Page 1
CPC805 EPIC Intel Atom N450 Based Processor Module User Manual Rev. 001a E Pre May 2012 The product described in this manual is compliant to all related CE standards.
CPC805 Table of Contents Table of Contents ..............................1 List of Tables ..............................2 List of Figures ..............................3 Notation Conventions............................4 General Safety Precautions..........................5 Unpacking, Inspection and Handling........................6 Three Year Warranty............................8 Introduction............................9 Overview ..............................9 CPC805 Versions..........................12 Delivery Checklist..........................12 Module Diagrams..........................13 1.4.1 Block Diagram ........................14 1.4.2 Module Layout ........................15 1.4.3...
This document contains information, which is property of Fastwel Co. Ltd. It is not allowed to reproduce it or transmit by any means, to translate the document or to convert it to any electronic form in full or in parts without antecedent written approval of Fastwel Co. Ltd. or one of its officially authorized agents.
CPC805 Notation Conventions Warning, ESD Sensitive Device! This symbol draws your attention to the information related to electro static sensitivity of your product and its components. To keep product safety and operability it is necessary to handle it with care and follow the ESD safety directions. Warning! This sign marks warnings about hot surfaces.
However, prolonged operation near the maximum temperature is not recommended by Fastwel or by electronic chip manufacturers due to thermal stress related failure mechanisms. These mechanisms are common to all silicon devices, they can reduce the MTBF of the product by increasing the failure probability.
If damage is observed (usually in the form of bent component leads or loose socketed components), contact Fastwel's official distributor from which you have purchased the product for additional instructions. Depending on the severity of the damage, the product may even need to be returned to the factory for repair.
Page 9
In performing all necessary installation and application operations, please follow only the instructions supplied by the present manual. In order to keep Fastwel’s warranty, you must not change or modify this product in any way, other than specifically approved by Fastwel or described in this manual.
If a product should fail through Fastwel's fault during the warranty period, it will be repaired free of charge. For out of warranty repairs, the customer will be invoiced for repair charges at current standard labor and materials rates.
This makes CPC805 an ideal device for building systems with long life cycle. The module is compatible with MS DOS, Fastwel DOS, Microsoft® Windows® XP Embedded, Windows 7 (Windows Embedded Compact 7), QNX, and Linux® operating systems.
Page 12
Introduction CPC805 Some of the CPC805's outstanding features are: Intel Atom N450 processor, 1.66 GHz § IA 32-bit & 64- bit; § Intel SIMD2&3 (SSE2 + SSE3 + SSSE3); Hyperthreading; § § 1 level caсhe: 32 KB instructions, 24 KB data; §...
Page 13
Introduction CPC805 USB 2.0 ports § Up to 480 Mb/s § Four ports at front panel § Six ports routed to Stack PC connector Parallel port § SPP/ECP/EPP compatible § Onboard connector PS/2 keyboard and mouse interface § Onboard connector Six serial ports High speed NS16C550 compatible §...
Introduction CPC805 CPC805 Versions All variants are available in two versions, for industrial (-40°C to +85°C) and for commercial (0°C to 70°C) temperature ranges. The customer can choose necessary configuration options using the following template: – – Basic product name: CPC805 Version: 2 GB RAM, 4 GB NAND flash...
Introduction CPC805 Package: Dimensions: 230 × 155 × 45 mm Gross weight: 595 grams Note: Keep the antistatic bag and the original package at least until the warranty period is over. It can be used for future storage or warranty shipments. Module Diagrams The diagrams in this section give visual information about the CPC805 module design, connectors and components layout.
Introduction CPC805 1.4.3 Front Side Connectors Figure 1-4: CPC805 Front Side View (Connectors) LEDs Ethernet + USB СОМ ( 3 RS-232 СОМ1 RS-232 The layout may slightly vary for different versions of the module. This view shows only the front side items. C P C 8 0 5 U s e r M a n u a l...
Introduction CPC805 Technical Specifications 1.5.1 Processor, Memory and Chipset CPC805 is a EPIC single board computer based on Intel® Atom N450 processor operating at 1.66 GHz. The core of Intel® Atom N450 processor has a unique performance to power consumption ratio. §...
Introduction CPC805 1.5.2 Interfaces PCI Bus § Spec. v.2.3 support § 32-bit, 33 MHz PCI bus § Up to four PCI bus mastering devices are supported § Routed to PC/104 PCI connector PCI-E Bus Routed to StackPC connector; § § Conforms to PCI-E v.1.1 specification;...
