Advertisement
Available languages
Available languages
Convector control
Description (Fig. 6)
ON/OFF switch
Position "0" — heating off
Position "1" — heating on
A thermostat control knob enables set-
ting from the position * (antifreezing tem-
perature) to the position 8.
Setting and blocking
the thermostat knob
(Fig. 6)
Limiting the thermostat movement to a
maximum selected value:
• Set the knob scale on the selected
value so that it is against the control
box indicator.
• Remove one of two latches situated
under the cable clip.
• Insert the latch into the thermostat
knob to the right, close to the value
selected on the scale.
Limiting the thermostat movement to a
minimum selected value:
• Set the thermostat scale so that the
maximum selected value is against the control box indicator.
• Remove one of two latches situated under the cable clip.
• Insert the latch into the thermostat knob to the left, close to the value selected
on the scale.
Blocking the thermostat movement:
• Set the thermostat scale so that it corresponds to the selected value.
• Remove both latches situated under the cable clip.
• Insert the latches into the thermostat knob, from both sides of the value
selected on the scale.
Calibration
To achieve trouble-free temperature control, the thermostat must be set as described
below. Situate a thermometer in the centre of the room, 1.2 m above the floor (with
doors and windows closed). Set the ON/OFF switch to the position "1". Set the
thermostat knob to the maximum position. As soon as the required room tempera-
ture is achieved, e.g. the thermometer indicates 20 °C, slowly turn back the thermo-
stat control knob until the thermostat is off (a click can be heard). After the temperature
has been set, the thermostat will automatically keep the room temperature constant
by successively switching on and off the power supply to the unit.
Switch off
To switch off the convector without acting on the thermostat setting, set the
ON/OFF switch to position "0".
Removing the convector
Before removing the convector from its mounting bracket set the ON/OFF switch
to position "0". If an external pilot wire is used, cut off its power supply too. Use a
screwdriver to release the mounting bracket locks. Disconnect the power supply
cable from the wall junction box. Lift the convector vertically to release it from the
bracket.
Notice
Any interventions in the convector should only be made by a qualified person.
Disconnect the convector from the power supply before starting such work. If the
convector is controlled by a pilot wire, make sure that the power supply cable and
the pilot wire are disconnected before starting work.
Vapours with a moderate smell are released during the first use of the convector for
a short time. It does not repeat during further use.
Economic operation
Switch off convectors if you ventilate rooms for a long period of time. Whenever
you do not use a room (e.g. a guest room) or the whole house for any extended
period of time (holiday), set the thermostat knob to the position *. The room
temperature will then be automatically kept on the value of approx. 7 °C.
Fig. 6
FENIX TRADING s. r. o.
e-mail: fenix@fenixgroup. cz • www. fenixgroup. cz
Important safety instructions
Do not cover the convector in any way. The "DO NOT COVER" warning is there
to remind you that any material covering the unit can catch fire. Never place or
hang any furniture or curtains in front of the convector, see Fig. 7. Ensure a free air
circulation. Clean the inlet and outlet grid from dust regularly, at least each time
before starting a heating season.
Mount the convectors on C1 & C2 combustibility class materials.
Fig. 7
Technical data
y T
e p
E
C
O
L F
X E
0
5
E
C
O
L F
X E
0
7
E
C
O
L F
X E
1
0
E
C
O
L F
X E
2 1
E
C
O
L F
X E
5 1
E
C
O
L F
X E
7 1
E
C
O
L F
X E
2
0
E
C
O
L F
X E
2
5
Guarantee conditions
Supplier grants a 24-month guarantee from the date of sale. The guarantee does
not cover defects caused during transport, due to negligent manipulation, or faulty
installation. The guarantee dos not cover normal wear and tear of product.
Confirmation of sale: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date of sale: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Production number: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seller:
Slezská 2, 790 01 Jeseník, Tel. : 584 495 441, Fax: 584 495 431
Fig. 8
O
u
p t
t u
o V
a t l
e g
D
m i
e
(
W
)
(
) V
e L
g n
h t
5
0
0
2
8
0
7
5
0
3
6
0
1
0
0
0
4
4
0
/ 1
N
2 1
5
0
5
2
0
2
3
0
V
5 1
0
0
6
0
0
5
0
H
z
7 1
5
0
6 7
0
2
0
0
0
8
4
0
2
5
0
0
1
0
0
0
s n
o i
s n
m (
) m
W
e
g i
t h
H
e
g i
t h
D
p e
h t
k (
) g
4
0
0
8
0
3
7 ,
4
0
0
8
0
3
7 ,
4
0
0
8
0
4
2 ,
4
0
0
8
0
4
9 ,
4
0
0
8
0
5
5 ,
4
0
0
8
0
6
1 ,
4
0
0
8
0
6
8 ,
4
0
0
8
0
9
0 ,
Advertisement
Need help?
Do you have a question about the ECOFLEX SL Series and is the answer not in the manual?
Questions and answers