Qutepc-4100 series 0.6-liter box pc with intel 3rd generation core i3-3227u processor (36 pages)
Summary of Contents for Quanmax RAK-120S
Page 1
USER GUIDE RAK-120S Doc. User Guide, Rev. 1.0 Doc. ID: [To be Determined]...
Page 2
RAK-120S - User Guide, Rev. 1.0 This page has been intentionally left blank // 2...
Page 3
RAK-120S - User Guide, Rev. 1.0 RAK-120S - USER GUIDE Disclaimer We would like to point out that the information contained in this user guide may be subject to alteration, particularly as a result of the constant upgrading of our products. This document does not entail any guarantee on the part of us with respect to technical processes described in the user guide or any product characteristics set out in the user guide.
RAK-120S - User Guide, Rev. 1.0 Intended Use THIS DEVICE AND ASSOCIATED SOFTWARE ARE NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE OR RESALE FOR THE OPERATION OF NUCLEAR FACILITIES, THE NAVIGATION, CONTROL OR COMMUNICATION SYSTEMS FOR AIRCRAFT OR OTHER TRANSPORTATION, AIR TRAFFIC CONTROL, LIFE...
RAK-120S - User Guide, Rev. 1.0 Revision History Revision Brief Description of Changes Date of Issue Author/ Editor Initial Issue 2019-September-03 Terms and Conditions We warrant products in accordance with defined regional warranty periods. For more information about warranty compliance and conformity, and the warranty period in your region, visit our website.
RAK-120S - User Guide, Rev. 1.0 Symbols The following symbols may be used in this user guide DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
RAK-120S – User Guide, Rev. 1.0 For Your Safety Your new product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
RAK-120S - User Guide, Rev. 1.0 Lithium Battery Precautions If your product is equipped with a lithium battery, take the following precautions when replacing the battery. Danger of explosion if the battery is replaced incorrectly. Replace only with same or equivalent battery type recommended by the manufacturer.
RAK-120S - User Guide, Rev. 1.0 Table of Contents Symbols ..........................................6 For Your Safety ........................................7 High Voltage Safety Instructions .................................. 7 Special Handling and Unpacking Instruction ............................7 Lithium Battery Precautions ..................................8 General Instructions on Usage ..................................8 Quality and Environmental Management ..............................
RAK-120S - User Guide, Rev. 1.0 1/ General Safety Instructions for IT Equipment Please read this chapter carefully and take careful note of the instructions, which have been compiled for your safety and to ensure to apply in accordance with intended regulations. If the following general safety instructions are not observed, it could lead to injuries to the operator and/or damage of the product;...
Page 14
RAK-120S - User Guide, Rev. 1.0 Additional safety instructions for DC power supply circuits To guarantee safe operation of devices with DC power supply voltages larger than 60 volts DC or a power consumption larger than 240 VA, please observe that: ...
RAK-120S - User Guide, Rev. 1.0 1.1. Electrostatic Discharge (ESD) A sudden discharge of electrostatic electricity can destroy static-sensitive devices or micro-circuitry. Therefore proper packaging and grounding techniques are necessary precautions to prevent damage. Always take the following precautions: 1. Transport boards in ESD-safe containers such as boxes or bags.
Page 16
RAK-120S - User Guide, Rev. 1.0 Do not dispose of lithium batteries in general trash collection. Dispose of the battery according to the local regulations dealing with the disposal of these special materials, (e.g. to the collecting points for dispose of batteries).
RAK-120S - User Guide, Rev. 1.0 2/ Electromagnetic Compatibility For detailed information refer to section 10.3 “CE Directives and Standards”. 2.1. Electromagnetic Compatibility (EU) This product has been designed for low level of radiated emission for residential, commercial and light industrial environments and high immunity level for industrial environmental.
6. If you notice any shipping damage or inconsistencies between the contents and your order, please contact us for help and information. 3.2. Scope of Delivery 3.2.1. Standard 1x RAK-120S (corresponding to the ordered system configuration) 1x Power cord (plug type depending on country) 1x Quick installation guide 3.2.2.
RAK-120S - User Guide, Rev. 1.0 4/ System Overview The RAK-120S is an embedded server enclosed within a short-depth chassis, offering the superior qualities for operation in the space-saving wall-mount racks or cabinets. It can be optionally factory-equipped with an mPCIe WLAN, Bluetooth or WWAN card for three antennas. Users may choose the implementation of up to four 2.5"...
