Summary of Contents for Leica Geosystems DISTO WH15
Page 1
Therefore this module is not intended to be sold as a final product or for any purposes other than the above- mentioned. Distance Reference Laser beam outlet Type: DISTO OEM module 3.0 WH15 Art. No.: 724866 Type: DISTO OEM module 3.0 WH30 Art. No.: 563890 Leica Geosystems AG CH-9435 Heerbrugg 1/12 725538.doc 08.11.01...
DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 Technical Reference Manual V1.20 2. Physical dimensions and fixing When fixing the Module you have to be careful not to point the instrument directly toward the sun.
DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 Technical Reference Manual V1.20 3. Interface parameters 3.1. Software parameters The interface of the DISTO OEM module 3.0 has been arranged so that it can be connected to a PC by means of an adapter.
DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 Technical Reference Manual V1.20 4. Power on /off • Pin 13 of the D-sub Connector is Open (Tristate): To switch the module on, use command “a” (See 6.2.1 RESET command (a) on page 9). To switch the module off, use the command “b”...
DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 Technical Reference Manual V1.20 Position Description: Remark Word index 00-99 With zeroes at start no significance In service mode as expansion of word index Attribute 0: Measured value 1: Manually-entered value...
Prohibited parameter in command entry, or prohibited command, or non-valid @E203 result Parameter set-up incorrect (Contact Leica Geosystems) @E217 Parity error (Prior to contacting Leica Geosystems please check the Terminal @E221 settings) Interface buffer overflow (Contact Leica Geosystems if error occurs when sending less than 24...
DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 Technical Reference Manual V1.20 6. Commands 6.1. General After a command has been entered, it is decoded and processed. If additional commands are sent, processing of the current command will be aborted if possible and the last command to be received will be processed.
DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 DISTO DISTO OEM module 3.0 WH15/WH30 OEM module 3.0 WH15/WH30 Technical Reference Manual V1.20 6.2.7. Tracking (H) Function: Triggers continuous measurement of distance. The measurements are continued until the next command is issued or until a fault arises.