Specifications; Mounting The Saw - Chicago Electric 68819 Manual

Specifications

Motor 120 V~ / 60 Hz / 15 A
No load speed 4800 RPM
Blade 10" Diameter, 5/8" Arbor, 60 TPI
Positive Table 0°, 15°, 22.5°, 30° and
Stops 45° both right and left
Bevel Capacity 0° to 45° left
Laser Power
2 'AAA' batteries
Supply
Cutting Capacities
Straight Cut @ 90° 2.3 IN. H. x 4.6 IN. W.
Miter Cut @ 45° 1.5 IN. H. x 4.6 IN. W.
Straight Bevel
2.3 IN. H x 3.3 IN. W.
Cut @ 45°
Compound Cut @
45° Left and 2.3 IN. H. x 3.3 IN. W.
45° Right
Included Blade Wrench, Dust Bag, Extension
Accessories Supports, Spare Carbon Brushes
avoID eXpoSuRe
Laser light is emitted
from this aperture.
CautIon Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
CautIon The use of optical instruments
with this product will increase eye hazard.
List of Contents
Description
Compound Sliding Miter Saw
12" Carbide Tipped Blade
Extension Support
Dust Collection Bag
Rubber Foot Pads
Wrench
Initial Set up Instructions
Read the entIRe IMpoRtant SaFetY
InFoRMatIon section at the beginning of
this manual including all text under
Page 6
LaSeR LIGht
Do not StaRe Into beaM
Max. output: 1 mW,
Wavelength: 650 nm
CLASS II LASER PRODUCT
This product complies with
21 CFR 1040.10 and 1040.11
NO. 20 Zhoucheng Road, Henghe
Industrial Zone, Cixi City, Zheniang, China
Manufacture Date: ___________, _______
Qty
1
1
2
1
4
1
For technical questions, please call 1-800-444-3353.
subheadings therein before set up or use of
this product.
to pRevent SeRIouS InJuRY FRoM aCCIDentaL
opeRatIon:
turn the power Switch of the tool to its
"oFF" position and unplug the tool from
its electrical outlet before assembling or
making any adjustments to the tool.
note: For additional information regarding the
parts listed in the following pages, refer to the
Assembly Diagram near the end of this manual
and Figure B: Components on page 5.
assembly
attaching the extension Supports
Insert the ends of the Extension Supports into the
holes in the sides of the Base. Tighten the Screws
on the back of the Table to hold the Extensions in
place. The upper edge of the Extensions will be
level with the surface of the Table. This provides
a wider base for the work material to rest on.
attaching the Dust Collection bag
The Dust Collection Bag slips over the Dust Outlet
behind the Blade Housing Assembly. Sawdust
created by cutting is captured in the bag.
attaching the hold Down vise
The Hold Down Vise is used to hold the
work piece in place. It can be mounted in
either of the two holes behind the fence.

Mounting the Saw

Mount the Miter Saw to a sturdy level surface
at the mounting hole locations before use.
WaRnInG! Do not use the saw without first
securing it, either temporarily or permanently, to
a sturdy stationary work surface that can support
the tool and will keep it from tipping during use.
If mounting permanently to a table or other stationary
surface, secure in place through the four mounting
holes on the base of the unit using 3/8" bolts, lock
washers, washers and nuts. This will help prevent
injury from tipping or movement of the saw. The use
of a saw table will make it easier to efficiently handle
work materials and make more accurate cuts.
adjusting Cutting head
To disengage the Cutting Head from
its shipping/storage position:
1. Lightly push down on the Cutting Head.
SKU 68819