Table of Contents
Advertisement
Quick Links
Instructions - Parts List
Two-Ball NXT
1000cc Pumps
Designed for low pressure, medium volume circulation of finishing materials.
For professional use only.
Models P06DCK, P06ECK, P06LCK, P06MCK,
P06DSG, P06ESG, P06LSG, P06MSG
620 psi (4.2 MPa, 42.7 bar) Maximum Working Pressure
100 psi (0.69 MPa, 6.9 bar) Maximum Air Inlet Pressure
Models P10DCK, P10ECK, P10LCK, P10MCK, P10LCS
1180 psi (8.14 MPa, 81.4 bar) Maximum Working Pressure
100 psi (0.69 MPa, 6.9 bar) Maximum Air Inlet Pressure
Important Safety Instructions
Read all warnings and instructions in Operation manual.
Save these instructions.
See page 2 for Table of Contents.
Patent Pending
®
311833F
EN
ti8377b
II 2 G
Advertisement
Table of Contents
Related Manuals for Graco P06DCK
Summary of Contents for Graco P06DCK
- Page 1 311833F Designed for low pressure, medium volume circulation of finishing materials. For professional use only. Models P06DCK, P06ECK, P06LCK, P06MCK, P06DSG, P06ESG, P06LSG, P06MSG 620 psi (4.2 MPa, 42.7 bar) Maximum Working Pressure 100 psi (0.69 MPa, 6.9 bar) Maximum Air Inlet Pressure Models P10DCK, P10ECK, P10LCK, P10MCK, P10LCS 1180 psi (8.14 MPa, 81.4 bar) Maximum Working Pressure...
-
Page 2: Table Of Contents
Lubrication ......9 Graco Information ......20 Troubleshooting . -
Page 3: Pumps With Nxt ® Air Motors Part No. Matrix
® Pumps with NXT Air Motors Part No. Matrix ® Pumps with NXT Air Motors Part No. Matrix Check your pump’s identification plate (ID) for the 6-digit part number of your pump. Use the following matrix to define the construction of your pump, based on the six digits. For example, Pump Part No. P 0 6 M S G represents ™... -
Page 4: Warnings
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. - Page 5 Warnings WARNING PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. • Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.
-
Page 6: Installation
Installation Installation Grounding Solvent pails used when flushing: follow local code. Use only conductive metal pails, placed on a grounded surface. Do not place the pail on a nonconductive sur- face, such as paper or cardboard, which interrupts grounding continuity. To maintain grounding continuity when flushing or The equipment must be grounded. -
Page 7: Flush Before Using Equipment
Installation • Fluid drain valve: required in your system, to relieve fluid pressure in the hose and gun. • Fluid shutoff valve: shuts off fluid flow. • Fluid pressure regulator: for more precise adjust- ment of the fluid pressure. • Gun or valve: to dispense fluid. -
Page 8: Operation
Operation Operation Pressure Relief Procedure 1. Engage trigger lock. 2. Close the bleed-type master air valve. 3. Disengage the trigger lock. 4. Hold a metal part of the gun firmly to a grounded metal pail. Trigger the gun to relieve pressure. 5. -
Page 9: Maintenance
Maintenance Maintenance Shutdown To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pres- sure Relief Procedure on page 8. To reduce risk of static sparking or splashing in the eyes To reduce the risk of serious injury whenever you are or on the skin, relieve the pressure and remove the instructed to relieve pressure, always follow the Pres- spray tip before flushing. - Page 10 Maintenance 311833F...
-
Page 11: Troubleshooting
Troubleshooting Troubleshooting 2. Check all possible problems and solutions before disassembling pump. To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pres- sure Relief Procedure on page 8. Never operate the pump with the air motor shield removed. -
Page 12: Repair
Repair Repair Required Tools 5. Hold the tie rod flats with a wrench to keep the rods (6) from turning. Unscrew the nuts (7). Remove the lower (2). • Set of socket wrenches • Set of adjustable wrenches 6. To service the lower, refer to manual 311716 or •... -
Page 13: Reconnect The Lower
7. Reconnect all hoses. Reconnect the ground wire if it (4) are in place on the displacement rod. was disconnected. Fill the wet-cup 1/3 full of Graco 4. Use at least two people to hold the lower while Throat Seal Liquid or compatible solvent. -
Page 14: Models
Repair Models P06DSG, P06ESG, Models P06LSG, P06MSG P06DCK, P06ECK, P06LCK, P06MCK,P10DCK, P10ECK, P10LCK, P10MCK, P10LCS ti8334b ti8335b 311833F... -
Page 15: P06Dck, P06Eck, P06Lck, P06Mck
120588 120588 WRENCH, wet cup 184278 184278 184278 184278 Ref. Description P06DCK P06ECK P06LCK P06MCK Qty. MOTOR, 3400, de-icing std; see manual 311238 N34DN0 MOTOR, 3400, de-icing datatrak; see manual 311238 N34DT0 MOTOR, 3400, low noise std; see manual 311238 N34LN0 MOTOR, 3400, low noise datatrak;... -
Page 16: Dimensions
Dimensions Dimensions ti8377b Approx. Weight Pump Model in. (mm) in. (mm) lb (kg) P06_SG 41.6 (1055) 28.0 (711) 113 (51) P06_CK 41.6 (1055) 28.0 (711) 113 (51) P10_CK 41.6 (1055) 28.0 (711) 132 (62) P10_CS 41.6 (1055) 28.0 (711) 132 (62) 311833F... -
Page 17: Pump Mounting Hole Diagram
Pump Mounting Hole Diagram Pump Mounting Hole Diagram NXT Model 3400 Four 3/8-16 Mounting Holes 6.186 in. (157 mm) Six 5/8-11 Tie Rod Holes 6.186 in. TI8070A (157 mm) NXT Model 6500 Four 3/8-16 Mounting Holes 101.6 mm (4.0 in.) 6.180 in. -
Page 18: Technical Data
Technical Data Technical Data Maximum Maximum Fluid Flow at Working Pressure Air Input Pressure 60 cycles per minute Model psi (MPa, bar) psi (MPa, bar) Air Consumption gpm (lpm) All P06 _ _ _ Models 620 (4.2, 42) 100 (0.69, 6.9) 17.4 (65.8) See Performance Chart All P10 _ _ _ Models... - Page 19 Technical Data 0.7 MPa, 7 bar (100 psi) air pressure or 10.5 MPa, 105 bar (1500 psi) hydraulic oil pressure 0.5 MPa, 4.9 bar (70 psi) air pressure or 7.5 MPa, 75 bar (1050 psi) hydraulic oil pressure 0.3 MPa, 2.8 bar (40 psi) air pressure or 4.2 MPa, 42 bar (600 psi) hydraulic oil pressure Test Fluid: No.
-
Page 20: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
Need help?
Do you have a question about the P06DCK and is the answer not in the manual?
Questions and answers