Subscribe to Our Youtube Channel
Related Manuals for Parker AEGCTM-2
Summary of Contents for Parker AEGCTM-2
- Page 1 MODELS: AEGCTM-2 AEGCTM-2G AEGCTM-2E-CE AEGCTM-2E-CEG AEGCTM-2WOH AEGCTM-2EWOH-CE Coning and Threading Machine Operation and Maintenance Manual Catalog: 02-9221ME April 2014...
-
Page 2: Table Of Contents
AEGCTM-2, Auxiliary Views & Parts List ........... 15 Sheet 3 Oil Heater Option (AEGCTM-2WOH) & Alphabetical Parts List (AEGCTM-2) ......16 Sheet 4 AEGCTM-2E-CE, 220 VAC, Views . -
Page 3: Safety And Operating Environment
Note: All caster wheels have locks to prevent movement EN60204-1. of machine during operation. Remove plastic restraining straps securing the yoke assemblies. Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 4: Tubing Preparation
+ (2 x 1/16" Finish Allowance) Cut Length Determine the appropriate sized cutting blades using Table #5 and the outside and inside diameters Figure 2 of the tubing. Determine Tube Length Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 5: Installing Coning Blades
Coning Blades: Part Number is facing out Note: Tubing must be straight for at least 4.75 in. (121 mm) in order to be able to secure the tubing in the collet for coning. Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 6: Illustration Of Coning Operation
Reverse the feedwheel until the tubing is disengaged from the cutting blades. Attach the chained hook to the feedwheel and if no one is using the threading end of the machine, turn it off. Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 7: Threading Operation
4. It is critical that the numbered chaser is placed into the matching numbered slot. For example, No. 1 chaser in No. 1 slot, No. 2 chaser in No. 2 slot, etc. Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 8: Moving Die Head To Extreme Position For Chaser Insertion By Pressing Head Release Lever
5.4.2 If the piece does not go in smoothly, loosen adjusting ring the cone of the tube touches the chasers. binding screw using a 5/32" allen wrench (Figure #5). Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 9: Setting Thread Length. Die Head Is Shown In The Closed Position
Tighten the outer collet nut with spanner Note: Plug or cap the free end of tubing not being coned wrench. or threaded to prevent cuttiing oil from spilling onto the ground. Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 10: Assembly And Make Up
CAUTION: Unplug the machine before proceeding. Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 11: Completed Medium Pressure Connection
1-3/16 75 (101.6) F562C40 1-3/16 60 (81.4) SF1000C30 1-3/8 150 (203.3) F1000C43 1-3/8 180 (244.0) Figure 13 Completed Medium Pressure Connection Figure 14 Completed High Pressure Connection Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... -
Page 12: Recommended Spare Parts
Section 7.0 Recommended Spare Parts Recommended parts and tooling for all variations of Coning and Threading Machine Models AEGCTM-2 and AEGCTM-2E. Drive Belt: for the AEGCTM-2E-CE, p/n P-6958-1 Coning & Threading Gage for the AEGCTM-2, p/n P-1754-2 Other Tooling: See Table 5. -
Page 13: View Of Pump Face
IF FOR ANY REASON THESE OPERATIONS DO NOT If for any reason the oil heater fails to operate properly RESTORE THE PUMP TO FULL SERVICE, CONTACT THE contact the factory for inspections. Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME... - Page 14 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 15 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 16 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 17 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 18 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 19 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 20 OIL SPLASH GUARD PARTS LIST: KIT PART NUMBER - AEGCTM-2GK Item DESCRIPTION PART NUMBER QTY. Oil Guard 90598 Screw 90596 Lockwasher, Spring, 1/4, Regular P-3701 Bracket, Oil Guard 191F-3394 Screw 90597 Lockwasher, Spring, 5/16, Regular P-0841 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 21 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 22 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 23 Parker Autoclave Engineers Instrumentation Products Division Erie, PA USA www.autoclave.com | Cat. 02-9221ME...
- Page 24 Offer of Sale The items described in this document are available for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. Any sale contract entered by Parker will be governed by the provisions stated in Parker's standard terms and conditions of sale (copy available upon request).
Need help?
Do you have a question about the AEGCTM-2 and is the answer not in the manual?
Questions and answers