Page 1 Points out hazards or unsafe practices that could cause minor the operation of your vehicle. personal injury or damage to your vehicle. Please note that this manual applies to all GALANT models You will see another important symbol: and explains all features including options. Some features NOTE Gives helpful information.
Page 2: Table Of Contents
Table of contents Overview Quick index General information Seat and restraint systems Features and controls Driving safety Comfort controls For emergencies Vehicle care and maintenance Customer assistance/ Reporting Safety Defects Specifications...
Page 3 Overview Instruments and controls N00100201202 Instrument cluster Combination headlights and P.3-72 dimmer switch P.3-81 Steering wheel remote Turn signal lever P.3-84 control switch (if so equipped) P.5-62 Supplemental restraint Wiper and washer system - air bag switch P.3-87 (for driver’s seat) P.2-38 Horn switch P.3-91 Ignition switch P.3-34 Cruise control lever...
Page 4 Overview Selector lever P.3-39 Supplemental restraint system - air bag (for front passenger’s seat) P.2-38 Heated seat switch Parking brake lever (if so equipped) P.3-28 P.2-10 Floor console box/ Tissue holder/Pen holders Glove compartment P.3-132 P.3-131 Auxiliary Audio connector* P.5-60 Trunk lid release lever P.3-16 Power outlet P.3-122...
Page 5 Overview Center panel N00100700141 Passenger’s air bag off indicator P.2-46 Vents P.5-2 Front passenger seat belt warning light P.2-21 Audio system P.5-24, 5-37 Hazard warning flasher switch P.3-85 Electric rear window defogger switch P.3-90 Air conditioning P.5-5, 5-13...
Page 6 Overview Interior N00100301014 Sunroof switch ® Hands-free Bluetooth cellular Outside rearview mirror switch P.3-32 (if so equipped) phone interface system with voice P.3-26 recognition (if so equipped) P.3-92 Reading lights P.3-128, 7-46, Inside rearview mirror 7-59 Power window switch P.3-23 P.3-30 ®...
Page 7 Overview Trunk area N00100400252 Jack P.6-8 Luggage hooks Luggage hooks P.3-134 P.3-134 Spare tire P.6-10 Inside emergency trunk lid release handle Tools P.6-8 P.3-18...
Page 8 Overview Outside N00100601222 Windshield wiper and washer P.3-87 Outside rearview mirrors P.3-32 Engine compartment P.7-6 Fuel tank filler door P.1-4 Engine hood P.7-4 Locking and unlocking P.3-12 Keyless entry system P.3-7 Front fog lights (if so equipped) P.3-86, 7-45, 7-51 Front side-marker lights P.3-81, 7-45, 7-50 Headlights...
Page 9 Overview Satellite radio antenna (if so equipped) P.5-71 Back-up lights P.7-45, 7-54 Rear-view camera (if so equipped) Antenna P.5-71 P.3-69 Tail and stop lights High-mounted stop light P.3-81, 7-45, 7-53 P.7-45, 7-56 Rear side-maker lights P.3-81, 7-45, 7-53 Trunk lid P.3-16 Tire inflation pressure P.7-23 Changing tires P.6-9 Tire rotation P.7-25...
Page 10 If the light comes on while the engine oil level is normal, have the system P.3-80 checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. Oil pressure warning light If this light comes on while driving, check to see that the parking brake is fully released.
Page 11 Idle the engine until the “N” indicator goes off. If the indicator does not go P.3-42 off, have the system checked at an authorized Mitsubishi Motors dealer or a “N” indicator in the instrument repair facility of your choice as soon as possible.
Page 12 Restart the engine and check to see if the indicator comes on again. If the indicator does not go out, or if it comes on again, have your vehicle inspected at an authorized Mitsubishi Motors dealer or a repair facility of P.3-54 your choice as soon as possible.
Page 13 Quick index If you hear this sound... N00200800648 Sound Do this Ref. page “Key reminder buzzer” A tone will sound if the driver’s door is opened while the ignition key is in the P.3-14 “LOCK” or “ACC” position. Remove the key to stop the tone. Constant tone when the driver’s door is “Headlight reminder buzzer”...
Page 14 The brake pads are worn down to the serviceable limit. P.3-48 brake pedal while driving. Have the brake pads replaced at an authorized Mitsubishi Motors dealer or a repair facility of your choice. “Seat belt reminder buzzer” When the ignition key is turned to the “ON” position, the tone will sound for about 6 seconds.
Page 15 Quick index If this problem occurs... N00200900694 Problem Do this Ref. Page Cannot turn the key. From “LOCK” to “ACC” Turn the key while jogging the steering wheel in either direction. P.3-34, From “ACC” to “LOCK” 3-36 Check the position of the selector lever. The key cannot be removed unless the selector lever is set to the “P”...
Page 16 Quick index Problem Do this Ref. page The engine coolant tempera- ture gauge indicator is at the “H” (hot) position. Steam comes out of the engine compartment. The engine is overheated. P.6-5 Carefully stop the vehicle in a safe place. The vehicle is stuck in sand, Move the selector lever rhythmically between “Sports Mode”...
Page 17 P.4-6 water. There may be a problem in the automatic transaxle. The automatic transaxle does Have the vehicle inspected by an authorized Mitsubishi Motors dealer or a repair facility not shift when accelerating of your choice. P.3-45 and/or the vehicle does not Shift the lever into 2nd gear of the sports mode when starting the vehicle.
Page 18: General Information
Modification of your vehicle ....1- Mitsubishi Motors genuine parts ....1- California Perchlorate Materials Requirements. . .1-...
Page 19: Fuel Selection
Detergent gasoline helps Mitsubishi Motors Corporation strongly supports the use of keep your engine in tune and your emission-control system reformulated gasoline. Properly blended reformulated gasoline working properly.
Page 20 If this happens, contact an authorized Repeatedly driving short distances at low speeds can Mitsubishi Motors dealer or a repair facility of your choice for cause deposits to form in the fuel system and engine, assistance.
Page 21: Filling The Fuel Tank
General information Filling the fuel tank Fuel tank capacity 17.7 gal (67 L) N00301100883 Refueling WARNING 1. Before filling with fuel, stop the engine. Gasoline is highly flammable and explosive. You 2. The fuel tank filler is located on the rear driver side of could be burned, seriously injured or killed when your vehicle.
Page 22 General information 3. Open the fuel tank filler pipe by slowly turning the cap 4. To fill with fuel correctly depends mainly on correct han- counterclockwise. dling of the fuel filler nozzle. Do not tilt the nozzle. Insert the nozzle in the tank port as far as it goes. CAUTION Your vehicle can only be operated using unleaded gasoline.
Page 23 Always tighten the fuel tank filler pipe cap until you hear clicking sounds. The indicator will go off after driving several times. If the indicator does not go off, contact your authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible.
Page 24 Only Mitsubishi Motors approved accessories should be always possible for an authorized Mitsubishi Motors dealer to fitted to your vehicle. check whether the attachment or installation of non-Mitsubishi Improper installation of electrical parts could cause fire.
Page 25: Mitsubishi Motors Genuine Parts
Also available from be fitted, or any modifications carried out which involve the your Mitsubishi Motors dealer are a wide variety of accessories electrical or fuel systems, should be carried out in accordance to personalize your new vehicle.
Page 26 General information California Perchlorate Materials Require- ments N00300100017 Certain components of this vehicle, such as airbag modules, seat belt pretensioners, and button cell batteries, may contain perchlorate materials. Special handling may apply. For additional information, see www.dtsc.ca.gov/hazardouswaste/perchlorate.
Page 28: Seat And Restraint Systems
Seat and restraint systems Seats ........2- Seats and restraint systems.
Page 29 Seat and restraint systems Seats N00408400437 1 - Front seats 2 - Rear seat To adjust the seat forward or backward → P.2-5 Arm rest → P.2-11 To adjust the seatback → P.2-6 To adjust the seat height (Driver’s side only) → P.2-8 To adjust the lumbar support (Driver’s side, Power seat only) →...
Page 30: Seats And Restraint Systems
Seat and restraint systems Seats and restraint systems Always check the following before you drive: That everyone in your vehicle is properly wearing their N00401600052 seat belt. Your vehicle has seat belts and other features that help protect That infants and small children are properly secured in you and your passengers in an accident.
Page 31: Front Seats
Seat and restraint systems Front seats WARNING N00401800360 Do not attempt to adjust the seat while driving. This Position the driver’s seat as far back as possible while main- can cause loss of vehicle control and result in an taining a position that still enables you to fully apply the ped- accident.
Page 32 Seat and restraint systems To adjust the seat forward or backward CAUTION N00401900299 Make sure that the seat is adjusted by an adult. If it Manual seat is adjusted by a child, an unexpected accident might Pull the seat adjusting lever up and slide the seat forward or occur.
Page 33 Seat and restraint systems Power seat To adjust the seatback Push the switch to adjust the seat forward or backward to the N00402000330 desired position. Release the switch, and the seat will lock at Manual seat that position. To adjust the seatback, lean forward slightly, gently pull the seatback lock lever up, then lean backward to a comfortable position and release the lever.
Page 34 Seat and restraint systems Power seat WARNING Adjust the seatback angle by operating the switch as indicated To reduce the risk of serious injury or death in the by the arrows. event of an accident or sudden stop, all seatbacks should be kept in the upright position while the vehi- cle is in motion.
Page 35 Seat and restraint systems To adjust the seat height (Driver’s side only) Power seat Front and/or rear parts of the seat cushion height can be N00402100227 adjusted. Manual seat Turn the dial to raise or lower the whole seat cushion. NOTE To prevent the battery from running down, operate the power seat with the engine running.
Page 36 Seat and restraint systems Rear part of the seat cushion Whole seat cushion Operate the switch to raise or lower the rear part of the seat Operate the center of the switch to raise or lower the whole seat cushion. cushion.
Page 37 Seat and restraint systems To adjust the lumbar support (Driver’s side, Heated seats (if so equipped) Power seat only) N00435600206 The heated seats can be operated when the ignition key is in the N00402200156 “ON” position. A lumbar support is included in the seatback of the driver’s seat.
Page 38: Rear Seat
Seat and restraint systems Rear seat CAUTION N00402500087 Switch off the seat heaters when not in use. Operate Arm rest the heaters at high for quick heating. After the seat has become warm, set the heater to low to keep it N00403000210 Tilt the arm rest down for use as shown.
Page 39: Head Restraints
Seat and restraint systems Trunk-through lid Head restraints N00409000023 N00404300555 Open the lid to gain access to the luggage compartment from Padded head restraints for the seats can reduce the risk of a the cabin. This feature is useful for storing and removing small whiplash injury if your vehicle is hit from the rear.
