Eldat RCU01-4104M-01 Operating Instructions

GB
Universal Receiver RCU01 (4-Channel)
Models
RCU01-4104M-01: 433.92 MHz
RCU01-5004M-01: 868.3 MHz
Package Content
Universal Receiver incl. HF antenna,
Mounting accessories, Screw fittings set,
Operating instructions
Technical Data
Frequency: 433.92 or 868.30 MHz
Power supply: 230 V AC / 12-24 V DC
Output: 4 potential-free relay
contacts
Max. load: 230 V AC: see Table
30 V DC: 3 A / 90 W
Response time: approx. 1 second
Degree of protection: IP54
Operating temperature: -20° C to +60° C
Dimensions: 150 x 110 x 50 mm
Weight: approx. 500 g
Intended Use
The unit may only be used as a radio con-
trol system together with low voltage or
mains voltage devices!
The manufacturer shall not be liable for any
damage caused by improper or non-
intended use!
Safety Advice
Warning! While being pro-
grammed, the Universal Re-
ceiver is live!
Do not touch the terminals! Only use
suitable tools!
Carefully read through these instructions
before connecting and operating the Uni-
versal Receiver!
Electrical installation and programming
may only be carried out by a qualified
electrician!
Observe the applicable laws, standards
and regulations, particulary EN 60669!
Caution! The primary input of the Uni-
versal Receiver must be protected by a
50 mA fuse.
Have faulty units checked by the manufac-
turer!
Do not make any unauthorized alterations
or modifications to the unit!
Non-observance of the installation instruc-
tions may cause fire or other hazards.
Function
The unit is a universally applicable four
channel radio control system, which can be
operated both with low voltage and mains
voltage.
The Universal Receiver can memorize 4
transmission codes for each channel. For
each channel different operating modes can
be programmed: Impulse, ON/OFF (1- and
2-button operation), timer (30 seconds and
3 minutes), continuous and awning opera-
tion.
General Information
Do not mount the Universal Receiver near
the floor or near large metal objects!
The maximum length of all connecting
cables may not exceed 3 m.
The reception quality can be affected by a
number of factors:
•
location, Transmitter
•
equipment and systems without interfe-
rence suppression
•
other transmitters within the frequency
range
•
atmospheric conditions and other fac-
tors.
In case of malfunctions, please contact your
dealer or the manufacturer.
Connection Diagram
21
REL1
22
23
24
REL2
25
26
27
REL3
28
29
30
REL4
31
32
S1 Dip switch for memory
location select
DR1 Rotary switch for
operating mode select
H1 LED
TA1 – TA4 Programming buttons for
channels 1-4
REL1 – REL4 Relays 1-4 for
devices 1-4
V1 – V4 Connecting terminals for
relays 1-4
BU1 Antenna socket
ST1 Connecting terminal for
mains voltage 230 V AC
ST2 Connecting terminal for
low voltage 12-24 V DC
Start-Up
Start-up the Universal Receiver in three
steps:
1. Installing the Universal Receiver
2. Programming the operating mode
3. Memorizing the transmission codes
Installing the Universal Receiver
1. Unscrew the housing cover.
2. Use the screws and mollies supplied, to
mount the Universal Receiver on the
wall.
3. Connect the low voltage or mains
voltage devices to be switched to the
connecting terminals V1 to V4 according
to the connection plan. The connecting
terminals are plug-type terminals.
Max. load:
230 V AC: see Table of Loads
30 V DC: 3 A / 90 W
4. Connect the power supply cables to the
connecting terminal ST1 (mains voltage
230 V AC) or ST2 (low voltage 12-24 V
DC) according to the connection plan.
The connecting terminal ST1 is a plug-
type terminal.
Note: All cables are to be fed into the
Universal Receiver via the openings on
the bottom using the watertight PG
screw fittings.
5. Switch on the supply voltage. The LED
H1 lights up for approx. 1 sec.
6. Carry out a function check:
Press any button of the transmitter. The
LED H1 of the Universal Receiver
should flash rapidly.
Table of Loads (AC)
Type of load Max. load
230 V AC / 50Hz
Resistive load:
Light bulbs, 230 V
Halogen lamps etc. 8 A / 1,840 VA
Inductive load:
Halogen lamps with wound
transformers
(transformer at least 85%
loaded) 2.6 A / 600 VA
Non-compensated or series-
compensated fluorescent
lamps with ferromagnetic
ballast 8 A / 1,840 VA
Parallel-compensated
fluorescent lamps with
ferromagnetic ballast 2.6 A / 600 VA
Capacity EB:
electronic ballast, electronic
transformers etc. 4 A / 920 VA