The baseboard comes with an onboard full-sized mSATA / mPCIe interface connector. The connector can be switched to mSATA or mPCIe setting via the jumper JP1. Users can expand the RAK-120S with mSATA SSD drive, mPCIe WLAN card or mPCIe WWAN modem card.
The storage LED blinks red when data is being written into or read from the HDD / SSD drive. 4.2.4. USB 2.0 The RAK-120S provides two USB 2.0 / 1.1 interfaces on the front I/O panel. These connectors allow connection of USB- compatible devices to the system.
4.3.6. Accessible Bay for PCIe x16 Add-on Card Slot The RAK-120S provides one bay on the rear I/O panel to access the internal PCIe x16 Add-on card slot for network, storage, graphics, video or other functional expansion. The slot supports only x8 signal.
4.4.2. SATA Power Connector & SATA Power Cable The RAK-120S provides six 7-pin SATA 3.0 data connectors (Figure 4, pos. 2), four SATA power cables (Figure 4, pos. 3) and two dual 2.5" HDD / SSD brackets (Figure 4, pos. 7) for installing up to four 2.5" SATA HDDs / SSDs.
RAK-120S - User Guide, Rev. 1.0 5/ Accessing Internal Components This section contains important information that you must read before accessing the internal components. You must follow these procedures properly when installing, removing or handling any board. It is recommended to expand your system with applicable expansion card(s) before it is installed into a rack or cabinet.
1. Close all applications. Shut down the system properly and disconnect the connection to the main power source. Disconnect all peripherals. 2. The RAK-120S should lay on a flat, clean surface with the access cover facing upwards. 3. Loosen the hand-screw knobs (two located on the rear side), that secure the access cover to the chassis.
7. Tighten the hand-screw knobs when the cover is firmly in place.. When used as intended, the RAK-120S is to operate only in closed condition. Only when the access cover is properly fixed with the hand-screw knobs and the rear...
RAK-120S - User Guide, Rev. 1.0 5.1.3. Installing an M.2 SSD To install an M.2 SSD please proceed according to the steps described: 1. Open the device as described in the subsection 5.1 "Opening and Closing the Chassis" (step 1-5).
The applied cooling method provides adequate cooling of the device during operation and performs a one-way thermal transfer to the airflow. There are ventilation holes located on the front and rear sides of the RAK-120S. They provides heat dissipation during operation.
Page 31
RAK-120S - User Guide, Rev. 1.0 When the RAK-120S is extended and configured with third party components like mPCIe / M.2 expansion card(s) and hard drives (HDD or SSD), it has to be taken into account that the air temperature inside the system is higher than the ambient temperature.
Refer also to section 10.1.2 “Mechanical Specifications”. The RAK-120S must be firmly attached to a clean flat and solid mounting surface. Use proper fastening materials suitable for the mounting surface. Ensure that the mounting surface type and the used mounting solution safely support the load of the RAK-120S and the attached components.
RAK-120S configuration with a rackmount kit for horizontal installation into a rack / cabinet. Depending on the ordered RAK-120S configuration, your system may be supplied with a rackmount server slide kit (Figure 8). The kit consists of one piece of left-hand server slide (Figure 8, pos. R), one piece of right-hand server slide (Figure 8, pos.
RAK-120S - User Guide, Rev. 1.0 Press the trigger dowm to release Pull chassis (inner) slide rail out Chassis (inner) slide rail Cabnet (outer) slide rail 2. Mount the chassis (inner) slide rail to the server chassis through the two standoffs located on the chassis and a supplied M4 screw.
RAK-120S - User Guide, Rev. 1.0 Release safety lock before mounting Push the safety lock forward to secure 4. Make sure that the ball retainer is in fully open position. Then insert the chassis (inner) slide rail into the cabinet (outer) slide rail.
RAK-120S - User Guide, Rev. 1.0 Figure 14: Securing the server Cabinet rack rail Center hole Chassis (inner) slide rail Cabinet (outer) slide rail For a sufficient air circulation around the device, we recommend keep a proper clearance and not mount / operate any other devices within the clearance around the RAK-120S.
RAK-120S - User Guide, Rev. 1.0 7.2. AC Power Connection The RAK-120S integrates a power supply unit with the chassis and can be connected by a AC-in power socket (Figure 2, pos. 1) directly to an AC power source. // 37...
