Install Additional Temperature Cables And Mark The Cables For The "Ubg-16; Appendix A - Adding A Temperature Probe To The Ubg-16 - Electronics International UBG-16 Installation Instructions Manual

11. 11. 11. Install Additional Temperature Cables and Mark The Cables Install Additional Temperature Cables and Mark The Cables Install Additional Temperature Cables and Mark The Cables
11. 11. Install Additional Temperature Cables and Mark The Cables Install Additional Temperature Cables and Mark The Cables
for the "UBG-16" for the for the "UBG-16" "UBG-16" "UBG-16" "UBG-16"
for the for the
There are two identical pre-wired Extension Cable Harnesses in the installation kit. One end of
each harness has a 16-pin Circular Connector and the other end has red Slip-on connectors on the
individual extension cables (see the Wiring Diagram at the back of this manual). There is a type K
thermocouple extension cable for each EGT and CHT temperature to be measured. The end of
each extension cable in the harness has a piece of yellow heat shrink marked with its channel
number. One of these harnesses is to be connected to the EGT probes (and LEFT connector on the
UBG-16) and the other is to be connected to the CHT probes (and the RIGHT connector on the
UBG-16). Refer to step 4 (Configuration Form) to identify which harness will be used for EGT's
and which will be used for CHT's.
Mark the Circular Connector that will be connected to the EGT probes. The first 4 or 6 channels
(starting with channel #1) are used to monitor EGT's. Any additional channels may be used to
monitor other temperatures or functions. There are 8 channels available on each 16-pin Circular
Connector. Any channel used to measure a temperature other than EGT or CHT (TIT, OAT,
Carb Temp, etc.) will have a type K thermocouple extension cable lose in the kit. Plug any addi-
tional extension cables into the appropriate pins of the Circular Connector (see "Appendix A" at
the back of this manual).
Any channel used to monitor functions other than temperature (RPM, M.P., Oil Pressure, Volts,
Amps, etc.) will require a Functional Module. Installation of a Functional Module will be covered
later in this manual.
Mark each of the Type K thermocouple extension cables in this harness (on the yellow heat shrink)
with the temperature function for which it will be used (i.e., CHT, EGT, Oil, etc.). An ink pen or
marker works well.
Note: If a cable needs to be removed from a connector, you must Note: Note: Note: Note:
tool may be purchased from E.I.
Mark the Circular Connector that will be connected to the CHT probes. The first 4 or 6 channels
(starting with channel #1) are used to monitor CHT's. Any additional channels may be used to
monitor other functions. There are 8 channels available on each 16-pin Circular Connector. Any
channel used to measure a temperature other than EGT or CHT (TIT, OAT, Carb Temp, etc.)
will have a type K thermocouple extension cable lose in the kit. Plug any additional extension
cables into the appropriate pins of the Circular Connector (see "Appendix A" at the back of this
manual).
Any channel used to monitor a function other than temperature (RPM, M.P., Oil Pressure, Volts,
Amps, etc.) will require a Functional Module. Installation of a Functional Module will be covered
later in this manual.
Mark each of the Type K thermocouple extension cables in this harness (on the yellow heat shrink)
with the temperature function for which it will be used (i.e., CHT, EGT, Oil, etc.). An ink pen or
marker works well.
Note: Note:
Note: Note: Any channel will accept any one of E.I.'s probes or Functional Module. Note:
must use an extraction tool. This must must must
8