This document contains information, which is property of Fastwel Co. Ltd. It is not allowed to reproduce it or transmit by any means, to translate the document or to convert it to any electronic form in full or in parts without antecedent written approval of Fastwel Co. Ltd. or one of its officially authorized agents.
Specifications Safety Requirements This product of Fastwel Group Co. Ltd has been developed and tested with the purpose of ensuring its compliance with electrical safety requirements. Its design provides long-term trouble- free functioning. The product service life can be significantly shortened because of its incorrect handling during unpacking and installation.
To preserve the manufacturer's guarantee, the product must not be reworked or altered in any way. Any alterations and improvements not authorized by Fastwel Group Co. Ltd company, except those described in this Manual or obtained from the Fastwel Group Co.
Page 10
Returning a product for repair Apply to Fastwel company or to any of the Fastwel's official representatives for the Product Return Authorization. Attach a failure inspection report with a product to be returned in the form, accepted by customer, with a description of the failure circumstances and symptoms.
VIM552 Graphics Processor Module Specifications TRANSPORTATION, UNPACKING AND STORAGE a. Transportation The module should be transported in a separate packaging box (transport packaging) of the manufacturing facility, which consists of an individual antistatic bag and a cardboard box, in the...
VIM552 Graphics Processor Module Specifications APPLICATION NOTES AND GUIDELINES The modules should be used in the modes and under conditions set by the present User Manual, as well as technical specifications (TU 4013-006-52415667-05). Connection (disconnection) of external devices to the modules (from the module) in the running mode is not allowed.
This user manual (hereinafter referred to as the Manual) is meant for the insight into the device, its operation principle and general information required for the commissioning, intended use and maintenance of VIM552 (hereinafter referred to as the Module). ...
VIM552 Graphics Processor Module Specifications 2. SPECIFICATIONS The Module has the following I/O channels structure: DVI-I output (DVI1+RGB1) + USB (contacts 12, 13, option) VGA output (RGB0) on the front panel USB output on the front panel ...
VIM552 Graphics Processor Module Specifications 2.3. BLOCK DIAGRAM (BOARD LAYOUT) The block diagram of the module is shown on 2.2., the spot lines mark elements installed only in VIM552-02 versions. Filter (VIM552-02) Filter DD3-DD6 DDR SDRAM DVI1 Copy DVI Phy...
2.4. HARDWARE VERSIONS, ORDERING INFORMATION, DELIVERY CHECKLIST 2.4.1. Hardware versions, ordering information Module hardware versions and notations (ordering information) in FASTWEL product catalogs are specified in table 2.1. Table 2.1. – Module structure depending on the hardware version Name Notation at the...
VIM552 Graphics Processor Module Specifications 3. TECHNICAL CHARACTERISTICS 3.1. POWER SUPPLY The board is supplied with a voltage of +12V. Electric power supply of the module must meet the requirements cited in the table below. Voltage Minimum (V) Maximum Consumption current +12 В...
VIM552 Graphics Processor Module Specifications 3.5. WEIGHT AND DIMENSIONS Module weight should not exceed the values specified in table 3.1. Table 3.1 – Module weight Hardware version Weight, kg, no more than Weight with packaging, kg, no more than VIM552-01-I...
VIM552 Graphics Processor Module Appendices 4. DESCRIPTION AND OPERATION 4.1. DESIGNATION AND PINOUTS OF CONNECTORS The Module has the following structure of I/O channels: DVI-I output (DVI1+RGB1) + USB (option, contacts 12, 13) VGA output (RGB0) on the front panel...
4.2. Switching the graphics output to RearIO Switching the graphics output from the front panel to the board of Rear I/O (only in VIM552-02 versions) is carried out via SA1 switch. Switch position opposite to R symbol that conforms to rooting to RIO, position F –...
Page 23
1.2 Use of the Fastwel products as well as the objects of intellectual property containing in them, in the ways and for the purposes, not provided by the present user manual and datasheet isn't allowed without preliminary written approval of Fastwel.
Need help?
Do you have a question about the VIM552 and is the answer not in the manual?
Questions and answers