SunStar Fortuna 5 Series User Manual page 64

※ This item is operated by the factory only, so general users and A/S technicians should not use it.
No.
30 OUTPUT00 (B/T Solenoid)
31 OUTPUT01 (P/F Solenoid)
32 OUTPUT02 (T/T Solenoid)
33 OUTPUT03 (W/P Solenoid)
34 OUTPUT04 (T/R Solenoid)
35 OUTPUT05 (Left Solenoid)
36 OUTPUT06 (Right Solenoid)
37 OUTPUT07 (AUX Solenoid)
38 OUTPUT10 (Left LED)
39 OUTPUT11 (Right LED)
40 OUTPUT12 (Needle upper stop notifying signal)
41 OUTPUT13 (Needle lower stop notifying signal)
42 OUTPUT14 (Signal notifying motor is running)
43 OUTPUT15 (Signal notifying target has been reached)
★ A : Output PIN function
Functi o n No. H/W type actual output name
0 B/T Solenoid
1 P/F Solenoid
2 T/T Solenoid
3 W/P Solenoid
4 T/R Solenoid
5 Left Solenoid
6 Right Solenoid
7 AUX Solenoid
8 Left LED
9 Right LED
"Needle Up-stop " notifying signal
10
"Needle Down-stop" notifying signal
11
"Sewing machine running" notifying signal
12
"Target speed" notifying signal
13
14 "Trimming" notifying signal
15 "End Back Tack" notifying signal
16 "Emergency stop" notifiying signal
- A signal appears when the motor stops for any error.
17 Roller Lift Solenoid
18 Hemming Device Output
"First step forward pedal" notifying signal
19
200 Low signal
※ If an output signal has been sent twice in the OUTPUT00~OUTPUT15 output pin, the same signal will appear in two different output pins.
Ex) if OUTPUT00 = 0 & OUTPUT03 = 0, then B/T signal is output from both OUTPUT00 & OUTPUT03 pin
※ When setting up other functions apart from the function numbers listed above, the pertinent output pin functions are disregarded.
※ Roller Lift Solenoid = Presser Foot-Lift solenoid + Back Tack solenoid + Roller Lift Switch
43~ NOT USED
49 NOT USED
If the specific items of the parameter are changed carelessly, they could break down or damage the machine, so the
user must be well-trained before using it.
Caution
64
Function
: Low Active
: Low Active
: Low Active
: Low Active
: Low Active
: Low Active
: Low Active
: Low Active
: High Active
: High Active
: High Active
: High Active
: High Active
: High Active
Functi o n No.
(with duty) 100
(with duty) 101
(with duty) 102
(with duty) 103
(with duty) 104
(with duty) 105
(with duty) 106
(with duty) 107
(with duty) 108
(with duty) 109
(with duty) 110
(with duty) 111
(with duty) 112
(with duty) 113
(without duty) 114
(without duty) 115
(without duty) 116
(without duty) 117
(without duty) 118
(without duty) 119
(without duty) 201
Initial value
0(Fixed)
1(Fixed)
2
3
4
5 ※ Output port changing function
- write the function number on
6
the output PIN you want to
7
change after referring to the
8 table below
9
10
11
12
13
H/W type actual output name
inv. B/T Solenoid
inv. P/F Solenoid
inv. T/T Solenoid
inv. W/P Solenoid
inv. T/R Solenoid
inv. Left Solenoid
inv. Right Solenoid
inv. AUX Solenoid
inv. Left LED
inv. Right LED
inv. Needle Up-Stopped
inv. Needle Down-Stopped
inv. Motor Running
inv. Target Speed
inv. Trimming
inv. End Back Tack
inv. Emergency Stopped
-A signal appears when the motor stops for any error
inv. Roller Lift Solenoid
inv. Hemming Device Output
inv. Pedal Start
High signal
Step
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(with duty)
(without duty)
(without duty)
(without duty)
(without duty)
(without duty)
(without duty)
(without duty)