Page 40 Seat and restraint systems Adjustment of the head restraint height WARNING To reduce the risk of injury in an accident, adjust the head In order to minimize the risk of a neck injury due to restraint height so that the center of the restraint is at your eye a rear impact, the seatback must be adjusted to the level when seated.
Page 41 Seat and restraint systems To remove CAUTION Press the lock knob (A) in the direction shown by the arrow. Check that the lock knob (A) is extended out as Then pull the head restraint up and out of the seatback. shown in the illustration.
Page 42: Seat Belts
Seat and restraint systems Seat belts CAUTION N00406000282 Always use the correct head restraint provided for Seat belts are installed in your vehicle to help reduce the risk of the seat and do not install the head restraint in the injury to the driver and passenger in the event of an accident.
Page 43 Mitsubishi erly, remains seated all the way back and upright in Motors dealer to determine whether replacement is their seat, and moves the seat as far back as possible.
Page 44 Seat and restraint systems Seat belt instructions 1. Occupants should always sit back in their seats with their backs against the upright seatback. To reduce the risk of N00406200330 All seats are equipped with a seat belt which uses one com- serious injury or death during deployment of the air bag, bined lap-and-shoulder belt with an emergency locking retrac- adjust the driver’s seat as far back as possible while main-...
Page 45 Seat and restraint systems 2. Grasp the latch plate and slide it up the webbing so that it WARNING easily pulls across your body. To reduce the risk of serious injury or death in the event of an accident or sudden stop, all seatbacks should be kept in the upright position while the vehi- cle is in motion.
Page 46 Seat and restraint systems 3. Pull the seat belt out slowly while holding the latch plate. 4. The lap part of the belt must always be worn low and snug Push the latch plate into the buckle until you hear a across the hips.
Page 47 Seat and restraint systems Driver’s seat belt reminder/warning light NOTE With the exception of the seat belt for the driver, the seat N00418400153 A tone and warning light are used to remind the driver to fasten belts in all other seating positions are equipped with an the seat belt.
Page 48 Seat and restraint systems Front passenger seat belt warning light WARNING N00418300035 The front passenger seat belt warning light is located above the In order to reduce the risk of serious injury or death in an accident, always wear your own seat belt. Do central vents in the instrument panel.
Page 49 Seat and restraint systems Adjustable seat belt shoulder anchor (front seats) WARNING N00406300083 To move the anchor down, press the lock knob (A) and slide Always adjust the shoulder belt anchor so that the the anchor down to the desired position. shoulder belt is positioned across the center of your shoulder without touching your neck.
Page 50 Seat and restraint systems Seat belt guide (rear seat) Installation 1. Place the seat belt guide over the seat belt webbing and N00419300029 The seat belt guide for the rear seat outside positions will pro- insert the two edges (A) of the seat belt webbing into the vide added seat belt comfort for children who have outgrown slots (B) in the seat belt guide.
Page 51 Seat and restraint systems 2. Make sure the elastic cord (C) of the seat belt guide passes 3. Fasten the seat belt and make sure it fits snugly across behind the seat belt webbing. your shoulder. Refer to “Seat belt instructions” on page 2- CAUTION Make sure the part of the seat belt webbing you inserted into the seat belt guide is not twisted.
Page 52: Seat Belt Use During Pregnancy
Seat and restraint systems Seat belt extender Seat belt use during pregnancy N00406700104 N00406800088 When your seat belt, even fully extended, is not long enough, a Seat belts work for everyone, including pregnant women. Like seat belt extender must be obtained. The extender may be used all occupants, pregnant women are more likely to be seriously for either of the front seats.
Page 53 Seat and restraint systems Seat belt pre-tensioner and force limiter The seat belt pre-tensioner system includes the following com- ponents: systems N00417700175 The driver’s and front passenger’s seats each have a seat belt equipped with a pre-tensioner system. Pre-tensioner system The driver and front passenger seat belts are equipped with a seat belt pre-tensioner system.
Page 54 The seat belt pre-tensioner system is designed to work only once. After the seat belt pre-tensioners have been activated, they will not work again. They must promptly be replaced and the entire seat belt pre-tensioner system inspected by an authorized Mitsubishi Motors dealer. 2-27...
Page 55: Child Restraints
Seat and restraint systems Child restraints Children who weigh more than 40 pounds (18 kg) or who are more than 40 inches (100 cm) tall, regardless of age, N00407100668 should use a suitable child seat or a booster seat (including When transporting infants or small children in your vehicle, an a booster cushion) in the rear seat until the vehicle’s appropriate child restraint system must always be used.
Page 56 Seat and restraint systems WARNING WARNING Never hold an infant or child in your arms or on Your vehicle is also equipped with a front passenger your lap when riding in this vehicle, even when you air bag. are wearing your seat belt. Never place any part of Never put REAR-FACING CHILD RESTRAINTS the seat belt you are wearing around an infant or or INFANT RESTRAINTS in the front passenger...
Page 57 Seat and restraint systems WARNING WARNING FRONT-FACING CHILD RESTRAINTS should It is important to use an approved rear-facing infant always be used in the rear seat whenever possible. If restraint until the infant is one year old (unless the one must be used in the front passenger seat, move infant outgrows the seat sooner).
Page 58 Seat and restraint systems Installing a child restraint system using the NOTE Before purchasing a child restraint system, try installing it LATCH (Lower Anchors and Tethers for chil- in the rear seat to make sure there is a good fit. Because of dren) system the location of the seat belt buckles and the shape of the N00418800072...
Page 59 Seat and restraint systems Tether anchor locations Examples of child restraint systems compatible with the LATCH system N00418900161 Your vehicle has 3 attachment points on the rear shelf, located N00419000156 behind the top of your rear seat. These are for securing a child restraint system tether strap to each of the 3 rear seating posi- tions in your vehicle.
Page 60 Seat and restraint systems Using the LATCH system NOTE In order to secure a child restraint systems compatible N00419100115 1. Open the gap a little between the seat cushion (A) and the with the LATCH system, use the lower anchor points in seatback (B) with your hand to locate the lower anchors the outboard positions of the rear seat.
Page 61 Seat and restraint systems Installing a child restraint system using the seat 3. Open the cover for the tether anchor by pulling it back with your hand as illustrated below (3). belt (with emergency/automatic locking mecha- 4. Latch the tether strap hook (D) of the child restraint sys- nism) tem to the anchor (E) as illustrated below (4) and tighten N00407300325...
Page 62 Seat and restraint systems Installation: 3. To activate the ALR child restraint installation function, slowly pull the shoulder part of the belt all the way out of 1. Place the child restraint system in the rear seating posi- the retractor until it stops. Then let the belt feed back into tion.
Page 63 Seat and restraint systems 5. After confirming that the belt is locked, grab the shoulder 6. Open the cover from the tether anchor installation point part of the belt near the buckle and pull up to remove any by pulling it back with your hand as illustrated below (6). slack from the lap part of the belt allowing the slack to 7.
Page 64 Seat and restraint systems 9. To remove a child restraint system from the vehicle and WARNING deactivate the ALR mode, remove the child from the Never allow children to play in the trunk of your restraint. Unlatch the buckle. Then remove the belt from vehicle.
Page 65: Maintenance And Inspection Of Seat Belts
Mitsubishi Motors dealer. Failure to The SRS air bags are NOT a substitute for use of the seat belts. have an authorized Mitsubishi Motors dealer per- For maximum protection in all types of accidents, seat belts form the work could reduce the effectiveness of the...
Page 66 Seat and restraint systems WARNING WARNING IT IS VERY IMPORTANT TO BE PROPERLY IT IS VERY IMPORTANT TO ALWAYS WEAR SEATED. YOUR SEAT BELT PROPERLY EVEN WITH AN • A driver or front passenger sitting too close to the AIR BAG. steering wheel or instrument panel during air bag •...
Page 67 Seat and restraint systems WARNING WARNING Air bags inflate very quickly and with great force. Infants and small children should never ride unre- Do not sit on the edge of the seat or lean your head strained, or lean against the instrument panel. They or chest close to the steering wheel or the instrument should never ride held in your arms or on your lap.
Page 68 Seat and restraint systems WARNING WARNING NEVER REAR-FACING CHILD FRONT-FACING CHILD RESTRAINTS should be RESTRAINTS or INFANT RESTRAINTS seat in used in the rear seat whenever possible. If they must the front passenger seat. This places the infant too be used in the front passenger seat, move the seat to close to the passenger air bag.
Page 69 Seat and restraint systems How the Supplemental Restraint System works N00407800173 The SRS includes the following components: 9- Side air bag modules 10- Curtain air bag modules 11- Side impact sensors 1- Driver’s air bag The air bag control unit monitors the readiness of the electronic 2- SRS warning light parts of the system whenever the ignition switch is in the “ON”...
Page 70 Seat and restraint systems When the impact sensors detect a sufficient front or side impact Event Data Recording to deploy the air bag(s), the appropriate air bag(s) will be N00418600054 Your vehicle is equipped with an “EDR” - Event Data deployed.
Page 71 If any of the following conditions occur, you should back against the seatback. immediately have your vehicle inspected by an Refer to “Front seat” on page 2-4. authorized Mitsubishi Motors dealer as soon as pos- • Do not recline the seatback more than necessary sible: when driving.
Page 72 To ensure that the passenger’s seat weight sensors If the vehicle is involved in a severe impact, have the can correctly sense the weight being applied to the sensors inspected by an authorized Mitsubishi seat, observe the following instructions. Failure to Motors dealer as soon as possible.
Page 73 If any of the following conditions occur, you should tral vents in the instrument panel. immediately have the air bag system in your vehicle inspected by an authorized Mitsubishi Motors dealer as soon as possible: • The passenger’s air bag off indicator comes on when an adult is sitting on the front passenger seat.
Page 74 Mitsubishi Motors When the ignition key is in the “ON” or “START” position, the dealer: SRS warning light should come on for several seconds and •...
Page 75 Seat and restraint systems Driver’s and passenger’s front air bag system N00407900204 The driver’s air bag is located under the padded cover in the middle of the steering wheel. The front passenger’s air bag is contained in the instrument panel above the glove compart- ment.
Page 76 Seat and restraint systems Deployment of front air bags N00408000143 The front air bags ARE DESIGNED TO DEPLOY when … Head-on collision with a solid wall at Moderate to severe frontal impact within speeds of approx. 15 mph (25 km/h) or the shaded area between the arrows higher The front air bags are designed to deploy when the vehicle suf-...
Page 77 Seat and restraint systems The front air bags MAY NOT DEPLOY when … Collision with a utility pole, tree or other narrow object In certain types of frontal collisions, the front air bags may not deploy, even if the deformation of the body seems to be large, because the vehicle’s body structure is designed to absorb the impact and deform in order to help protect the occupants.
