Table of Contents
Advertisement
No.
26
Selection of B/T Solenoid operation position
27
Setting the maximum sewing speed of the machine according to
presser foot-lift height of the KM-1060BL sewing machine.
28
Needle bar's automatic stop at the highest position
29
Pedal analog filtering difference
30
When using an angle 2-needle, select the semi-automatic corner operation
31
Speed when selecting a semi-automatic corner
(parameter used only when used after selecting number 30)
32
After selecting the left needle the first sewing stitch
(parameter used only when used after selecting number 30)
33
After selecting the left needle the second sewing stitch
(parameter used only when used after selecting number 30)
34
After selecting the right needle the first sewing stitch
(parameter used only when used after selecting number 30)
35
After selecting the right needle the second sewing stitch
(parameter used only when used after selecting number 30)
36
Maintaining time for the left/right needle solenoid
(After the programmed time the solenoid is automatically released)
37
NOT USED
38
NOT USED
39
Stopping function during AUTO mode and while pedal is neutral
40
Selection of type of N-stitch Sensor
41
The number of stitches done after the N-stitch Sensor has finished sensing.
(After sensing, it will sew the programmed number of stitches and stop)
42
N-stitch sewing speed
43
Selection of One Touch function → replaced by AUTO Key function
(Used in the sewing mode that uses the auto function)
44
Selection of One Touch function → replaced by AUTO sewing mode programming
(If there is no thread trimming signal when selected, sewing will continue even if user releases pedal)
One-Shot sewing speed → When using AUTO function, it is programmed with the speed Up/Dn Key
45
N-stitch sewing mode selection → a sewing mode that inputs a sensor signal
46
in the edge sensor port and uses it as an edge sensor
47
Selection of pre-stitch function (When selected it will perform only
the programmed stitches before the actual sewing work starts)
48
Pre-stitch number of stitches
49
Pre-stitch speed
50
Selection of start B/T operating conditions
( 0 : if pedal is released during back tack, it will stop)
( 1 : if pedal is released during back tack, the work will still be completed)
( 2 : it will perform the exact amount of back tack stitches)
51
Selection of end back tack performance condition
(It will perform the exact amount of stitches for end back tack )
52
Back tack initial first stitch speed during back tack exact performance
If the specific items of the parameter are changed carelessly, they could break down or damage the machine, so the
user must be well-trained before using it.
Caution
Function
Initial value
Range
0
0/1
program P1xx → P2xx → P3xx
?
?
Less than P1xx:3500[spm]
Less than P2xx:3000[spm]
Less than P3xx:2500[spm]
More than P3xx: A20[spm]
0
0/1
15
1~200
0
0/1
1=selection of semi-automatic
200spm
20~2000
3 stitches
0~255
3 stitches
0~255
3 stitches
0~255
3 stitches
0~255
450×0.1sec
50~1000
1
0/1
0
0：active high
3 stitches
0~255
1000spm
20~2000
0
0/1
0
0/1
1=One-Shot Mode
2000spm
40~9960
0
0/1
0
0/1
3 stitches
0~255
2000spm
20~2000
0 : B/T stop function selected
1
1 : B/T work completion
2 : B/T exact stitch performance
0
0/1
1= exact stitch performance
200spm
20~1000
10spm
Step
0= lower position
1= upper position
in order
1
10spm
1 stitch
1 stitch
1 stitch
1 stitch
0.5sec
0=does not stop
1=stops
1：active low
1 stitch
10spm
1=Auto Mode
40spm
1=N-stitch Mode
1=selection
1 stitch
10spm
57
Hide quick links:
Advertisement
Table of Contents