Introduction CPC805 Graphics Integrated graphics controller allows connection of analog CRT monitor and/or matrix display with LVDS interface. Dual monitor configurations are supported (clone/extended desktop). VGA interface: § Supports analog display resolutions of up to 1400 x 1050, at 60 Hz §...
Page 24
Introduction CPC805 Jumpers and External Buttons List and functions of the onboard jumpers: § BIOS Setup parameters reset to default values (XP4); § LVDS power voltage selection: 5 V or 3.3 V (XP2); PCI voltage selection: 5 V or 3.3 V (XP13); §...
3.0 V lithium battery for RTC in a battery holder; use Renata BR2032 or compatible 1.5.5 Software Operating Systems Supported operating systems: § MS DOS 6.22, Fastwel DOS 6.22; § Windows XP (Embedded); Windows 7 (Windows embedded compact 7); § § Linux 2.6;...
Functional Description CPC805 Functional Description Module Interfaces and Connectors 2.1.1 PC/104 PCI and StackPC Interfaces PC/104 PCI and StackPC connectors allow CPC805 to interface with expansion modules such as A/D converters, digital I/O modules, etc. A maximum of four expansion boards may be stacked on the PC/104 PCI connector to form a fully-integrated system.
Functional Description CPC805 Table 2-3: SVGA J22 Front Side Connector Pinout Pin Number Signal Function In/Out Red video signal output Green Green video signal output Blue Blue video signal output VCC_MON Power +5V, 200 mA DDC_DATA C™ data In/Out HSYNC Horizontal sync.
Functional Description CPC805 Contact # Signal Description In/Out – – – – – – – – 1, 2, 3, 4 Panel Power 5V or 12V – 5, 6, 17, 18, 29, 30 Signal ground – TFT Panel Power Voltage Selection Figure 2-6: XP2 TFT Panel Power Voltage Selector XP2 is a standard 3-pin header used for TFT power voltage (V...
Functional Description CPC805 Digital Panel Backlight Control Figure 2-7: XP3 Panel Backlight Control Connector A 10-pin header on top side of CPC805 is used for connection of an invertor via IDC2-10 mating connector. Backlight control mode is selected by internal graphics controller driver for the installed operating system.
Functional Description CPC805 2.1.3 Audio Interface Audio connectors mounted on the top side of the board: LineOut (XP24); LineIn (XP25); Microphone (XP26). (TBA) Figure 2-8: Onboard CRIMP Audio Connectors: XP24, XP25, XP26 Pinouts of 3-pin onboard audio connectors are presented in two tables below.
Functional Description CPC805 2.1.9 CompactFlash Socket CPC805 has a CompactFlash Type I/II 50-pin socket XP27 on the bottom side of the board. (TBA) Table 2-8: CompactFlash Socket XP27 Pinout Pin Number Signal Function In/Out Ground signal – Data 3 In/Out Data 4 In/Out Data 5...
Functional Description CPC805 2.1.10 PS/2 Keyboard/Mouse Interface Figure 2-10: PS/2 Connector PS/2 port is available via a 1-row 7-contact onboard connector (XP22). Mouse and keyboard can be connected simultaneously using Y-cable (supplied with the module). The pinout of this connector is shown in the table below. Table 2-9: PS/2 Connector Pinout Pin Number...
Functional Description CPC805 2.1.13 Soft Power and Reset Connectors 2-pin connectors SoftPower and Reset (XP8 and XP9) are located on the top side of the module. They are used for connection of remote buttons without closed (depressed) state latching. A button connected to XP8 pins allows to switch between several power states. Pressed once in S5 (Soft-off) mode, it switches the module into S0 (Full-on) mode.
Functional Description CPC805 LED Indicators Four LEDs are located on the front side of the module: Table 2-12: Front Side LEDs Name Function Description Fast blinking (~8 Hz) after power-on, slow blinking (~1 Hz) after BIOS is started until HL1 green Startup diagnostics INT 19h BIOS procedure is finished then lights constantly.
Functional Description CPC805 SPI Controller 2.3.1 SPI Controller Registers Table 2-13: SPI Controller and User LEDs Registers Index I/O Port Address Type Hard Reset Configuration Register 310h FRAM address value [7:0] 311h FRAM address value [14:8] 312h SPI data value [7:0] 313h SPI Control/Status register [7] –...
Functional Description CPC805 On selection of the FRAM mode the bus frequency is always 12.5 MHz. The last kilobyte of 32 KB is reserved for storage of BIOS Setup parameters and is not available for user. Bit <0> in 313h Control register switches the Automatic address increment mode when reading from / writing to the Data register (312h).