Page 78 Seat and restraint systems The front air bags ARE NOT DESIGNED TO Rear end collision to your vehicle DEPLOY when … The front air bags are not designed to deploy in situations where they cannot provide protection to the occupants. Some typical situations are shown in the illustrations.
Page 79 Seat and restraint systems The front air bags MAY DEPLOY when … Collision with an elevated median/island or curb The front air bags may deploy if the underside of the vehicle suffers a moderate to severe impact (undercarriage impact). Some typical these situations are shown in the illustrations. Because the front air bags may deploy in certain types of unex- pected impacts, as shown in the illustrations, and these unex- pected impacts can move you out of position, it is important to...
Page 80 The air bag system is designed to work only once. After the air bags deploy, they will not work again. They must promptly be replaced and the entire air bag system must be inspected by an authorized Mitsubishi Motors dealer. 2-53...
Page 81 Seat and restraint systems Side air bag system A label is attached to the seatbacks in vehicles with side air bags. N00408100388 The side air bags (A) are contained in the driver and front pas- senger seatbacks. The side air bag is designed to inflate only on the side of the vehicle that is impacted, even with no passenger in the front seat.
Page 82 Seat and restraint systems Curtain air bag system WARNING N00419200158 The curtain air bags are contained in the front and rear pillars The side air bags and curtain air bags can cause and roof side rail. The curtain air bag is designed to inflate only serious injury or death to anyone too close to the air bag when it deploys.
Page 83 Seat and restraint systems WARNING WARNING In order to reduce the risk of injury from a deploy- Do not attach a microphone (A) or any other object ing side air bag, do not allow any rear seat passen- around the part where the curtain air bag (B) gers to hold onto the back of either front seat.
Page 84 If the curtain air bag was acti- done only by an authorized Mitsubishi Motors vated, any such item could be propelled away with dealer. Improper work methods can cause acciden-...
Page 85 Seat and restraint systems Deployment of side air bag and curtain air bag The side air bag and curtain air bag MAY NOT DEPLOY when … N00408200031 In certain types of side collisions, the side air bag and curtain The side air bag and curtain air bag ARE DESIGNED air bag may not deploy, even if the deformation of the body TO DEPLOY when …...
Page 86 Seat and restraint systems Side impact in an area away from the passenger compartment Oblique side impact Vehicle rolls onto its side or roof Motorcycle or other similar small vehicle collision with the side of vehicle Collision with a utility pole, tree or other narrow object 2-59...
Page 87 SRS performance and may lead to injury. If your vehicle has received any damage, you should Rear end collision have the SRS inspected by an authorized Mitsubishi Motors dealer to make sure it is in proper working order. Do not modify your front seats, center pillar or cen- ter console.
Page 88 1-888-576-4878 or write to: If you decide to junk or scrap your vehicle, we urge you to first take it to an authorized Mitsubishi Motors dealer so Mitsubishi Motor Sales of Canada, Inc. that the SRS can be made safe for disposal.
Page 89: Warning Labels
Seat and restraint systems Warning labels N00408600224 Occupant restraint warning labels for the SRS are located in the vehicle as shown in the illustration. *: Located in the passenger’s side as well. 2-62...
Page 90: Features And Controls
Features and controls Break-in recommendations ....3- Instrument cluster ......3- 72 Keys .
Page 91 Features and controls Break-in recommendations Keys N00508700226 N00508800546 Advanced automobile manufacturing techniques permit you to Two keys are provided. operate your new vehicle without requiring a long break-in The keys fit all locks. Keep one in a safe place as a spare key. period of low-speed driving.
Page 92 The purpose of the system is to a key from your authorized Mitsubishi Motors dealer if immobilize the vehicle if an invalid start is attempted. A valid the original keys are lost.
Page 93 In cases like the above, move the offending object(s) away from the key and turn the key back to the “ACC” or “LOCK” position. Then try to start the engine again. If the engine does not start, contact an authorized Mitsubishi Motors dealer.
Page 94 Registering the ID code can be done by your authorized cially available remote starting systems may result in Mitsubishi Motors dealer. Or it can be done by yourself (except vehicle starting problems and a loss of security protection. for vehicles sold in Canada).
Page 95 “LOCK” position to the moment when the blank immobilizer key (specially cut for your vehicle at your Mitsubishi Motors dealer) is turned to the “ON” position • more than 30 seconds elapse after the immobilizer indi-...
Page 96: Keyless Entry System
Features and controls General information Keyless entry system Your electronic immobilizer operates on a radio frequency sub- N00509000848 Press the remote control transmitter buttons to lock or unlock ject to Federal Communications Commission (FCC) Rules the doors and to open the trunk lid. (For vehicles sold in U.S.A.) and Industry Canada Rules (For It can also help you signal for attention by setting off the panic vehicles sold in Canada).
Page 97 2. Release the LOCK and UNLOCK buttons within 10 sec- onds of pressing the UNLOCK button in step 1. NOTE On a vehicle equipped with a Mitsubishi Multi-Communi- NOTE cation System, the functions can be adjusted on the On a vehicle equipped with a Mitsubishi Multi-Communi- screen.
Page 98 10 seconds of pressing the LOCK button in automatically occur. step 1. On a vehicle equipped with a Mitsubishi Multi-Communi- cation System, the functions can be adjusted on the NOTE screen. For details, refer to a separate operation manual.
Page 99 Be sure to perform the procedure with the Mitsubishi the manufacturer for compliance could void the mark facing you. If the Mitsubishi mark is not facing you user’s authority to operate the equipment. when you open the remote control transmitter case, the buttons may come out.
Page 100 7. Check the keyless entry system to see that it works. NOTE You may purchase a replacement battery at an electric appliance store. Your authorized Mitsubishi Motors dealer can replace the battery for you if you prefer. 3-11...
Page 101: Door Locks
Features and controls Door locks CAUTION N00509200390 When the remote control transmitter case is opened, WARNING be careful to keep water, dust, etc. out. Also, do not touch the internal components. Make sure all doors are tightly closed and locked while driving.
Page 102 Features and controls To lock or unlock the door with the key (driver’s To lock or unlock the door from the inside door only) Move the lock knob to the lock position to lock the door. All doors should be kept locked while driving. Turn the key toward the front of the vehicle to lock the door.
Page 103: Power Door Locks
Features and controls To lock the door without using the key Power door locks 1. Move the inside lock knob to the locked position. N00509300447 2. Be sure the keys are not inside the vehicle. Close the door. NOTE Repeated continuous operation between lock and unlock could activate the power door locking system’s built-in protection circuit and prevent the system from operating.
Page 104 Features and controls “Child safety locks” for rear door For vehicles sold in Canada N00509400275 Except for vehicles sold in Canada 1- To lock 2- To release Child safety locks help prevent rear passengers, especially chil- dren, from opening the rear door using the inside door handle. A lock lever for the child safety lock is provided on each rear door.
Page 105: Trunk Lid
Features and controls Trunk lid WARNING N00509500120 Always keep the doors tightly closed and locked WARNING when driving. An unlocked door may be acciden- tally opened by a passenger, especially by a child It is dangerous to drive with the trunk lid open since who could fall out.
Page 106 Features and controls To open NOTE The trunk light comes on when the trunk lid is opened, N00545200020 and goes out when it is closed. Operation from outside the vehicle Use the remote control transmitter to open. Press the trunk but- To close ton.
Page 107: Inside Emergency Trunk Lid Release
Features and controls Inside emergency trunk lid release CAUTION N00509800123 Before starting the vehicle, be sure to confirm that The emergency trunk lid release is designed to provide a way the trunk lid is closed. If the trunk lid opens while to open the trunk lid from inside the trunk.
Page 108 Features and controls You and your family should familiarize yourselves with the To open the trunk from the inside, pull the handle in the direc- location and operation of the emergency trunk lid release han- tion of the arrow on the handle. Push up on the trunk lid to dle.
Page 109: Armed Stage
Features and controls Theft-alarm system NOTE (if so equipped) The system is also armed by locking your vehicle using N00510200042 the following procedures when you leave the vehicle. The theft-alarm system is designed to provide protection from • With either the driver’s door or passenger’s door open, unauthorized entry into the vehicle.
Page 110 Features and controls Type of alarm NOTE The system will be armed even if the engine hood is open, When the alarm is activated: but when the system is set, be sure that the engine hood is 1. The headlights blink on and off for 3 minutes. locked.
Page 111: Disarmed Stage
Features and controls Disarmed stage Testing the theft-alarm system N00510500074 N00510600046 The system will be disarmed when either of the following steps Use the following procedure to test the system: are taken: 1. Lower the driver’s window. 1. All doors are unlocked by the remote control transmitter. 2.
Page 112: Power Windows
Features and controls Power windows WARNING N00510800312 Before operating the power windows, make sure that nothing can be trapped (head, hands, fingers, etc.) in the window. Never leave the vehicle without removing the key. Never leave a child alone in the vehicle. 1- Open (down) 2- Close (up) NOTE...
Page 113: Main Switch
Features and controls Main switch Sub switch The main switch located on the driver’s door can be used to operate all the door windows. The windows will move while the switch is pressed and stop when the switch is released. 1- Close 2- Open A sub switch can be used for its own passenger door window,...
Page 114 Features and controls Lock switch What to do if you hear wind buffeting when driv- N00549000039 When this switch is in the lock mode, the passenger door N00551400014 switches cannot be used to open or close the door windows, Wind buffeting can be described as the perception of pressure and the main switch will open or close only the driver’s door on the ears or a booming or rumbling sound.
Page 115 Features and controls Sunroof To close (if so equipped) The sunroof closes while the switch (3) is pressed. N00511000597 The sunroof can be opened and closed with the ignition key in To tilt up the “ON” position. When the switch (2) is pressed, the rear edge of sunroof raises for ventilation.
Page 116 If nothing is trapped, have the Be careful that hands are not trapped when closing sunroof checked at an authorized Mitsubishi Motors the sunshade. dealer or a repair facility of your choice.
Page 117: Parking Brake
Features and controls Do not put any wax on the weatherstrip (black rubber) Parking brake around the sunroof opening. If it is waxed, the N00511400139 weatherstrip cannot maintain a weatherproof seal with the To park the vehicle, first bring it to a complete stop, fully sunroof.
Page 118: Steering Wheel Tilt Lock Lever
Features and controls To release Steering wheel tilt lock lever N00511500156 To adjust the steering wheel height, release the tilt lock lever while holding the steering wheel by hand, and raise or lower the steering wheel to the desired height. After adjustment, securely lock the lever by pulling it upward.
