SunStar Fortuna 5 Series User Manual page 59

(2) Group B Parameter : All types of output, Full-on Time/PWM Duty, checking input/output operations, sewing
machine models and thread trimming sequence programming.
※ These are functions not used by general users and must be regulated by an A/S technician.
No.
1 Back Tack Solenoid Initial Full On Time
2 Presser Foot-Lift Solenoid Initial Full On Time
3 T/T Solenoid Initial Full On Time
4 Wiper Solenoid Initial Full On Time
5 Tension Release Solenoid Initial Full On Time
6 Left Solenoid Initial Full On Time (For Twin Needle)
7 Right Solenoid Initial Full On Time (For Twin Needle)
8 Auxiliary Solenoid Initial Full On Time
9 Left LED Initial Full On Time (For Twin Needle)
10 Right LED Initial Full On Time (For Twin Needle)
11 Needle plate up-stop signal Initial Full On Time
12 Needle plate down-stop signal Initial Full On Time
13 Signal notifying motor running Full On Time
14 Signal notifying target speed achieved Full On Time
15 Back Tack Solenoid Duty Ratio
16 Presser Foot-Lift Solenoid Duty Ratio
17 Thread Trimming Solenoid Duty Ratio
18 Wiper Solenoid Duty Ratio
19 Tension Release Solenoid Duty Ratio
20 Left Solenoid Duty Ratio (For Twin Needle)
21 Right Solenoid Duty Ratio (For Twin Needle)
22 Aux Solenoid Duty Ratio
23 Left LED Duty Ratio (For Twin Needle)
24 Right LED Duty Ratio (For Twin Needle)
25 Signal for up stopping needle Duty Ratio
26 Signal for low stopping needle Duty Ratio
27 Signal notifying motor running Duty Ratio
28 Signal notifying target speed reached Duty Ratio
29 NOT USED
30 Start Back Tack A number of stitches correction value
31 Start Back Tack B number of stitches correction value
32 End Back Tack C stitch correction value
33 End Back Tack D stitch correction value
34 Selection for maintaining reverse solenoid movement when thread trimming (C Only B/T)
35 Programming count condition
(program whether or not automatic counter will be operated)
When automatically counting, select Up/Down count after thread
36
trimming (thread trimming function must be enabled)
37 When count in completeded, the next operation is programmed
38 When count is completed, select the counter auto clear/preset
39 NOT USED
※ Items No. 30~33 : These are the items that make the number of stitches match when back tack number of stitches do not match.
※ Solenoid Duty Ratio : The power that holds and maintains the solenoid.
Solenoid initial full on time : The time it takes to pull the solenoid to the maximum in the outset.
If the specific items of the parameter are changed carelessly, they could break down or damage the machine, so the
user must be well-trained before using it.
Caution
Function Initial value Range
1020ms 4~1020
200ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
100ms 4~1020
50% 0~100
20% 0~100
100 0~100
100 0~100
100 0~100
50 0~100
50 0~100
100 0~100
100 0~100
100 0~100
100 0~100
100 0~100
100 0~100
100 0~100
00.30 6~6
00.30 6~6
00.40 6~6
00.40 6~6
0 0/1 1=reverse direction maintained
0 0/1 0=counter used
1=automatic counter after thread trimming
1 0/1
0=DOWN COUNT
0=buzzer rings, sewing is allowed
1=buzzer rings, sewing is not allowed
0 0/1/2
(If you press the Prog Key, set up is cancelled)
2=No buzzer ring, sewing is allowed
0 0/1
CLEAR/PRESET
Step
4ms
4ms
4ms
4ms
4ms
4ms
4ms
4ms
4ms
4ms
4ms
4ms
4ms
4ms
10%
10
10
10
10
10
10
10
10
10
10
10
10
10
0.05 Stitch
0.05 Stitch
0.05 Stitch
0.05 Stitch
1=Up COUNT
1=AUTO
59