Functional Description CPC805 Timers CPC805 is equipped with the following timers: RTC – Real-Time Clock ¢ ICH contains a real-time clock. The RTC includes 256 bytes of battery-backed CMOS RAM. The RTC features include timekeeping with alarm function and 100-year calendar. A coin-cell battery powers the real-time clock and CMOS memory.
Functional Description CPC805 I/O Registers of the WDT Controller Timer Current Value Register [23:0] Base+0h Name Description Write/read: Timer_Current_Value[7:0] Bits 7:0 of the current counter value Base+1h Name Description Write/read: Timer_Current_Value[15:8] Bits 15:8 of the current counter value Base+2h Name Description Write/read: Timer_Current_Value[23:16]...
Page 43
Functional Description CPC805 Status Register Base+6h Name Description Reserved Write/read: Second timeout flag. Is set "1" provided TMF=1. An interrupt is generated on this flag. If the module Reset is enabled (RSTE=1), Reset occurs. Cleared by writing "1" into this bit. Reserved Write/read: First timeout flag.
Safety Regulations The following safety regulations must be observed when installing or operating the CPC805. Fastwel assumes no responsibility for any damage resulting from infringement of these rules. Warning! When handling or operating the module, special attention should be paid to the heatsink, because it can get very hot during operation.
Installation CPC805 CPC805 Installation Procedure To install CPC805, follow the instructions below. Keep to the safety regulations of the Section 3.1 when performing the following operations. Warning! Failure to accomplish the following instruction may damage the module or result in incorrect system operation. Ensure that the module configuration corresponds to the application requirements before installing.
Installation CPC805 Dismounting Procedures To dismount the module do the following: When performing the next actions, keep to safety regulations of the Section 3.1. Pay special attention to the temperature of the heatsink! Ensure that the system power is switched off before proceeding. Disconnect all interface cables that may be connected to the module.
Installation CPC805 Note It is recommended to use CompactFlash-cards, which has been initialized and formatted in this module. By default, CPC805 utilizes LBA mode. Utilization of CompactFlash cards, which has been initialized and formatted in another mode, may lead to errors in operation of the module. 3.4.4 Battery Replacement The lithium battery must be replaced with Renata 3V CR2032 or a battery with similar...
Configuration CPC805 Configuration Power Supply Unit Type Selection A standard 2-pin jumper switch (XP10 near XS4) for selection of an external power supply type is installed on the top side of the module. Figure 4-1 below explains jumper positions. Figure 4-1: XP10 Power Supply Type Selector Positions ATX power supply with control functions (TBA) Open position of the jumper (default) corresponds to an unipolar...
Configuration CPC805 TFT Panel Power Voltage Selection XP2 is a standard 3-pin header used for TFT power voltage (V ) selection. It is located on the top side of the module. Figure below presents explanation of its jumper positions. Figure 4-3: XP2 TFT Panel Power Voltage Selector Pins 1-2 closed: +3.3 V power is supplied to a panel Contacts 2-3 closed: +5 V is supplied...
Phoenix® BIOS Setup CPC805 Phoenix® BIOS Setup The Phoenix® BIOS in your SBC is an adapted version of a standard BIOS for IBM PC AT-compatible personal computers equipped with Intel®x86 and compatible processors. The BIOS provides low-level support for the central processing, memory, and I/O system units. With the help of BIOS Setup program, you can modify BIOS configuration parameters and control special features of your module.
System Power CPC805 System Power Voltage Limits Table 6-1: DC Input Voltage Ranges and Limits (ATX or PC/104 PCI Power Supply) Power Voltage, V Maximum Permitted Value, V Absolute Limits, V +3.3 -0.3 to +4 3.135 to 3.465 -0.3V до 5.5V 4.75 5.25 +5B_SBY...
System Power CPC805 Table 6-4: Power Consumption (Unipolar Power Supply) Peak Max Power Consumption Version Mode Voltage Consumption Dissipation Current Current (TDP) (TDP) 2.2 A 3.9 A 15.5 W Max. load 12 V 1.3 A 2.4 A 16 W 30 V 0.6 A 1.1 A 18.5 W...
Troubleshooting CPC805 Troubleshooting Before contacting the service center in case of a problem, please read the following; the reason may be not the failure of the module. Problem Possible Reason Solution The module Autostart of the module is disabled Shortly close XP8 contacts. does not start, in BIOS.
Appendices CPC805 Appendices Related Standards and Specifications The Fastwel’s EPIC boards comply with the requirements of the following standards: Table 8-1: Related Standards Type Standard Test Parameters CE: Emission EN50081-1 – CE: Immission EN61000-6-2 – CE: Electrical safety EN60950 –...
Need help?
Do you have a question about the EPIC CPC805 and is the answer not in the manual?
Questions and answers