Page 119: Inside Rearview Mirror
Features and controls Inside rearview mirror WARNING N00511600199 After adjusting, make sure the lock lever is secured Adjust the inside rearview mirror only after making any seat in the locked (1) position. adjustments so as to have a clear view to the rear of the vehicle. Do not attempt to adjust the steering wheel while driving.
Page 120 Features and controls Adjust the inside mirror to maximize the view through the rear To reduce the glare window. Type 1 To adjust the vertical mirror position The day/night knob (A) at the bottom of the mirror can be used It is possible to move the mirror up and down to adjust its posi- to adjust the mirror to reduce the glare from the headlights of tion.
Page 121: Outside Rearview Mirrors
Features and controls Outside rearview mirrors Type 2 N00512200189 When the headlights of the vehicles behind you are very bright, Adjust the outside rearview mirrors only after making any seat the reflection factor of the rearview mirror is automatically adjustments so you have a clear view to the rear of the vehicle. changed to reduce the glare.
Page 122 Features and controls To adjust the mirror position Heated mirror (if so equipped) The outside rearview mirrors can be adjusted when the ignition N00549300133 When the rear window defogger switch is pressed, the outside key is in the “ON” or “ACC” position. rearview mirrors are defogged or defrosted.
Page 123: Ignition Switch
Features and controls Ignition switch START Engages the starter. After the engine starts, release the key and N00512400657 it will return automatically to the “ON” position. NOTE If your vehicle is equipped with ignition switch illumina- tion, the ignition switch will be illuminated: •...
Page 124 Features and controls To remove the key CAUTION Do not turn the key to the “START” position when the engine is running. It will damage the starter motor. Key reminder buzzer N00551000078 If you open the driver’s door while the ignition key is in the “LOCK”...
Page 125: Steering Wheel Lock
Features and controls Steering wheel lock NOTE If the front wheels are turned, the anti-theft lock may N00512500137 sometimes make it difficult to turn the key from “LOCK” to “ACC”. Firmly turn the steering wheel to the left or to the right as you turn the key.
Page 126 Features and controls Starting CAUTION N00512600691 Release the ignition key as soon as the engine starts. Tips for starting Otherwise, the starter motor will be damaged. Do not operate the starter motor continuously for longer than 15 seconds as this could run the battery down or Starting the engine damage the starter motor.
Page 127 Features and controls Startability of automatic transaxle vehicle with ambient Using the MIVEC engine ° ° temperature of -31 F (-35 C) or lower The MIVEC engine automatically switches its intake-valve When the ambient temperature is -31 °F (-35 °C) or lower, it control between a low-speed mode and a high-speed mode in may not be possible to start from a standstill even with the accordance with driving conditions for maximum engine per-...
Page 128: Automatic Transaxle
Features and controls Automatic transaxle NOTE During the break-in period or immediately after recon- N00513200098 necting the battery, your vehicle may not shift smoothly. Designed for the most efficient control and equipped with self- This does not indicate a problem in the transaxle. Shifting adapting capabilities, the electronically controlled transaxle will become smoother once the transaxle has been shifted used in your vehicle selects the most favorable gear for each...
Page 129 Features and controls The transaxle has 4 forward gears and 1 reverse gear. In the main gate, the selector lever has 4 positions, and is The individual gears are selected automatically, depending on equipped with a lock button (A) to prevent inadvertent selec- the position of the gear selector lever, the speed of the vehicle tion of the wrong gear.
Page 130 Features and controls WARNING Always depress the brake pedal when shifting the selector lever into a gear from the “N” (NEUTRAL) position. When beginning to drive, do not shift the selector lever from the “N” (NEUTRAL) position while depressing the accelerator pedal. This will cause the vehicle to “jump”...
Page 131 The automatic transaxle safety device may be oper- (REVERSE) or “N” (NEUTRAL) position, the indicator ating due to a malfunction. does not blink.) Have your vehicle inspected by an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. 3-42...
Page 132 Features and controls Selector lever positions “N” NEUTRAL At this position, the transaxle is disengaged. It is the same as N00514200268 the neutral position on a manual transaxle and should be used “P” PARK when the vehicle is not moving for an extended length of time This position locks the transaxle to prevent the vehicle from during driving, such as in a traffic jam.
Page 133 Features and controls Sports mode CAUTION N00514400387 Whether the vehicle is stationary or in motion, sports mode is Upward shifts do not take place automatically in selected by pushing the selector lever from the “D” position sports mode. The driver must make upward shifts in into the manual gate.
Page 134 Features and controls Move the selector lever gently between the manual and Operation of the automatic transaxle main gates and between positions in the manual gate. N00514500290 Excessive force could damage the selector lever. CAUTION When sports mode is selected, the “D” indicator goes out. Before selecting a gear with the engine running and Sports mode indicator the vehicle stationary, fully depress the brake pedal...
Page 135 Features and controls Passing acceleration CAUTION N00514900047 To gain extra acceleration in “D” (DRIVE) position (when Use the selector lever in the correct shift position in passing another vehicle) push the accelerator to the floor. The accordance with driving conditions. automatic transaxle will automatically downshift.
Page 136: Service Brake
Have Do not leave any objects near the brake pedal or let your vehicle checked at an authorized Mitsubishi Motors a floor mat slide under it; doing so could prevent the dealer or a repair facility of your choice as soon as possible.
Page 137 If you hear this sound, have the brake pads replaced at an Your brakes are designed to operate at full capacity, even if the authorized Mitsubishi Motors dealer or a repair facility of your power assist is lost. choice.
Page 138 Features and controls Anti-lock braking system CAUTION N00517900253 The anti-lock braking system cannot prevent acci- The anti-lock braking system helps prevent the wheels from dents. It is your responsibility to take safety precau- locking up when braking. This helps you keep control of your tions and to drive carefully.
Page 139 Only the ordinary braking system is function- ing. If this happens, take your vehicle to an authorized Mitsubishi Motors dealer or a repair facility of your choice and have the system checked as soon as possible. NOTE...
Page 140 Features and controls Active stability control (ASC) Front N00559100088 The active stability control (ASC) takes overall control of the anti-lock braking system, traction control function and skid control function to help maintain the vehicle’s control and trac- tion. Also refer to the following pages on the anti-lock braking system, traction control function and skid control function.
Page 141 Features and controls Traction control function NOTE A whining sound may be heard from the engine compart- N00559200063 On slippery surfaces, the traction control function prevents the ment in the following situations. The sound is associated drive wheels from spinning excessively, thus helping the vehi- with the ASC self-check operations.
Page 142 Features and controls Skid control function ASC OFF switch N00546800036 N00559400094 The skid control function is designed to help the driver main- The ASC is automatically activated when the ignition key is tain control of the vehicle on slippery roads or during rapid turned to the “ON”...
Page 143 “ON” position, have the vehicle ASC, using the ASC OFF switch. inspected by an authorized Mitsubishi Motors dealer or a repair If you continue to press the ASC OFF switch after the facility of your choice as soon as possible.
Page 144 If the indicators remain on even after your vehicle is driven a short distance after re- starting the engine, have the vehicle inspected by an authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. 3-55...
Page 145: Power Steering System
If this happens, take your vehicle to an autho- the ignition key in the “ACC” position. rized Mitsubishi Motors dealer or a repair facility of your Refer to “Towing” on page 6-21. choice.
Page 146: Cruise Control
Features and controls Cruise control CAUTION N00518300469 Cruise control is not recommended when driving Cruise control is an automatic speed control system. It lets you conditions will not allow you to stay at the same keep the same driving speed. Cruise control can be used at speed, such as in heavy traffic or on roads that are speeds of about 25 mph (40 km/h) or more.
Page 147: Cruise Control Indicator
Features and controls Cruise control indicator To activate N00550100173 N00518400196 This indicator will come on when the cruise control main 1. Momentarily push in the main switch (A) at the end of the switch is “ON”. cruise control lever. 3-58...
Page 148 Features and controls To increase the set speed 2. Pull the lever (B) down while driving at the desired speed. N00518500243 There are 2 ways to increase the set speed. Cruise control lever Pull the cruise control lever up and hold it while driving at the set speed, and your speed will then gradually increase.
Page 149 Features and controls Accelerator pedal To decrease the set speed Press the accelerator pedal to reach your desired speed. Pull the N00518600114 There are 2 ways to reduce the set speed. cruise control lever down for a moment, then release it. Cruise control lever Pull the cruise control lever down and hold it while driving at the set speed, and you will slow down (coast) gradually.
Page 150 Features and controls Brake pedal To accelerate for passing Press the brake pedal (which disengages the cruise control), N00518700098 Press the accelerator pedal as you would normally. When you then pull the cruise control lever down momentarily to set a release the pedal, the cruise control will return to your set new desired cruise speed.
Page 151 Features and controls To deactivate WARNING N00518800523 The cruise control can be turned off as follows: Although the cruise control can be turned off by Push the main switch (A) at the end of the lever. moving the selector lever to the “N” position, never (Main switch OFF) move the selector lever to the “N”...
Page 152: Tire Pressure Monitoring System
Features and controls To resume the set speed Tire pressure monitoring system N00518900120 N00530200341 If the speed memory has not been erased, resume the previ- The tire pressure monitoring system uses tire inflation pressure ously set speed by pulling the cruise control lever up while sensors (A) on the wheels to monitor the tire inflation pres- driving at a speed of 25 mph (40 km/h) or higher.
Page 153 When the spare tire is used, the tire pressure moni- Motors dealer. toring system will not work properly. See an authorized Mitsubishi Motors dealer as soon as possible to replace or repair the original tire. NOTE The tire pressure monitoring system is not a substitute for regularly checking tire inflation pressures.
Page 154 Have vehicle inspected by an authorized Mitsubishi the system inspected by an authorized Mitsubishi Motors dealer. Motors dealer. In such situations, a malfunctioning of the system...
Page 155 Features and controls Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure tell- tale.
Page 156 2. If the tire pressure monitoring system warning light Mitsubishi Motors dealer. If the tire repair is not done by remains illuminated after you have been driving for about an authorized Mitsubishi Motors dealer, it is not covered 20 minutes after you adjust the tire inflation pressure, one by your warranty.
Page 157 Have tire and wheel replacement performed by The tire inflation pressure sensors’ battery is exhausted. an authorized Mitsubishi Motors dealer to avoid the risk of Wheels other than Mitsubishi Motors genuine wheels are damaging the tire inflation pressure sensors. If the wheel being used.
Page 158 “ON” position, the rear-view (FCC) Rules (For vehicles sold in U.S.A.) and Industry Canada image will be displayed on the screen of the Mitsubishi Multi- Rules (For vehicles sold in Canada). This device complies with communication System in the center panel.
Page 159 Features and controls Location of rear-view camera Screen image The rear-view camera (A) is in the trunk lid. Reference guide marks, upper surface of the rear bumper (A) and a part of the trunk lid (C) are displayed on the screen. Five guide marks in red (B) indicates approximately 20 inches (50 cm) behind the rear bumper.
