Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intense Primer 29 2019
Summary of Contents for Intense Primer 29 2019
- Page 1 user manual // p r i m e r 2 9...
-
Page 2: Table Of Contents
Exploded View and B.O.M. worked alone in his garage to today, where a crew of talented people work in a Temecula, CA factory, Intense has been a brand built on passion by Assembly forward thinkers who, even today, love nothing more than to throw a leg Frame Assembly over a sweet bike and head out for a rip. -
Page 3: Getting To Know Your Primer
getting to Component spec // Geometry // • Fork: FOX 34 150 mm with 51 • Bottom Bracket: Threaded 73 mm BB Drop know your g e o m e t r y N O T e mm fork offset, 557 mm axle •... -
Page 4: Exploded View And B.o
ITEM PART ITEM PART exploded view and b.o.m. // ITEM DESCRIPTION QTY. TORQUE SPEC. ITEM DESCRIPTION QTY. TORQUE SPEC. NUMBER NUMBER 11 Nm / Water Bottle Bolt, 2 Nm / Hanger Bolt 130798 Derailleur Hanger Bolt BHCS M5 x 12 410010 100 in-lbs Button Head, M5 x 12... -
Page 5: Assembly
Service and maintenance on an Intense bicycle requires special tools, abilities and knowledge of working on bicycles. It is always recommended to use an authorized Intense dealer for service and maintenance. Always wear eye protection. It is critical to use the proper tools, loctite, grease and torque specs during assembly. - Page 6 C O N N e C T i N G T H e L O W e r L i N K T O F r O N T T r i A N G L e // C O N N e C T i N G r e A r T r i A N G L e T O L O W e r L i N K // Apply grease to the two pivot axle spacers Match link to front triangle and from non drive Use 5 mm HEX to install shoulder bolt...
- Page 7 C O N N e C T i N G r e A r T r i A N G L e T O T O p L i N K // i N S T A L L i N G r e A r S H O C K // Put a small dab of grease on the outside Insert non-drive D-lock reducer Flip Chip Install upper link spacer (#130821) on the...
- Page 8 i N S T A L L i N G D e r A i L L e U r H A N G e r // r e A r A X L e // S e A T C L A m p // Grease portion of derailleur Torque derailleur bolt (#130798) Grease and install adjuster...
-
Page 9: Torque Specifications
• small ruler or measuring device 14 Nm / 125 in-lbs • torque wrench • Intense Carbon Paste torque specifications // Achieving proper torque is vital to ensuring the Before insertion, liberally coat the seat post with carbon paste and gently safe performance and function of the Primer 29 slide into the seat tube. -
Page 10: Setting The Sag
setting the sag // shock setup // Release compression. Travel Low Setting: 140 mm (5.5 inch) Measure gap from 1. Remove fork and shock air caps and be sure you have a o-ring to seal lip. Lower Setting: 137 mm (5.4 inch) Travel While suspension shock pump and a small ruler or measuring device handy. - Page 11 Flip Chip: lOW and lOWer settings // The Low (Image #1) and Lower (Image #2) settings of the Flip Chip allows you to optimize the performance characteristics of the Primer 29 by altering the frame's geometry. In general, the Lower setting results in a more 'slack' geometry with a decreased head tube angle, lower BB height as well as a lower standover height.
-
Page 12: Maintenance
Disassemble stem, headset and fork. Check bearings for Headset qualified Intense Cycles dealer. Any direct impact to the frame can pitting and wear cause serious structural damage. - Page 13 www.InTenseCYCles.com p h o n e : + 1 ( 9 5 1 ) - 3 0 7 - 9 2 1 1 C u s t o m e r S e r v i c e : t e c h c e n t e r @ i n t e n s e c y c l e s . c o m G e n e r a l i n f o : i n f o @ i n t e n s e c y c l e s .
Need help?
Do you have a question about the Primer 29 2019 and is the answer not in the manual?
Questions and answers