Table of Contents
Advertisement
Quick Links
Instructions-Parts List
President
Pumps
Air-powered pumps for low pressure, high volume circulation of finishing materials.
Do not use for flushing or purging lines with caustics, acids, abrasive line strippers, and
other similar fluids. For professional use only.
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
See page 3 for model information, including
maximum working pressure.
®
4-Ball
President Pump
with Open 4 Ball
Lower
3A3383D
EN
President Pump
with Sealed 4 Ball
Lower
II 2 G
Ex h IIB T3 Gb
Advertisement
Table of Contents
Related Manuals for Graco President 17E222
Summary of Contents for Graco President 17E222
- Page 1 Instructions-Parts List ® President 4-Ball Pumps 3A3383D Air-powered pumps for low pressure, high volume circulation of finishing materials. Do not use for flushing or purging lines with caustics, acids, abrasive line strippers, and other similar fluids. For professional use only. Important Safety Instructions Read all warnings and instructions in this manual.
-
Page 2: Table Of Contents
Stop Pump at Bottom of Stroke ... . 10 Graco Information ......22 Shutdown . -
Page 3: Models
Models Models Maximum Fluid Maximum Air Inlet Model Pump Lower Lower Lower Connection Working Pressure Pressure Series Ratio Length Size Material Style Style psi (MPa, bar) psi (MPa, bar) 17E222 standard 1000cc Sealed tri-clamp 460 (3.2, 32.0) 180 (1.2, 12) 17E223 standard 1000cc... -
Page 4: Warnings
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable. - Page 5 Warnings EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system com- ponent.
-
Page 6: Installation
Installation Installation Grounding Solvent pails used when flushing: follow local code. Use only conductive metal pails, placed on a grounded surface. Do not place the pail on a non-conductive sur- face, such as paper or cardboard, which interrupts grounding continuity. To maintain grounding continuity when flushing or The equipment must be grounded to reduce the risk relieving pressure: hold metal part of the spray gun or... -
Page 7: Mounting
Installation Mounting Plumbing See F . 2. Install a fluid shutoff valve (D) between the Stand Mount mix tank (A) and the pump. Order Part No. 253692 Pump Stand Kit (accessory). When using a stainless steel pump, use stainless steel Mount the pump in the pump stand and secure with the plumbing to maintain a corrosion-resistant system. -
Page 8: Accessories
Installation Accessories • Pump air regulator (L): to control pump speed and outlet pressure. Locate close to the pump. Install the following accessories in the order shown in • Air line filter (K): removes harmful dirt and mois- . 2, using adapters as necessary. ture from compressed air supply. - Page 9 Installation . 2. Typical Installation Key: Mix Tank Air Shutoff Valve (bleed-type) 255143 Wall Bracket Accessory (253692 Pump Stand Air Supply Line Accessory is also available) Air Line Filter Fluid Supply Line; 1-1/2 in. (38 mm) minimum diameter Air Regulator and Gauge Fluid Shutoff Valve Bleed-Type Master Air Valve Fluid Line...
-
Page 10: Operation
Operation Operation Pressure Relief Procedure 6. Connect the fluid line (E) to the pump outlet. 7. Open bleed-type air valve (M). Slowly turn pump air Follow the Pressure Relief Procedure when- regulator (L) clockwise, increasing pressure until ever you see this symbol. pump starts. -
Page 11: Maintenance
Maintenance Maintenance Preventive Maintenance Stall Test Schedule Perform a stall test periodically to ensure the piston seal is in good working condition and prevent system pres- The operating conditions of your particular system surization: determine how often maintenance is required. Establish a preventive maintenance schedule by recording when Close the fluid shutoff valve (D) closest to the pump on and what kind of maintenance is needed, and then... -
Page 12: Troubleshooting
Troubleshooting Troubleshooting Problem Cause Solution Pump output low on both strokes. Restricted air supply lines. Clear any obstructions; be sure all shutoff valves are open; increase pressure, but do not exceed maximum working pres- sure. Exhausted fluid supply. Refill and reprime pump. Clogged fluid outlet line, valves, etc. -
Page 13: Repair
Repair Repair Disassembly Reassembly 1. If the coupling adapter (8) and tie rods (4) have not been disassembled from the adapter plate (3), skip to step 2. If the coupling adapter (8) and tie rods (4) have been disassembled from the adapter plate (3), fol- low these steps: This equipment stays pressurized until pressure is manually relieved. - Page 14 Repair 5. Screw the lock nuts (5) onto the tie rods. Leave the lock nuts (5) loose enough to allow the lower to move so that it can be aligned correctly. 6. Insert the collars (11) into the coupling nut (10). Tighten the coupling nut (10) onto the coupling adapter (8) and torque to 90-100 ft-lb (122-135 N•m) to allow the pump rod to align the lower on the...