Page 160 It is possible to set the display language of the screen to English, Spanish or French. For details, please refer to the separated owner’s manual for “Mitsubishi Multi-Communication System”. Under certain circumstances, it may become difficult to see an image on the screen, even when the system is func- tioning correctly.
Page 161 Features and controls Instrument cluster N00519000287 1- Tachometer 2- Speedometer 3- Fuel gauge 4- Odometer/Trip odometer 5- Trip odometer reset button 6- Engine coolant temperature gauge 3-72...
Page 162 Features and controls Speedometer Odometer/Trip odometer N00519100015 N00519500338 The speedometer shows your vehicle’s speed. When the ignition switch is in the “ON” position, an “ODO” or “TRIP” indicator is displayed. Tachometer N00519200032 The tachometer shows engine revolutions per minute. This allows the driver to determine the most efficient gear range and engine speed combinations.
Page 163 Features and controls Every time the reset button (3) is pressed lightly (less than one To reset the trip meter second), the indicators are changed. To zero the counter, press and hold the reset button for more than one second. Only the currently displayed value will be reset.
Page 164 Features and controls Fuel gauge Fuel tank filler door mark The arrow (A) indicates that the fuel tank filler door is located N00519600052 This gauge shows the amount of fuel in the fuel tank when the on the left side of the vehicle (Refer to “Filling the fuel tank” ignition key is turned to the “ON”...
Page 165 Features and controls Engine coolant temperature gauge N00519700037 This gauge shows the engine coolant temperature. If the tem- perature is low when the ignition key is turned to the “ON” position, the indicator will remain at the “C” (cold) position until the engine begins to warm up.
Page 166: Indicator And Warning Light Package
Features and controls Indicator and warning light package N00519800780 14- Tire pressure monitoring system warning light → P.3-65 1- Engine malfunction indicator (“SERVICE ENGINE SOON” or “Check engine light”) → P.3-79 15- Supplemental Restraint System (SRS) warning light → P.2-47 2- Cruise control indicator →...
Page 167: Warning Lights
• The brake warning light remains illuminated dur- ing driving. • If any of the above situations occur, stop the vehi- cle in a safe location, avoiding any sudden brake application, and contact your nearest authorized Mitsubishi Motors dealer or a repair facility of your choice. 3-78...
Page 168 This will make it diffi- at an authorized Mitsubishi Motors dealer or a repair facility of cult to diagnose the cause of future problems.
Page 169 If this light comes on when the engine oil level is not low, have your vehicle checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice. This warning light does not show the amount of oil in the crankcase.
Page 170: Combination Headlights And Dimmer Switch
Features and controls Combination headlights and dimmer switch [When the engine is started and the parking brake is released] N00522500622 The daytime running lights come on. (if so equipped) Headlights Rotate the switch to operate the lights. OFF Headlights illuminate dimly Headlights illuminate dimly and Parking, tail, front and rear side-marker lights, license plate and instrument panel lights on...
Page 171 For details, refer to the separate owner’s manual. Mitsubishi Motors dealer or a repair facility of your When you want to keep the lights on: choice. If the light switch is turned to the “...
Page 172 Features and controls Dimmer (high/low beam change) 3. The light will automatically turn off after 3 minutes. N00549900126 NOTE To change the headlights from high beam to low beam and vice When the driver’s door is opened, a continuous high- versa, pull the turn signal lever to fully toward you (1).
Page 173: Headlight Flasher
Features and controls Headlight flasher Turn signal lever N00550000169 N00522600434 You can flash the high beams by pulling the lever gently When changing lanes, or to making a gradual turn, hold the toward you (2). The lights will go back to normal when you let lever in the “lane change”...
Page 174: Hazard Warning Flasher Switch
If the panel light does not come on when the lever is moved, check for a blown fuse or a burned out bulb in the panel. Have the vehicle inspected by an authorized Mitsubishi Motors dealer or a repair facility of your choice. For vehicles equipped with the Mitsubishi Multi-Commu-...
Page 175 Features and controls Fog light switch Do not use fog lamps except in conditions of fog, other- (if so equipped) wise excessive lamp glare may temporarily blind oncom- N00522800364 ing vehicle drivers. The fog lights illuminate only when the headlights are on low beam.
Page 176: Wiper And Washer Switch
Features and controls Instrument panel light dimmer control Wiper and washer switch N00522900176 N00523000549 The brightness of the instrument panel lights can be adjusted Windshield wipers by turning this control while the light switch is in the “ ” or The windshield wipers wipe when the wiper lever is moved as “...
Page 177 Features and controls Misting function NOTE For vehicles equipped with the Mitsubishi Multi-Commu- Move the lever in the direction of the arrow and release, and nication System, Mitsubishi Multi-Communication Sys- the wipers will operate once. tem can be used to enable and disable speed-sensitive Use this function when you are driving in mist or drizzle.
Page 178 Features and controls Windshield washer Precautions to observe when using wipers and washers N00504600025 To turn on the windshield washer, pull the lever toward you N00523500225 with the ignition key in either the “ON” or “ACC” position. The wipers will wipe automatically several times when the CAUTION washer fluid is sprayed.
Page 179: Electric Rear Window Defogger Switch
Electric rear window defogger switch proper size replacement blades. If you have questions, ask N00523700357 your authorized Mitsubishi Motors dealer. The electric rear window defogger can be used with the igni- tion key in the “ON” position. The indicator light (A) will come on when you press the elec- tric rear window defogger switch.
Page 180 Features and controls Horn switch CAUTION N00523800101 The rear window defogger is not designed to melt To honk the horn, press near the “ ” mark on the steering snow. Remove any snow manually before using the wheel. rear window defogger. Use the rear window defogger only after the engine has started and is running.
Page 181 Features and controls ® Hands-free Bluetooth cellular phone WARNING interface system with voice recognition (if so ® Although the Bluetooth HFP allows you to make equipped) hands-free calls, if you choose to use the cellular N00506400102 phone while driving, you must not allow that usage ®...
Page 182 Features and controls Overhead console control switch PHONE button Press this button when an incoming call is received to N00546700048 answer the telephone. When another call is received during a call, press this but- ton to put the first caller on hold and talk to the new caller. •...
Page 183 Features and controls Voice recognition function NOTE When you press the SPEECH button to enter voice recog- N00506600133 ® nition mode with a cellular phone paired to the system, The Bluetooth HFP is equipped with a voice recognition current information on the cellular phone, such as function.
Page 184 Features and controls Change the language using the “Language” command Speaker enrollment function 1. Press the SPEECH button. N00528900080 ® The Bluetooth HFP can use the speaker enrollment function 2. Say “Setup.” to create a voice model for one person per language. 3.
Page 185 Features and controls Speaker enrollment NOTE If you do not start the speaker enrollment process within 3 N00529000020 It takes a few minutes to complete the speaker enrolment pro- minutes of pressing the SPEECH button, the speaker cess. enrollment function will time out. To ensure the best results, run through the process while in the The voice guide will say “Speaker Enrollment has timed driver’s seat, in an environment that is as quiet as possible...
Page 186 Features and controls 8. When all enrollment commands have been read out, the 4. When enrollment is “enabled,” the voice model is on; voice guide will say “Speaker Enrollment is complete.” when enrollment is “disabled,” the voice model is off. Say The system will then end the speaker enrollment process the command that fits your needs.
Page 187: Help Function
Features and controls Help function 1. Press the SPEECH button. 2. Say “Setup.” N00506700033 ® The Bluetooth HFP is equipped with a Help function. 3. Say “Confirmation prompts.” If you say “Help” when the system is waiting for a voice com- 4.
Page 188 3. Say “Passcode.” the voice input mode and then check with an authorized 4. The voice guide will say “Passcode is disabled. Would Mitsubishi Motors dealer. you like to enable it?” Answer “Yes.” Disabling the passcode Answer “No” to cancel the setting of the passcode and return to the main menu.
Page 189 Features and controls Pairing a cellular phone ® Use the following procedure to pair a Bluetooth compatible ® N00507100164 cellular phone to the Bluetooth HFP. ® ® To use the Bluetooth HFP, you need to pair a Bluetooth 1. Stop your vehicle in a safe area, put the selector lever in ®...
Page 190 Features and controls ® 7. After the voice guide says “Please say a 4-digit pairing 9. When the system finds a Bluetooth compatible cellular code,” say a 4-digit code. The 4-digit code will be regis- phone, the voice guide will say “Please say the name of tered as a pairing code for the phone.
Page 191 5. After the voice guide says “<phone tag> selected,” the If you are having difficulty pairing the phone, assistance system will reconnect to the cellular phone. Wait a can be obtained by calling Mitsubishi hands free con- moment for the process to complete. sumer support line 1-888-702-4100.
Page 192 Features and controls Having the system tell you a list of the registered Deleting a phone cellular phones N00507400053 ® Use the following procedure to delete a paired Bluetooth N00507300052 You can use the following procedure to hear a list of the cellu- ®...
Page 193 Features and controls 7. When the phone deletion process is completed, the voice NOTE In the case of English, the system will recognize both guide will say “Deleted.” The system will then beep and “zero” and “oh (Letter “o”) for the number “0.” Refer to the voice recognition mode will be exited.
Page 194 Features and controls Redialing 5. After the voice guide says “Calling <voice tag> at <loca- ® N00507800015 tion>,” the Bluetooth HFP will make the call. You can redial the last number called, based on the history of When the confirmation function is on, the system will dialed calls in the paired cellular phone.
Page 195 Features and controls Switching between hands-free mode and private Phonebook function mode N00508300020 ® The Bluetooth HFP has its own phonebook separate from the N00508100031 ® phonebook on the cellular phone. The Bluetooth HFP can switch between Hands-free mode This phonebook is used when making calls with the voice rec- (Hands-free calls) and private mode (calls using cellular ognition function.
Page 196 Features and controls New entry 3. Say the telephone number to register it. N00508400050 NOTE You can register a new entry in the phonebook by saying “New In the case of English, the system will recognize both entry” on the phonebook main menu. You can register up to a “zero”...
Page 197 Features and controls Edit 3. After the voice guide says “Number Please,” say the tele- phone number to register it. N00508500035 You can edit information in the phonebook by saying “Edit” on If a telephone number has been registered for the selected the phonebook main menu.
Page 198 Features and controls Having the system tell you a list of the phonebook Deleting a registered number entries N00511700057 You can delete a telephone number in the phonebook by saying N00508600052 “Delete” on the phonebook main menu. You can hear a list of the names registered in the phonebook by saying “List names”...
