Related Manuals for Navitar VideoMate 2030
Summary of Contents for Navitar VideoMate 2030
- Page 1 All manuals and user guides at all-guides.com 2030/2030 IDEO Video Slide Projector Instruction Manual The World Leader in Image Quality...
-
Page 2: Table Of Contents
All manuals and user guides at all-guides.com Table of Contents Product Overview Safety Precautions Voltage Selection Installation Slide Tray Installation 11 Lamp/Fuse Replacement 13 Troubleshooting 15 Specifications 16 Appendix 17 Warranty... -
Page 3: Product Overview
Some of the “best” pictures around are stored on the millions of existing 35mm slides. The sole function of the VideoMate 2030 (NTSC) & 2030 (PAL) is to provide an electronic representation of the contents of a normal 35mm slide. The output signals available are Composite Video and S-Video. -
Page 4: Safety Precautions
All manuals and user guides at all-guides.com Safety Precautions Safety Precautions For safety, before connecting the projector to the main, ensure that the voltage selector is set to your main voltage and the required fuse is fitted. An incorrectly adjusted main voltage can damage the projector. To prevent damage to equipment and operating personnel, please observe the following precautions: Insure that the voltage source contains a satisfactory path... -
Page 5: Voltage Selection
All manuals and user guides at all-guides.com Voltage Selection Voltage Selection Check voltage setting. The Navitar VideoMate will be exported throughout the world to countries with differing mains voltages. The projectors are already set during manufacture to a fixed main voltage. - Page 6 All manuals and user guides at all-guides.com Voltage Selection Voltage Selector Lock Ring Alignment Mark Tray Positioning Fuse Holder Index Mark...
-
Page 7: Installation
All manuals and user guides at all-guides.com Installation Installation Before installing please review precautions. For those users familiar with both the operation of 35mm slide projector and their own video displays, the following is an abbreviated start-up procedure. 1. Check the voltage setting before powering on. Make sure that the setting is correct. - Page 8 All manuals and user guides at all-guides.com Installation 9. To shut down the system, hold down the select bar and rotate the slide tray to the “0” index position. Set the power switch to “off”. 10. For instructions regarding setting up slide tray changing lamps, etc., refer to the appropriate section of the manual.
-
Page 9: Slide Tray Installation
This system was designed to permit usage of prepared presentations without reorientation of the slides in the tray. Your new Navitar VideoMate will accept Kodak Ektapro 80, Kodak Ektagraphic 80 for holding 80 slides with a maximum slide mount thickness of 3.2mm and Kodak Carousel Transvue 140 Slide Tray for holding 140 slides with a maximum mount thickness of 1.6mm. - Page 10 All manuals and user guides at all-guides.com Slide Tray Installation Slide Tray Removal To remove the tray from the projector without losing slides: 1. Hold the selector bar down and rotate the tray back to the zero index position. 2. Lift the tray at a point opposite the index mark. Slide Tray Jam The tray may jam if a damaged slide is caught in the gate.
-
Page 11: Lamp/Fuse Replacement
All manuals and user guides at all-guides.com Lamps/Fuse Replacement Lamps The VideoMate will function with either of the following 82 volt or 85 watt lamps. One provides a higher color temperature, with the other exhibits a much longer life. Do not use 82 volt, 25-300 watt slide projection lamps or your equipment will suffer severe damage. - Page 12 All manuals and user guides at all-guides.com Lamps/Fuse Replacement 4. Reverse the procedure to insert a new lamp (make sure the new lamp is properly seated). 5. Lock the new lamp in place with wire bail. Fuses Always switch off the projector and unplug the main lead before replacing a fuse.
-
Page 13: Troubleshooting
All manuals and user guides at all-guides.com Troubleshooting Troubleshooting Symptom #1: After switching on, projector is not operable. Possible Cause: 1. All equipment not “powered up”. Check outlets and individual unit (monitor, video projector, etc.). 2. Check input voltage selector. 3. - Page 14 All manuals and user guides at all-guides.com Troubleshooting Symptom #4 Image too dark or too light. Possible cause: 1. Illumination level inadequate. Set knob “I” as required. 2. Monitor not adjusted properly. Symptom #5 Image not sharp. Possible cause: 1. Adjust focus knob. 2.
-
Page 15: Specifications
All manuals and user guides at all-guides.com Specifications i f i o i t " 2 i l r r o l t l i r o l a l i ) e l l a t o i t n i l v i t y t i... -
Page 16: Appendix
Horizontal Movement 1 2 3 4 5 6 1 2 3 4 5 6 Screw #2 Do Not Remove Lower Plug Ektalite and Kodak are both trademarks of the Eastman Kodak Company. VideoMate and Navitar are both trademarks of Navitar, Inc. -
Page 17: Warranty
If during the warranty period the product is found to be defective, it will be repaired or replaced at the facilities of Navitar. However, Navitar reserves the right to refund the purchase price if the replacement or repair is not commercially practical or timely. - Page 18 All manuals and user guides at all-guides.com Navitar, Inc. 200 Commerce Drive Rochester, NY 14623 (716) 359-4000 phone (716) 359-4999 fax Internet http://navitar.com/ e-mail info@navitar.com...