Strobe Light Level Adjustment; Strobe White Balance Adjustment & Check - Sony DCR-IP45 Service Manual

DCR-IP45/IP45E/IP55/IP55E

15. Strobe Light Level Adjustment

Adjust the light level when the strobe light flashes.
Subject
Measurement Point
Measuring Instrument
Adjustment Page
Adjustment Address
Specified Value
Note1: Background paper (J-250-130-A). Perform this adjustment in the
dark room or use a dark box.
Note2: Any light other than the strobe light should not light up the paper.
Note3: This adjustment should be carried out upon completion of "HALL
Adjustment" , "Flange Back Adjustment".
Note4: The data of page: 0, address: 10 must be "00".
Note5: Check that the data of page: 6, address: 02 is "00". If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) POWER .................................................................. CAMERA
2) FLASH ......................................................................... OPEN
(Press FLASH ( ) button and set to the forced flash mode ( ),
and press PHOTO button.)
3) NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data
1 0 01
2 7 05
3 6 01
4
5 6 02
6 6 B8
Note6: Use the STOP button of the adjustment remote commander.
Note7: The adjustment data will be automatically input to page: F, address:
8C to 91.
Processing after Completing Adjustments:
Order Page Address Data
1 6 01
2 7 05
3 0 01
2mm
Paper which reflection rate is 18%
(50cm from the front of the lens) (Note1)
Adjustment remote commander
F
8C to 91
Data of page: 6, address: B8 is "00".
Procedure
01 Set the data.
04 Set the data. (Note6)
67 Set the data, and press PAUSE
button.
Check the flashing.
Check that the data is "01".
(Note7)
Check that the data is "00".
Procedure
00 Set the data, and press PAUSE
button.
00 Set the data.
00 Set the data.
2mm
R-Y
B-Y
Fig. 5-1-13.
16. Strobe White Balance Adjustment & Check
Adjust and check the white balance when the strobe light flashes.
Subject
Measurement Point
Measuring Instrument
Adjustment Page
Adjustment Address
Specified Value
Note1: Background paper (J-250-130-A). Perform this adjustment in the
dark room or use a dark box.
Note2: Any light other than the strobe light should not light up the paper.
Note3: This adjustment should be carried out upon completion of "HALL
Adjustment", "Flange Back Adjustment", "Auto White Balance
& LV Standard Data Input", "Auto White Balance Adjustment",
"Strobe Light Level Adjustment"
Note4: The data of page: 0, address: 10 must be "00".
Note5: Check that the data of page: 6, address: 02 is "00". If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) POWER .................................................................. CAMERA
2) FLASH ......................................................................... OPEN
(Press FLASH ( ) button and set to the forced flash mode ( ),
and press PHOTO button.)
3) NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data
1 0 01
2 7 05
3 6 01
4
5 6 02
6 6 02
7 6 01
8
9 6 02
10
11
Note6: Use the STOP button of the adjustment remote commander.
Note7: The adjustment data will be automatically input to page: F, address:
3E, 3F.
Processing after Completing Adjustments:
Order Page Address Data
1 6 01
2 7 05
3 0 01
5-30
Paper which reflection rate is 18%
(50cm from the front of the lens)
(Note1)
Video output terminal
Vectorscope
F
3E, 3F
Fig. 5-1-13.
Procedure
01 Set the data.
04 Set the data. (Note6)
B9 Set the data, and press PAUSE
button.
Check the flashing.
Check that the data is "01".
(Note7)
00 Set the data.
E7 Set the data, and press PAUSE
button.
Check the flashing.
Check that the data is "01".
Wait for 3 sec.
Check that the center of the
white luminance point is within
the circle shown Fig. 5-1-13.
Procedure
00 Set the data, and press PAUSE
button.
00 Set the data.
00 Set the data.