Page 199 Features and controls General information 4. When the deletion of the telephone number is completed, the voice guide will say “<voice tag> <location> deleted” N00511900046 MODEL: MMC FCC ID: CB2MBLUEC07 IC: 279B- and then the system will return to the main menu. MBLUEC07 NOTE ®...
Page 200 Features and controls Voice Command Tree N00512000086 3-111...
Page 201 Features and controls Voice Command Tree - Phonebook N00512100045 3-112...
Page 202 Features and controls Voice Command Tree - Setup N00512800039 3-113...
Page 203 Features and controls Commands and Alternatives Lan- Alternative Command Primary Command N00513300073 guage Commands Lan- Alternative English Pair Command Primary Command guage Commands PAIR Spanish Emparejar English Setup French Jumeler SETUP Spanish Configuración English Delete A Phone Delete French Configurer Eliminar Un Telé- DELETE A Spanish...
Page 204 Features and controls Lan- Alternative Lan- Alternative Command Primary Command Command Primary Command guage Commands guage Commands English Add Location English Edit Agregar {Una} EDIT Spanish Editar Spanish Ubicación French Modifier LOCATION Ajouter {Un} English Call This Number Call French Emplacement CALL THIS Llamar A Este...
Page 205 Features and controls Lan- Alternative Lan- Alternative Command Primary Command Command Primary Command guage Commands guage Commands English Home English HOME Spanish Casa En Su Casa Spanish Todos French Maison À La Maison French Tous English Work English Cancel WORK Spanish Trabajo En Su Trabajo...
Page 206 Features and controls Lan- Alternative Lan- Alternative Command Primary Command Command Primary Command guage Commands guage Commands English English Spanish Spanish Seis French French English Zero Oh (letter “O” ) English Seven ZERO Spanish Cero SEVEN Spanish Siete French Zéro O (lettre «o») French Sept...
Page 207 Features and controls Lan- Alternative Lan- Alternative Command Primary Command Command Primary Command guage Commands guage Commands English English Phonebook List English Spoken Names Spanish Español PHONE- Language BOOK Agenda - Listar French Français Spanish LIST Nombres Phonebook New NAMES English Répertoire Liste Entry...
Page 208 Features and controls Lan- Alternative Lan- Alternative Command Primary Command Command Primary Command guage Commands guage Commands Setup Pairing English Passcode English Setup Pairing Options PASSCODE Spanish Contraseña Configuración French SETUP Spanish Opciones De Empa- PAIRING English Setup Passcode rejamiento OPTIONS SETUP Configuración Con-...
Page 209 Features and controls Lan- Alternative Phrase # English Spanish French Command Primary Command guage Commands 7 Continue Continuar Continuer English Join Calls 8 Help Ayude Aide JOIN Spanish Unir Llamadas CALLS French Intégrer L’appel English English ENGLISH Spanish Inglés French Anglais l’anglais English...
Page 210: Sun Visors
Features and controls Sun visors Slide plate To block out additional side glare, swing the sun visor side- N00524600063 Fold the sun visor downward (1) to reduce front glare while ways and pull out the slide plate (A). driving. To reduce side glare, turn the visor to the side (2). 3-121...
Page 211: Vanity Mirror
Features and controls Vanity mirror Power outlet N00524700211 N00525000442 The vanity mirror is located on the back of the sun visor. To use a “plug-in” type accessory, open the cover located in If your vehicle is equipped with mirror lights, opening the lid front of the floor console, then insert the plug in the socket.
Page 212 Features and controls Digital clock NOTE (if so equipped) If the battery cables are disconnected or the battery N00525100209 becomes discharged, the clock will have to be reset. When the ignition switch is in the “ACC” or “ON” position, the time is displayed. How each button works: Set the time by pressing the various buttons as described below.
Page 213 Features and controls HomeLink® Wireless Control System HomeLink® is powered by your vehicle’s battery. No sep- (if so arate batteries are required. If the vehicle’s battery is dis- equipped) charged or is disconnected, HomeLink® will retain all N00554300027 programming. HomeLink® Wireless Control System is a registered trademark Once HomeLink®...
Page 214 Features and controls 2. Press and hold the 2 outer HomeLink® buttons (A) (to Programming HomeLink® clear the memory) until the indicator light (B) blinks To program HomeLink® to operate a garage door, gate, or slowly (after 20 seconds). Release both buttons. entry door opener, home or office lighting, you need to be at 3.
Page 215 Features and controls Programming HomeLink® for Canadian cus- 6. If the indicator light on HomeLink® blinks rapidly for 2 seconds and then turns solid, HomeLink® has picked up a tomers “rolling code” garage door opener signal. Now continue Prior to 1992, D.O.C regulations required hand-held transmit- with the next steps to train HomeLink®...
Page 216 Features and controls If you continue to have programming difficulties, please con- General information tact an authorized Mitsubishi Motors dealer or a repair facility Your HomeLink® system operates on a radio frequency sub- of your choice. ject to Federal Communications Commission (FCC) Rules (For vehicles sold in U.S.A.) and Industry Canada Rules (For...
Page 217: Interior Lights
Features and controls Interior lights Reading lights N00525700175 N00525300445 Push the reading light switch (A) to turn on the light. This light produces a spot beam for convenient use as a map light. Dome light Reading lights → P.3-129 → P.3-128 Push the reading light switch again to turn the light off.
Page 218 The time until the light goes off can be adjusted. See your authorized Mitsubishi Motors dealer for details. For vehicles equipped with the Mitsubishi Multi-Commu- nication System, adjustments can be made using screen operations. For details, refer to the separate owner’s man- ual.
Page 219 If any of the interior lights are left on with the ignition switch authorized Mitsubishi Motors dealer for details. in the “LOCK” position, the lights go off automatically after For vehicles equipped with the Mitsubishi Multi-Commu- about 30 minutes. nication System, adjustments can be made using screen The lights come on again if the ignition switch is turned to the operations.
Page 220: Glove Compartment
Features and controls Accessory boxes Glove compartment N00526400443 N00526500242 Convenient storage space is located throughout the vehicle. To open, pull the lever (A). NOTE 1- Glove compartment When the light switch is set in either the “ ” or “ ”...
Page 221 Features and controls Floor console box/Tissue holder/Pen hold- Tissue holder/Pen holder The tissue holder (A) and pen holders (B) are located on the back of the arm rest. N00526600168 Floor console box The floor console box is located under the arm rest. To open the console box, lift the lever (A) and raise the arm rest (B).
Page 222: Cup Holder
Features and controls Cup holder For the rear seat N00537000032 N00527300263 This cup holder is located in the rear seat arm rest (A). For the front seat Pull the rear arm rest down to use the cup holder. The cup holder is located in the middle of the floor console. The cup holder is designed for holding cups or drink-cans securely in its holes.
Page 223: Luggage Hooks
Features and controls Luggage hooks Coat hook N00528500220 N00553600036 There are four hooks on the side of the trunk for use in securing There is a hook on the rear driver’s side assist grip for use in luggage. hanging clothes. NOTE WARNING Do not hang heavy luggage {more than about 6.6 pound...
Page 224: Driving Safety
Driving safety Fuel economy......4- Driving, alcohol and drugs....4- Vehicle preparation before driving.
Page 225: Fuel Economy
Driving safety Fuel economy Driving, alcohol and drugs N00628800080 N00628900010 Fuel economy is dependent on many factors. Your personal Drunk driving is one of the most frequent causes of accidents. driving habits can have a significant effect on your fuel use. Your driving ability can be seriously impaired even with blood Several recommendations for achieving the greatest fuel econ- alcohol levels far below the legal minimum.
Page 226: Vehicle Preparation Before Driving
Always use retaining clip on the driver’s floorboard to secure the Mitsubishi genuine floor mat. When used, this clip will Seat belts and seats help prevent the floor mat from moving forward and possibly Before starting the vehicle, make certain that you and all interfering with the operation of the pedals.
Page 227 Tire replacement should, therefore, be performed only by an authorized Mitsubishi Motors dealer. Lights Have someone watch while you turn all the exterior lights on Defrosters and off.
Page 228: Safe Driving Techniques
Driving safety Safe driving techniques Driving during cold weather N00629200052 N00629400272 Even this vehicle’s safety equipment, and your safest driving, Check the battery, including terminals and cables. During cannot guarantee that you can avoid an accident or injury. extremely cold weather, the battery will not be as strong. However, if you give extra attention to the following areas, you Also, the battery power level may drop because more can better protect yourself and your passengers:...
Page 229 All the parts of the brake system are critical to safety. Have the freeze and water. The recommended blend is about 50 % vehicle serviced by an authorized Mitsubishi Motors dealer or water and 50 % anti-freeze. Use a higher concentration a repair facility of your choice at regular intervals according to (not over 60 %) when the outside temperature is -31 °F...
Page 230 Driving safety Parking Where you park N00629600229 WARNING Parking on a hill When parking on a hill, set the parking brake, and turn the Do not park your vehicle in areas where combustible front wheels toward the curb on a downhill, or away from the materials such as dry grass or leaves can come in curb on an uphill.
Page 231: Loading Information
Driving safety Loading information Curb weight: the weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, N00629900381 and coolant. It is very important to know how much weight your vehicle can Accessory weight: the combined weight (in excess of carry.
Page 232: Tire And Loading Information Placard
Driving safety Tire and loading information placard This placard shows the maximum number of occupants permit- ted to ride in your vehicle as well as “the combined weight of N00630100211 The tire and loading information placard is located on the occupants and cargo”...
Page 233 Driving safety Type 2 Steps for Determining Correct Load Limit N00630200065 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 234 Driving safety NOTE The following table shows examples on how to calculate total cargo/load capacity of your vehicle with varying seating config- urations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load capacity of your vehicle.
Page 235: Cargo Loads
Driving safety Cargo loads WARNING N00629700419 To reduce the risk of serious injury or death, the Cargo load precautions combined weights of the driver, passengers and To determine the cargo load capacity for your vehicle, subtract cargo and must never exceed the vehicle capacity the weight of all vehicle occupants from the vehicle capacity weight.
Page 236: Trailer Towing
Driving safety Trailer towing N00629800061 WARNING Do not use this vehicle for trailer towing. It may not be possible to maintain control or adequate braking. 4-13...
Page 238: Comfort Controls
Comfort controls Vents........5- Manual air conditioning (if so equipped)..5- Automatic air conditioning (if so equipped) .
Page 239 Comfort controls Vents Air flow and direction adjustments N00730200053 N00729900193 Center/Side vents Adjust the direction of the air flow by moving the knob (A). Center vents Side vents 1- Center vents 2- Side vents NOTE NOTE On rare occasions, air from the vents of an air-conditioned Do not place beverages on top of the instrument panel.
