Install Additional Mass Storage Devices - HP NetServer E60 Installation Road Map

6

Install Additional Mass Storage Devices

NOTE With certain mass storage configurations, you may need additional cables or adapters. (See the HP NetServer
Installation Guide
configuration information and part numbers for HP cables, adapters, and trays, see HP Information Assistant or Order
Installing Internal SCSI Mass Storage Devices
1. Configure the device:
uses cable termination). Refer to the drive's user guide for details.
Boot Device Priority
The system searches for a bootable device in this order: 1) IDE CD-ROM drive with a bootable CD-ROM. 2) Flexible disk drive with a bootable
flexible disk. 3) Embedded SCSI A. 4) Embedded SCSI B. SCSI devices on any one SCSI channel (SCSI A or B)will boot in the following order:
0,1,2,3,4,5,6.
2. Remove the cover:
NetServer on its side and open the air duct. To add or remove a tape drive, leave the NetServer standing on its feet.
3. Adding Hard Disk Drives
Remove the hard disk drive cage:
!
connectors for any hard disks already in the cage. Remove the cage. See Figure A.
Insert new hard disk drive:
!
Secure hard disk drive:
!
in the back, and then in the elongated hole on the same side. Repeat on the other side. Screws are TORX 15, #6-32, not to exceed 1/4-inch in length.
See Figure B.
Reinstall cage:
!
Hard Disk
Drive Cage
Screws
4. Adding a Tape Drive
Remove the bezel:
!
Loosen all six catches and remove. See D.
Unsnap and remove cover plate:
!
Remove filler piece:
!
Insert tape drive:
!
Secure the tape drive:
!
C
5. Installing the External SCSI Mass Storage Device
Connector
Obtain External SCSI Cable Kit (HP P/N D8214A):
!
Order from your dealer.
Remove cover:
!
as described in Part 3.
Remover external SCSI connector knock-out:
!
flat blade screwdriver to remove the knock-out at the rear of the
system. See illustration in Part 9.
Install SCSI cable:
!
on the system board and to the knock-out at the rear. See I and J.
Replace cover
!
6. Connect the cables:
HP NetServer E60 Installation Guide
7. Replace the bezel and cover:
for information on installing the optional external SCSI port, and for duplexing information.) For
Set the jumpers on the disk drive to an unused SCSI address. Make sure the device is not terminated (the NetServer E 60
and prepare the NetServer as described in Part 3: " Remove the Cover."To add or remove from the hard disk drive cage, lay the
Loosen the three captive screws securing the hard disk drive cage. Unplug the power and SCSI
Insert the hard disk drive into the cage with the connectors inside and toward the feet. See Figure B.
Align the disk drive' s screw holes with the round and elongated holes in the cage. Insert screws in one round hole
Reinsert the disk drive cage into the chassis. Tabs at front of the cage fit into slots in the chassis. Tighten the three captive screws.
Top
A
Front
Starting at the top, on both sides, begin by deflecting bezel catches outward while gently pulling the bezel. See C.
From the back, unsnap and remove the filler panel. See E.
Remove the sheet metal filler piece. See F.
Insert the tape drive from the front. See G.
Secure the drive with screws through the holes at the bottom position in the top shelf. See H.
D
Remover the cover and position the NetServer
Attach the cable to the free SCSI connector
as described in Part 8.
Connect SCSI and power cables to the drives. If doing internal hard disk drive duplexing, see Chapter 4 in the
.
Replace the bezel by pushing the bezel back into place. Replace the cover as described in Part 8.
E
F
I
Use a
E 60
B
Slots for tabs
Captive screws
(One hidden)
Tabs
First, insert screws through round
holes at back (one each side).
G
Screws
Top
H
J