-
Page 15: Parts
Parts Parts 17E222 President Pump, 2:1 Ratio, Sealed, with 1000cc SST Lower 17E225 President Pump, 3:1 Ratio, Sealed, with 750cc SST Lower Ref. No. Part No. Description Qty. 205038 MOTOR, air, President; see manual 306982 LOWER, 4-Ball, see manual 333022A 17K657 Used on model 17E222 17K656... - Page 16 Parts 17E223 President Pump, 2:1 Ratio, Open, with 1000cc SST Lower 17E224 President Pump, 2:1 Ratio, Open, with 1000cc CST Lower 17E226 President Pump, 3:1 Ratio, Open, with 750cc SST Lower 17E227 President Pump, 3:1 Ratio, Open, with 750cc CST Lower 17E228 President Pump, 3:1 Ratio, Open, Stubby, with 750cc SST Lower 17E229 President Pump, 3:1 Ratio, Open, Stubby, with 750cc CST Lower Ref.
-
Page 17: Dimensions
Dimensions Dimensions Approx. Lower Weight Model Size Type Length in. (mm) in. (mm) in. (mm) in. (mm) lb (kg) 17E222 1000cc Sealed Standard 102 (46) 49 (1244) 32 (813) 25 (635) 17E225 750cc Sealed Standard 101 (45) 17E228 750cc Open Stubby 40 (1016) 21 (533) -
Page 18: Mounting Hole Layouts
Mounting Hole Layouts Mounting Hole Layouts 255143 Wall Bracket Accessory 17.8 in. (451 mm) 14.5 in. (368 mm) 12.4 in. (314 mm) 9.0 in. (229 mm) 5.4 in. (137 mm) 7.4 in. (187 mm) 5.3 in. (133 mm) 2.0 in. (51 mm) 1.0 in. -
Page 19: Model 253692 Floor Stand Accessory
Mounting Hole Layouts Model 253692 Floor Stand Accessory 17.0 in. (431.8 mm) 19.88 in. 16.88 in. (505.0 mm) (428.8 mm) TI15859a 14.50 in. (368.3 mm) 3A3383D... -
Page 20: Performance Charts
Performance Charts Performance Charts Fluid Outlet Pressure Air Consumption To find fluid outlet pressure (MPa/bar/psi) at a specific flow To find air consumption (l/min. or gpm) at a specific fluid flow (lpm/gpm) and operating pressure (A/B/C): (l/min. or gpm) and operating pressure (A/B/C): Locate desired flow at bottom of chart. -
Page 21: Technical Data
Technical Data Technical Data President 4 Ball Pumps U.S. Metric Lower Size 17E222,17E223, 17E224 1000cc 1000cc 17E225,17E226 17E227, 17E228, 17E229 750cc 750cc Maximum Fluid Working Pressure 460 psi 3.2 MPa, 32.0 bar Maximum Air Input Pressure 17E222,17E223, 17E224 180 psi 1.2 MPa, 12 bar 17E225,17E226 17E227, 17E228, 17E229... -
Page 22: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.