Page 240 Comfort controls Changing the mode selection Foot/Face position Air flows to the upper part of the passenger compartment, and N00736400507 To change the position and amount of air flowing from the flows to the leg area. vents, turn the mode selection dial. (Refer to “Mode selection dial”...
Page 241 Comfort controls Foot position Foot/Defroster position Air flows mainly to the leg area. Air flows to the leg area, the windshield and the door windows. NOTE With the mode selection dial between the “ ” and “ ” positions, air flows mainly to the leg area. With the mode selection dial between the “...
Page 242 Comfort controls Defroster position Manual air conditioning (if so equipped) Air flows mainly to the windshield and the door windows. N00730300139 The air conditioning can only be used while the engine is run- ning. Control panel N00730500232 NOTE When the mode selection dial is set to the “ ”...
Page 243 Comfort controls Blower speed selection dial Temperature control dial N00736500159 N00736600118 When the ignition key is in the ON position, select the blower Turn the temperature control dial clockwise to make the air speed by turning the blower speed selection dial. The blower warmer.
Page 244 Comfort controls Mode selection dial Air selection switch N00736700076 N00736800338 To change the position and amount of air flowing from the Normally, use the outside position to keep the windshield and vents, turn the mode selection dial. (Refer to “Changing the side windows clear and to quickly remove fog or frost from the mode selection”...
Page 245 Comfort controls Air conditioning switch NOTE N00731000407 When the “ ” or “ ” position is selected, you cannot Push the switch, and the air conditioning compressor will turn turn the air conditioning off or use the recirculation posi- on. The air conditioning indicator light (A) will come on. tion.
Page 246 If it does blink, Turn the temperature control dial clockwise or counterclock- have it checked at an authorized Mitsubishi Motors dealer wise to the desired temperature. Select the desired blower or a repair facility of your choice.
Page 247 Comfort controls Cooling NOTE If the outside air is dusty or contaminated in some way, set N00731200294 the air selection switch (A) to the recirculation position. For ordinary cooling Let in some outside air from time to time for good ventila- tion.
Page 248 Comfort controls For quick cooling Combination of unheated air and heated air N00731300237 Select the mode selection dial to the positions shown in the illustration and set the air selection switch (A) to the outside position. The air flow will be directed to the leg area and the upper part of the passenger compartment.
Page 249 Comfort controls Defrosting or defogging the windshield and door win- For ordinary defrosting Use this setting to keep the windshield and door windows clear dows of mist, and to keep the leg area heated (when driving in rain or N00731400498 snow).
Page 250 Comfort controls For quick defrosting Automatic air conditioning (if so equipped) N00731500095 The air conditioning can only be used while the engine is run- ning. Control panel N00711800513 1. Set the mode selection dial to the “ ” position. 2. Set the blower to the maximum speed. 3.
Page 251 Comfort controls Blower speed selection dial NOTE There is an interior air temperature sensor (A) in the illus- N00736900140 When the ignition key is in the ON position, select the blower trated position. speed by turning the blower speed selection dial. The blower Never place anything over the sensor, since doing so will speed will gradually increase as the dial is turned to the right.
Page 252 Comfort controls Temperature control dial Mode selection dial N00737000294 N00737100194 Turn the temperature control dial clockwise to make the air To change the position and amount of air flowing from the warmer. Turn it counterclockwise to make the air cooler. vents, turn the mode selection dial.
Page 253 Comfort controls Air selection switch CAUTION N00737200326 Normally, use the outside position to keep the windshield and Using recirculated air for a long time may cause the side windows clear and to quickly remove fog or frost from the windows to fog up. windshield.
Page 254 If the air conditioning indicator light does not blink, there is no problem. If it does blink, have it checked at an authorized Mitsubishi Motors dealer or a repair facility of your choice. Sometimes, for example after using a high-pressure car wash, the condenser can get wet, and the air conditioning indicator light (A) blinks temporarily.
Page 255 Comfort controls Operating the air conditioning system (automatic NOTE Set the temperature at about 75 under normal conditions. mode) When the temperature is set to the highest or the lowest N00731700329 setting under the AUTO operation, the air selection and the air conditioning will be automatically changed as fol- lows.
Page 256 Comfort controls Operating the air conditioning system (manual For ordinary defrosting Use this setting to keep the windshield and door windows clear mode) of mist, and to keep the leg area heated (when driving in rain or N00731800027 snow). Blower speed and vent mode may be controlled manually by setting the blower speed selection dial and the mode selection dial to the desired positions.
Page 257 Comfort controls For quick defrosting To stop the air conditioning N00732500210 To turn the air conditioning off, set the blower speed selection dial to the “OFF” position. All operations will stop except the air selection. 1. Set the mode selection dial to the “ ”...
Page 258 This includes the quick might be a refrigerant leak. defrosting mode. Operating the air condition system weekly Have the system inspected by your authorized Mitsubishi maintains lubrication of the compressor internal parts and Motors dealer or a repair facility of your choice.
Page 259: Audio System
Comfort controls Audio system N00734301020 Your vehicle is equipped with the following audio system: (1) AM/FM electronically tuned radio with CD player (Type 1) → P.5-24 (2) AM/FM electronically tuned radio with CD autochanger (Type 2) → P.5-37 (3) AM/FM/Satellite electronically tuned radio with CD autochanger (Type 3) → P.5-37 The audio system can only be used when the ignition switch is in the “ON”...
Page 260 9-2. rized Mitsubishi Motors dealer or repair facility of your “SIRIUS”, the SIRIUS dog logo and channel names and logos choice. Never try to repair it yourself. Avoid using the are trademarks of SIRUS Satellite Radio, Inc.
Page 261 Comfort controls AM/FM electronically tuned radio with CD player-Type 1 (if so equipped) N00734300993 Volume and tone control panel N00711900657 1- PWR (On-Off) switch 2- VOL (Volume control) knob 3- AUDIO switch 4- Display 5-24...
Page 262 Comfort controls To adjust the volume N00712000033 VOL (Volume control) Turn the VOL knob (2) clockwise to increase the volume; counterclockwise to decrease the volume. The status will be displayed in the display (4). NOTE The volume control mode will shut off automatically if either the radio or CD is selected, or if no adjustment is made within about 2 seconds.
Page 263 Comfort controls To adjust the tone N00712100340 1. Press the AUDIO switch (3) repeatedly to select the tone or balance control to change. The order is: BASS → TRE → FADE → BAL → Audio adjust mode off. The status will be displayed in the display (4). 5-26...
Page 264 Comfort controls 2. Turn the AUDIO switch (3) either clockwise or counter- clockwise to change the tone/balance setting. Adjusting operation Mode Clockwise Counterclockwise BASS Increase Decrease Increase Decrease More sound from the More sound from the FADE rear speakers front speakers More sound from the More sound from the right speakers...
Page 265 Comfort controls Radio control panel and display N00734900843 1- PWR (On-Off) switch 2- Memory select buttons 3- RADIO (AM/FM selection) button 4- SEEK (Up-seek) button 5- SEEK (Down-seek) button 6- SCAN button 7- TUNE/FOLDER switch 8- SCAN indicator 9- AM/FM (AM/FM1/FM2) indicator 10- Preset memory number display 11- ST (Stereo) indicator 12- Frequency display...
Page 266 Comfort controls To listen to the radio To store a frequency in the memory, follow these steps: 1. Press the SEEK button (4 or 5), or turn the N00735000825 1. Press the PWR switch (1) to turn the audio system on and TUNE/FOLDER switch (7) to tune to the frequency you off.
Page 267 Comfort controls CD control panel and display N00735300668 1- PWR (On-Off) switch 11- RPT (Repeat-mode) indicator 2- CD eject button 12- RDM (Random-mode) indicator 3- Disc loading slot 13- SCAN indicator 4- RADIO (AM/FM selection) button 14- CD indicator 5- CD (CD mode changeover) button 15- TRACK indicator 6- TRACK (Track up) button 16- Track play time display...
Page 268 Comfort controls To listen to a CD To listen an MP3 CD This player allows you to play MP3 (MPEG Audio Layer-3) N00735501016 1. Press the CD button (5) and the CD mode will be selected, files recorded on CD-ROMs, CD-Rs (recordable CDs), and starting a playback.
Page 269 Comfort controls Folder selection order/MP3 file playback order (Example) NOTE While listening to a disc on which CD-DA (CD-Digital Audio) and MP3 files have both been recorded, you can switch between reading of the CD-DA and reading of the Root folder (root directory) MP3 files, and the external audio input mode by pressing the CD button for 2 seconds or longer (until you hear a beep).
Page 270 Comfort controls To fast forward/reverse the disc To select a desired folder (MP3 CDs only) To fast forward or reverse, use the TRACK button (6 or 7). You can select your desired folder by turning the TUNE/FOLDER switch (10). Fast forward You can fast forward by holding down the side of the TRACK button (6) for more than about 1 second.
Page 271 Comfort controls To select a desired track To repeat the same track or change the order of tracks You can select by using the TRACK button (6 or 7). for playback Press the RPT/RDM button (8) to select RPT → RDM → Track up RPT/RDM mode off.
Page 272 Comfort controls Random playback for all folders on a disc (MP3 CDs only) Select the RDM mode, and the RDM indicator (12) will come on. Tracks from all the folders on the disc will be played in a random sequence. NOTE With a disc that contains both CD-DA and MP3 files, the random mode causes only files of the same format (CD-...
Page 273 Comfort controls To find the start of each track on a disc for playback Press the SCAN button (9). “SCAN” will appear on the display and the player will play back the first 10 seconds of each track on the selected disc. The track number will blink while the scan mode is selected.
Page 274 Comfort controls AM/FM electronically tuned radio with CD autochanger-Type 2 (if so equipped) AM/FM/Satellite electronically tuned radio with CD autochanger-Type 3 (if so equipped) N00734300951 Volume and tone control panel-Type 2, Type 3 N00711900699 1- PWR (On-Off) switch 2- VOL (Volume control) knob 3- Memory select buttons 4- AUDIO switch 5- Display...
Page 275 Comfort controls To adjust the volume To adjust the tone N00712000381 N00712100643 1. Press the AUDIO switch (4) repeatedly to select your VOL (Volume control) desired sound customization setting to change. The order Turn the VOL knob (2) clockwise to increase the volume; is: SUB GAIN →...
Page 276 Comfort controls MID (Midrange tone control) 2. Turn the AUDIO switch (4) either clockwise or counter- clockwise to adjust the sound customization features. To select the desired midrange level. TRE (Treble tone control) Adjusting operation To select the desired treble level. Mode Clockwise Counterclockwise...
Page 277 Comfort controls TYPE (Music type select) To store your current sound settings into memory, follow these steps: To select the desired equalizer type. 1. Go to the “SOUND PRESET” setting (preset button lights will be flashing). Music type Description 2. Push one of the memory select buttons (3) for more than 2 NONE Sounds good for all types of music.