10/ “Technical Specifications”. 8.1. Connecting to DC Power Supply The AC-in power socket (Figure 2, pos. 1) is located on the rear side of the RAK-120S. The RAK-120S is supplied with a AC power cord.
Your system can be supplied optionally with a pre-installed operating system. If you have ordered your RAK-120S with a pre-installed operating system, all drivers are installed in accordance with the system configuration ordered (optional hardware components). Your system is fully operational when you switch it on for the first time.
9/ Maintenance and Cleaning Our equipment requires only minimum servicing and maintenance for proper operation. For light soiling, clean the RAK-120S with a dry cloth. Carefully remove dust from the surface of the chassis using a clean, soft brush. ...
RAK-120S - User Guide, Rev. 1.0 10.1. Mechanical Specifications Table 3: Mechanical Specifications Construction 1U Metal Rackmount Chassis Dimensions (W x D x H) 430.4 mm x 400.0 mm x 44.5 mm / 16.94” x 15.75” x 1.75” (without handles) ...
RAK-120S - User Guide, Rev. 1.0 11/ Standard Interfaces – Pin Assignments Low-active signals are indicated by a minus sign. 11.1. AC-in Power Socket Table 6: AC-in Power Socket (see Figure 2, pos. 1) Signal Name AC Connector (female) Live Source (AC 100 V ~ 240 V)
RAK-120S - User Guide, Rev. 1.0 Signal Name 4-pin USB Connector Type A Version 2.0 +USBVCC USB_D- USB_D+ 11.5. VGA Connector Table 10: VGA Connector (see Figure 2, pos. 2) Signal Name 15-pin D-SUB Female Cpnnector Green Blue DDC data...
Supervisor Password (see Security menu), press <RETURN>, and proceed with step 5. 5. A setup menu will appear. The RAK-120S uEFI BIOS setup program uses a hot key-based navigation system. A hot key legend bar is located on the bottom of the setup screens.
RAK-120S - User Guide, Rev. 1.0 12.2. Starting the uEFI BIOS The Setup utility features shows six menus in the selection bar at the top of the screen: Main Advanced Power Boot Security Save & Exit The Setup menus are selected via the left and right arrow keys.
RAK-120S - User Guide, Rev. 1.0 Figure 16: BIOS Main Menu Screen System Data and Time BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Product Information Product Name RAK-120S BIOS Version R1.00 (x64) BIOS Build Date 02/19/2019 ME FW Version 0B:4.0.4.181...
RAK-120S - User Guide, Rev. 1.0 12.2.2. Advanced Setup Menu The Advanced setup menu provides sub-screens and functions for advanced configurations. The following sub- screen functions are included in the menu: LAN Configuration FIA HSIO12 Configuration CPU Chipset Configuration ...
RAK-120S - User Guide, Rev. 1.0 Figure 18: BIOS Advanced Menu - FIA HSIO12 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Flexible I/O Adapter HSIO12 Configuration HSIO12 I/O amount Full Active Lane 8:PCIE-C6139(VGA) [PCIE Enable]...
Page 52
RAK-120S - User Guide, Rev. 1.0 Feature Option Description Lane15:SATA4 [Lane Disabled], Select Lane to work as Disabled / SATA4 [SATA Enable] Lane16:SATA5 [Lane Disabled], Select Lane to work as Disabled / SATA5 [SATA Enable] Lane17:SATA6 [Lane Disabled], Select Lane to work as Disabled / SATA6...
RAK-120S - User Guide, Rev. 1.0 Figure 19: BIOS Advanced Menu - CPU Chipset Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit CPU Chipset Configuration EIST [Enabled] Turbo Mode [Enabled] CPU C State [Enabled] → ←: Select Screen Active Processor Core ↑...
RAK-120S - User Guide, Rev. 1.0 Figure 21: BIOS Advanced Menu - SATA Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit SATA Configuration SATA Controller 0 [Enabled] SATA-0 Port Multiplier [Disabled] SATA Controller 1 [Enabled] SATA-1 Port Multiplier...
RAK-120S - User Guide, Rev. 1.0 Figure 25: BIOS Advanced Menu - Super IO Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super IO Configuration > Serial Port 1 Configuration → ←: Select Screen > Serial Port 2 Configuration ↑...
