Dvd Operation During Timer Recording; Display Button; Copying A Video Tape; Mts System (Multi-Channel Television Sound) - Sylvania SRD4900 Owner's Manual

DVD Operation During Timer Recording

• If there is a power failure or the DVD/VCR has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost.
• If a tape is not in the DVD/VCR or does not have the record tab, the
insert a recordable tape.
• If a tape ends during timer recording, the VCR will stop, eject the tape, and switch to the DVD mode automatically as the
(If the DVD power is off, the VCR will become STANDBY status).
• When all timer recordings are finished, the
• When timer recordings are set, the
SET button so that the
continue with the other features as described in this manual.
If you want to use the DVD player during a VCR timer recording or while the
• You can use the DVD player while the
Press the DVD button on the remote control to choose DVD mode, then continue with the other DVD features as described in this manu-
al. You don't have to set the TIMER off to use the DVD only.

Copying a Video Tape

Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
(Back of another source)
AUDIO OUT
1
L
DVD/VCR VCR
or
COMPONENT
AUDIO OUT AUDIO IN
VIDEO OUT
ANT-IN
Y L L
Connect
R
C R R
B
VIDEO OUT VIDEO OUT VIDEO IN ANT-OUT
C
R
Audio/Video cables
(supplied)
Hint
Hint
• For best results during dubbing, use the front panel controls whenever possible.
The remote control might affect another source's operation.
• Always use video-quality shielded cables with RCA-type connectors. Standard
audio cables are not recommended.
• You can use a video disc player, satellite receiver, or other audio/video compo-
nent with A/V outputs.
• "L1" or "L2" is found before the lowest memorized channel. (Example: CH02)
• "L2" input jacks are on the front of this DVD/VCR.

MTS System (Multi-Channel Television Sound)

When You Receive or Record a
Program Broadcast in MTS
• When you receive a broadcast on
the VCR, you can check the type
of the broadcast by pressing the

DISPLAY button.

• When "TV STEREO" or "SAP"
selection is valid, select them by
following steps. This selection is
needed when you record the pro-
gram.
• SAP means Second Audio
Program (usually second lan-
guage).
Display on the Type of
TV screen broadcast
Regular
-None-
(monaural audio)
Stereo
STEREO
broadcast
Bilingual
SAP
broadcast
(second audio program)
Stereo & (stereo main audio program)
STEREO
Bilingual
SAP
broadcast
(second audio program)
light will flash.
light will appears. To use the VCR as usual until the time for the recording, press the SUBTITLE/T-
light disappears. Press the VCR/TV button to choose the VCR position. Select either VCR or DVD mode, then
light is on or flashes, or during a timer recording. Press the POWER button to turn on the DVD.
(Back of Recording DVD/VCR*)
DVD DVD/VCR VCR
DIGITAL COMPONENT
AUDIO S-VIDEO AUDIO OUT AUDIO IN Connect
VIDEO OUT
AUDIO OUT OUT OUT ANT-IN
Y L L
L
C R R
B
COAXIAL
R VIDEO OUT VIDEO IN ANT-OUT
C
R
RF cable
(supplied)
*Front input jacks are also available
VCR VCR VCR
1
1
2
2
To exit the menu.
When You Play Back a Tape
STEREO/SAP
Recorded in Hi-Fi Stereo
Selection
-Invalid-
• If you have connected a stereo TV to
-Invalid-
this DVD/VCR, select "STEREO".
TV STEREO
• If you have connected a monaural TV
(main audio program)
SAP to this DVD/VCR, select "MONO".
TV STEREO
Your Selection
Type of recorded tape
SAP
non Hi-Fi tapes
Hi-Fi tapes
recorded in
Hi-Fi stereo
Hi-Fi tapes
recorded main
audio program
Hi-Fi tapes
recorded second
audio program
light flashes and timer recording cannot be performed. Please
1) Insert a pre-recorded tape into the playing VCR.
(Back of TV)
2) Insert a tape with its record tab into the recording
DVD/VCR.
2
3) Press
recording DVD/VCR to select the desired recording
speed (SP/SLP).
4) Select the "L1" or "L2" position on the recording DVD/VCR.
• To use the input jacks on the back of this unit, select
"L1" position by pressing [0], [0], [1] on the remote
control or the CHANNEL buttons.
• To use the input jacks on the front of this unit, select
"L2" position by pressing [0], [0], [2] on the remote
control or the CHANNEL buttons.
5) Press the REC/OTR button on the recording DVD/VCR.
6) Begin playback of the tape.
7) To stop recording, press the STOP/EJECT button on
the recording DVD/VCR, then stop playback of the tape
in another source.
VCR VCR
MENU
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
B TV STEREO [ON]
or
SAP
Select "TV STEREO" or
"SAP"
CLEAR/
C. RESET
STEREO
MONO
L-channel R-channel
Monaural Monaural Monaural
L R L+R
Main audio Main audio Main audio
program program program
Second audio Second audio Second audio
program program program
– 13 –
light is on or flashes.
the SPEED button on the remote control of the
VCR VCR
VCR VCR VCR
1
1
MENU
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
B AUDIO OUT
TV STEREO
SAP
or
2
2
B HIFI
or MONO
Select "HIFI" or "MONO"
3
3
To exit the menu.
CLEAR/
C. RESET
light flashes.
-MENU-
[ON]
AUDIO OUT
[ON]
EN