technical Specifications
1. LCD monitor
Screen size : 359 mm x 287 mm
Maximal resolution :1600x1200 pixels
2.1 LCD Panel
Type NR. : LM201U04 (LG.PHILIPS)
Outline dimensions : 432.0(H)331.5(V)25.0(D) (Typ) mm
Pitch ( mm ) : 0.255 (per one triad) x 0.0.255mm
Color pixel arrangement: RGB vertical stripes
Display surface : low reflection, antiglare with hard coating
Color depth : 16777216 colors (8 bits)
Backlight : Six CCFL's
Active area(WxH) : 408x306mm (20.1 diagonal)
View angle : Horizontal & Vertical 170 degree (CR>5)
Contrast ratio : 300:1
White luminance : 250 nits (Typ)
2.2 Scanning frequencies
Hor. : 30 - 94 KHz
Ver. : 48 - 85 Hz
2.3 Video dot rate : < 205 MHz
2.4 Power input : 90-264 V AC, 50/60 +/- 2 Hz
2.5 Power consumption : < 75 W maximum
2.6 Dimensions : 466 * 460 * 220 mm
2.7 Weight : 9.5 KGS
2.8 Functions :
(1) D-shell analog R/G/B separate inputs, H/V sync separated,
Composite (H+V) TTL level, SOG sync
(2) DVI digital Panel Link TMDS input
(3) CVBS Video :1Vp-p,75 Ohm
(4) S-Video :Y-1Vp-p,75 Ohm
C-0.3Vp-p,75 Ohm
2.9 Ambient temperature : 5 C - 35 C
3.1 Interface signals
The input signals can be applied in three different modes :
1). D-shell Analog
Input signal : Video, Hsync., Vsync
Video : 0.7 Vp-p, input impedance, 75 ohm @DC
Sync. : Separate sync TTL level , input impedance 2k2 ohm terminate
Hor. sync Positive/Negative
Ver. sync Positive/Negative
Composite sync TTL level, input impedance 2k2 ohm
terminate (Positive/Negative)
Sync on green video 0.3 Vp-p Negative
(Video 0.7 Vp-p Positive)
2). Intel DVI Digital
Input signal : Single channel TMDS signal
3.1 Interface
3.2.1 D-Sub Cable
Length : 1870 mm (fixed) /with H-sync
impedence 50 Ohm +/- 10%
Connector type : D-sub male with DDC2B pin
assignments.
Blue connector thumb-operated jack screws

Technical Data

O O
Pin Assignment
D-Sub connector
10
Pin No. Assignment
1 Red video input
2 Green video input / Sync On Green
3 Blue video input
4 Sense (Ground)
5 Not connected
6 Red video ground
7 Green video ground
8 Blue video ground
9 NC
10 Sync. ground
11 Sense Ground
12 Bi-directional data
13 H/H+V Sync
14 V. Sync
15 Data Clock
The digital/analog DVI-I connector contains 29 signal contacts
organized in three rows of eight contacts. Signal pin
assignments are listed in the following table:
Pin No.
1 TMDS data2-
2 TMDS data2+
3 TMDS data2 shield
4 NC
5 NC
6 DDC clock
7 DDC data
8 Analog V-sync
9 TMDS data1-
10 TMDS data1+
11 TMDS data1 shield
12 NC
13 NC
14 +5V
15 Ground(return for +5V and H/Vsync)
16 Hot plug detect
17 TMDS data0-
18 TMDS data0+
19 TMDS data0 shield
20 NC
21 NC
22 TMDS clock shield
23 TMDS clock+
24 TMDS clock-
C1 Analog R
C2 Analog G
C3 Analog B
C4 Analog H-sync
C5 Analog GND (Analog R, G, Breturn)
3
HP L2035
Go to cover page
1
5
6
11
15
Description