FUTABA T18MZ Software Update Changes page 7

② Connect an S.BUS servo to the S.BUS setting connector on the back
of the transmitter. Connect the battery to the sensor unit using a 2-way
cord, etc.
*Please note, this function is not applicable to the S9070SB servo.
③ Read the servo data by touching the [Read] button.
④ An operation check signal is output to the servo from the transmitter.
When the transmitter switch or stick that controls the channel allocated to
the S.BUS servo is operated, the servo will move accordingly.
Data reset screen
This update allows the user to separately reset the information for user
menus and telemetry data, if desired. For example, it is now possible
to reset the telemetry information without impacting the other model
programming.
【Setting method】
① Open the data reset screen by touching the [Data Reset] button in the
Linkage Menu.
② To reset the user menu setting, touch the [User Menu] button. To reset
the telemetry settings, touch the [Telemetry] button.
Camera function shutter switch
This update allows the user to assign a switch/position to control the
camera function of the T18MZ.
【Setting method】
① Open the camera screen by touching the [Camera] button in the System
Menu.
② To determine the switch to be used for the camera shutter, press the
switch select button located below the shutter button. Next, determine the
switch and the activation direction.
Maximum engine revolution display by each condition
It is now possible to display maximum engine revolutions by each condition.
【Setting method】
① Touch the [Condition] button on the RPM display.
② The screen that appears next denotes the maximum RPM achieved for
each of the flight conditions programmed into the transmitter.
Next explanation is required when using
two or more the same kind of sensors.
【Example 1 Altitude sensor × 1, Temperature sensor × 1】
A setup is unnecessary.
Two sensors are packed by HUB and it connects with S.BUS2
of a receiver.
【Example 2 Altitude sensor × 1, Temperature sensor × 2】
One altitude sensor and one temperature sensor, it is
unnecessary to set up.
Sensor registration is needed about the 2nd temperature
sensors.
＜ Assignable slot ＞
The
required
Sensor
number
of slots
TEMP (SBS-01T) 1 slot
RPM
(SBS01RM,SBS- 1 slot
01RO)
Voltage (SBS-01V) 2 slots
Altitude (SBS-01A) 3 slots
GPS (SBS-01G) 8 slots
TEMP125-F1713 1 slot
VARIO-F1712 2 slots
VARIO-F1672 2 slots
GPS-F1675 8 slots
Sensor unit ID setting
There are two methodologies that may be used to register the
identification of the sensors used with the T18MZ. This may be done
manually within the transmitter's program. Alternatively, registration of the
sensor may be accomplished through the sensor unit registration function
which follows.
【Setting method】
① Open the sensor unit setting screen by touching the [Sensor] button
in the Linkage Menu. The name and ID of the sensor assigned to each
slot is displayed.
② Touch the [ID] button of the desired slot.
③ To manually enter, or change the identification of the desired sensor(s),
input the identification using the touchpad. When completed, press OK.
Sensor unit registration
The sensor unit of each transmitter slot is registered and the slot number
of each sensor unit is changed automatically.
【Setting method】
- 3 -
*Altitude sensors, GPS sensors and other
data sensor units may use multiple slots.
*The sensor which uses two or more slots
has restriction in a start slot.
The number which can be
used as a start slot
1 〜 31
1 〜 31
1 , 2 , 3 , 4 , 5 , 6 ,
8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 ,
1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 , 2 2 ,
2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0
1 , 2 , 3 , 4 , 5 ,
8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 ,
1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 ,
2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9
8 , 1 6 , 2 4
1 〜 31
1 , 2 , 3 , 4 , 5 , 6 ,
8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 ,
1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 , 2 2 ,
2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0
1 , 2 , 3 , 4 , 5 , 6 ,
8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 ,
1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 , 2 2 ,
2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0
8 , 1 6 , 2 4
Selling area
Global
Europe