RAK-120S - User Guide, Rev. 1.0 Feature Option Description 11, 12;] Serial Port 1 Type [RS232], [RS422], Select an appropriate type for Serial Port 1. [RS485] RS485 Duplex Mode [Half Duplex], [Full Select an appropriate RS485 Duplex Mode. Duplex] RS485 Auto Flow [Disabled], [Enabled] Select whether to enable or disable RS485 Auto Flow Control.
RAK-120S - User Guide, Rev. 1.0 Figure 29: BIOS Advanced Menu - Serial Port Console Redirection - COM1 Console Redirection Settings* BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit COM1 Console Redirection Settings Terminal Type [ANSI] Bits per second [115200] →...
Page 63
RAK-120S - User Guide, Rev. 1.0 Feature Option Description Terminal data. Resolution 100x31 [Disabled], [Enabled] Select whether to enable or disable extended terminal resolution. Putty KeyPad [VT100], [LINUX], Select FunctionKey and KeyPad on Putty. [XTERMR6], [SCO], [ESCN], [VT400] // 63...
RAK-120S - User Guide, Rev. 1.0 Figure 30: BIOS Advanced Menu - Serial Port Console Redirection - COM2 Console Redirection Settings* BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit COM2 Console Redirection Settings Terminal Type [ANSI] Bits per second [115200] →...
Page 65
RAK-120S - User Guide, Rev. 1.0 Feature Option Description Terminal data. Resolution 100x31 [Disabled], [Enabled] Select whether to enable or disable extended terminal resolution. Putty KeyPad [VT100], [LINUX], Select FunctionKey and KeyPad on Putty. [XTERMR6], [SCO], [ESCN], [VT400] // 65...
RAK-120S - User Guide, Rev. 1.0 Figure 31: BIOS Advanced Menu - Serial Port Console Redirection - Legacy Console Redirection Settings BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Legacy Console Redirection Settings Redirection COM Port [COM1] →...
RAK-120S - User Guide, Rev. 1.0 Figure 32: BIOS Advanced Menu - Serial Port Console Redirection - Out-of-Band Mgmt Port Console Redirection Settings* BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Out-of-Band Mgmt Port [COM1] Terminal Type...
RAK-120S - User Guide, Rev. 1.0 Figure 33: BIOS Advanced Menu - H/W Monitor BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit PC Health Status CPU Temperature - DTS : +34 C CPU Temperature - Therm : +34 C...
RAK-120S - User Guide, Rev. 1.0 12.2.3. Power Setup Menu The Power setup menu provides functions and a sub-screen for power configurations. The following sub-screen function is included in the menu: WatchDog Timer Configuration Figure 34: BIOS Power Setup Menu...
RAK-120S - User Guide, Rev. 1.0 Feature Option Description Driver], [FW- MagicPacket] ResumeLan I210-AT- [Disabled], [OS- Select whether to enable Wake from LAN Device Intel I210-AT-2. Driver], [FW- MagicPacket] Resume By RTC [Disabled], [Enabled] Select whether to enable or disable Wake Up on Alarm, to turn Alarm on your system on a special day of the month.
RAK-120S - User Guide, Rev. 1.0 12.2.4. Boot Setup Menu The boot setup menu lists the for boot device priority order, that is generated dynamically. Figure 36: BIOS Boot Setup Menu BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit...
The Security setup menu provides information about the passwords and functions for specifying the security settings. The passwords are case-sensitive. The RAK-120S provides no factory-set passwords. If there is already a password installed, the system asks for this first. To clear a password, simply enter nothing and acknowledge by pressing <RETURN>.
Page 74
RAK-120S - User Guide, Rev. 1.0 12.2.5.1. Remember the password It is highly recommended to keep a record of all passwords in a safe place. Forgotten passwords results in being locked out of the system. If the system cannot be booted because the User Password or the Supervisor Password are not know, contact our Technical Support for further assistance.
RAK-120S - User Guide, Rev. 1.0 12.2.6. Save & Exit Setup Menu The exit setup menu provides functions for handling changes made to the UEFI BIOS settings and the exiting of the setup program. Figure 39: BIOS Save & Exit Setup Menu...
RAK-120S - User Guide, Rev. 1.0 Appendix A: List of Acronyms The following table does not contain the complete acronyms used in signal names, signal type definitions or similar. A description of the signals is included in the I/O Connector and Internal connector chapters within this user guide.