Page 278 Comfort controls Speed Compensated Volume function N00752200226 Speed Compensated Volume function is a feature that automat- ically adjusts the VOL, BASS, MID, and TREBLE settings in accordance with the vehicle speed. It is possible to turn this function ON-OFF using the following methods: 1.
Page 279 Comfort controls Radio control panel and display-Type 2 N00734900827 1- PWR (On-Off) switch 2- Memory select buttons 3- RADIO (AM/FM selection) button 4- SEEK (Up-seek) button 5- SEEK (Down-seek) button 6- SCAN button 7- TUNE/FOLDER switch 8- SCAN indicator 9- AM/FM (AM/FM1/FM2) indicator 10- Preset memory number display 11- ST (Stereo) indicator 12- Frequency display...
Page 280 Comfort controls To listen to the radio To store a frequency in the memory, follow these steps: 1. Press the SEEK button (4 or 5), or turn the N00735000870 1. Press the PWR switch (1) or RADIO button (3) to turn on TUNE/FOLDER switch (7) to tune to the frequency you the radio.
Page 281 Comfort controls Radio control panel and display-Type 3 N00734900830 1- PWR (On-Off) switch 2- Memory select buttons 3- RADIO (AM/FM/Satellite selection) button 4- SEEK (Up-seek) button 5- SEEK (Down-seek) button 6- SCAN button 7- TUNE/FOLDER switch 8- SCAN indicator 9- AM/FM/SAT (AM/FM1/FM2/SAT1/SAT2/SAT3/SAT4) indicator 10- Preset memory number display 11- ST (Stereo) indicator...
Page 282 Comfort controls To listen to the radio To store a frequency in the memory, follow these steps: 1. Press the SEEK button (4 or 5), or turn the N00735000883 1. Press the PWR switch (1) or RADIO button (3) to turn on TUNE/FOLDER switch (7) to tune to the frequency you the radio.
Page 283 Comfort controls SIRIUS Satellite Radio control panel and display-Type 3 N00700200243 1. PWR (On-Off) switch 2. RADIO (AM/FM/Satellite selection) button 3. SEEK (Down-seek) button 4. SEEK (Up-seek) button 5. SCAN button 6. TUNE/FOLDER (Category selection) switch/AUDIO switch 7. Memory select buttons 8.
Page 284 Comfort controls To listen to SIRIUS Satellite Radio Channel selection N00700300026 N00700500028 Push the SEEK button (3 or 4) to select a channel. 1. If the audio system is OFF, turn it ON by pushing the PWR switch (1). The audio system will start working in NOTE the previously used mode.
Page 285 Comfort controls NOTE 1. If you select “CH 0”, the first 4 digits of the 12-digit SIR- Once you have stored channels in memory, you can IUS ID will be indicated 2 seconds later. instantly call up a desired channel by just pushing the cor- 2.
Page 286 Comfort controls To skip or lock a desired channel using the MENU SKIP setting (SKIP setting mode) mode N00701200048 It is possible to set a channel to be skipped during channel N00701100047 selection. It is also possible to cancel a skip setting. It is possible to make a setting to skip or lock a desired channel By turning the AUDIO switch (6), you can select “SKIP”...
Page 287 Comfort controls To skip a desired channel To cancel skip settings N00701400040 N00701500041 It is possible to set a channel to not be received during channel It is possible to cancel channel skip settings. selection. 1. Push the AUDIO switch (6) for at least about 2 seconds to 1.
Page 288 Comfort controls To unlock locked channels 5. Use the memory select buttons (7) to enter the code (1111 to 6666). N00701700056 You can unlock one or all locked channels. Unlocking one or more channels requires entry of the code. NOTE The code is set to “1111”...
Page 289 Comfort controls To change the lock cancellation code To reset the lock cancellation code N00701800057 N00701900045 It is possible to change the code for lock cancellation to any In case you forget the code, it is possible to reset the code to the desired number.
Page 290 Comfort controls CD control panel and display-Type 2, Type 3 N00735300714 16- RDM (Random-mode) indicator 1- LOAD-EJECT button 17- Track play time display 2- Disc loading slot 18- SCAN indicator 3- DISC select buttons 4- PWR (On-Off) switch 5- RADIO (AM/FM selection) button 6- CD (CD mode changeover) button 7- TRACK (Track up) button 8- TRACK (Track down) button...
Page 291 Comfort controls To listen to a CD To set a disc The indicator light (A) shows the condition of each disc slot. N00735501029 1. Press the CD button (6) and the CD mode will be selected, starting a playback. NOTE As many as 6 CDs can be inserted into the CD autochanger.
Page 292 Comfort controls To listen an MP3 CD NOTE When the first disc has played to the end, the second disc This autochanger allows you to play MP3 (MPEG Audio will start to play automatically. When the second, third, Layer-3) files recorded on CD-ROMs, CD-Rs (recordable fourth, fifth, and sixth discs have each played to the end, CDs), and CD-RWs (rewritable CDs) in ISO9660 Level the sequence will begin again from the first disc.
Page 293 Comfort controls Folder selection order/MP3 file playback order (Example) NOTE While listening to a disc on which CD-DA (CD-Digital Audio) and MP3 files have both been recorded, you can Root folder (root directory) switch between reading of the CD-DA and reading of the MP3 files, and the external audio input mode by pressing the CD button for 2 seconds or longer (until you hear a beep).
Page 294 Comfort controls To fast forward/reverse the disc To select a desired folder (MP3 CDs only) To fast forward or reverse, use the TRACK button (7 or 8). You can select your desired folder by turning the TUNE/FOLDER switch (11). Fast forward You can fast forward by holding down the side of the TRACK button (7) for more than about 1 second.
Page 295 Comfort controls To select a desired track To repeat the same track or change the order of tracks You can select by using the TRACK button (7 or 8). for playback Press the RPT/RDM button (9) to select RPT → RDM → Track up RPT/RDM mode off.
Page 296 Comfort controls Random playback for all folders on a disc (MP3 CDs only) Select the RDM mode, and the RDM indicator (16) will come on. Tracks from all the folders on the currently selected disc will be played in a random sequence. NOTE The Random playback mode will be canceled by pressing the SCAN button (10) or the LOAD/EJECT button (1).
Page 297: To Use The External Audio Input Function
Comfort controls To find the start of each track on a disc for playback To use the external audio input function Press the SCAN button (10). “SCAN” will appear on the dis- N00702200159 play and the autochanger will play back the first 10 seconds of each track on the selected disc.
Page 298 Comfort controls To activate the external audio input mode NOTE The connected audio equipment cannot be operated with the vehicle’s audio system. Depending on the connected audio equipment, it may pro- duce noise from the speakers. Use the connected audio equipment’s own power source, such as its battery.
Page 299 Comfort controls Steering wheel remote control switch NOTE (if so Do not push two or more of the steering wheel remote equipped) control switches at the same time. N00714800312 The remote control switches are located on the rear surface of To turn on the power the steering wheel.
Page 300 Comfort controls Automatic radio tuning To fast-forward/fast-reverse the disc (Type 1 and Type 2 audio system only) Seek up button — 1/Seek down button — 5 To fast-forward or fast-reverse the disc, press the fast-forward After pressing these buttons, reception of the selected station button (1) or the fast-reverse button (5).
Page 301: Error Codes
Eject disc and reload. If disc will not eject, Loading or eject error. bring your vehicle to your authorized E 03 Mechanism error Pick-up is out of position. Mitsubishi Motors dealer or a repair facility of your choice for repair. 5-64...
Page 302 Bring your vehicle to your authorized Communication or E Com device and audio equipment. Power supply Mitsubishi Motors dealer or a repair facility power supply error error of external device. of your choice for repair. Foreign material is inside of radio or ampli-...
Page 303 Repair Take the vehicle to your authorized The antenna may be faulty, not securely con- Antenna error Mitsubishi Motors dealer or a repair facility nected, or open-circuited. of your choice. Cannot pick up sig- Move to a place where the signal is easy to LINKING The signal is too weak to be received.
Page 304 Take the vehicle to your authorized Mechanical fault or There is a mechanical fault or a bad connec- SAT E Mitsubishi Motors dealer or a repair facility bad connection tion. of your choice. This channel is not broadcasting at the...
Page 305: Handling Of Compact Discs
Comfort controls Handling of compact discs N00734100223 Use only the type of compact discs that have the mark shown in the illustration below. (Playback of CD-R or CD-RW discs may cause problems.) The use of special shaped, damaged compact discs (like cracked discs) or low-quality compact discs (like warped discs or burrs on the discs) such as those shown will dam- age the CD player.
Page 306 Comfort controls In the following circumstances, moisture can form on To clean a disc, use a soft, clean, dry cloth. Wipe directly compact discs and inside the audio system, preventing from the center hole toward the outer edge. Do not wipe in normal operation.
Page 307 Do not remove the cover and attempt to repair the CD player by yourself. There are no user serviceable parts inside. In case of malfunction, contact an authorized Mitsubishi Motors dealer or a repair facility of your choice. 5-70...
Page 308 Comfort controls Antenna Satellite radio antenna (if so equipped) The antenna is located as shown in the illustration. N00734200325 Glass antenna The antenna is embedded in the inner side of the rear window glass. NOTE When the rear window glass is cleaned, wipe the glass with a soft cloth by moving the cloth along the antenna so as not to damage it.
Page 309 Comfort controls General information about your radio Weak reception (fading) Because of the limited range of FM signals and the way FM N00733900266 Your vehicle’s radio receives both AM and FM stations. waves transmit, you may experience weak or fading FM recep- The quality of your reception is affected by distance, obstacles, tion.
Page 310 Comfort controls Cross modulation Causes of disturbances If one listens to a weak station and is in the vicinity of another FM reception is affected by the electrical systems of vehicles in strong station, both stations might be received simultaneously. the vicinity, especially those without an electronic noise sup- pression device.
Page 312: For Emergencies
For emergencies If the vehicle breaks down ....6- Jump-starting the engine ....6- Engine overheating .
Page 313: If The Vehicle Breaks Down
For emergencies If the vehicle breaks down Jump-starting the engine N00836300174 N00836400696 If your vehicle breaks down on the road, move to the shoulder If the engine cannot be started because the battery is weak or and turn on the hazard warning flashers. If there is no shoulder, dead, you can start it with the battery from another vehicle or the shoulder is not safe, drive in the right lane slowly, with using jumper cables.
Page 314 For emergencies 3. You could be injured if the vehicles move. Set the parking 5. Connect one end of one jumper cable to the positive (+) brake firmly on each vehicle. Put an automatic transaxle terminal of the discharged battery (A), and the other end in “P”...
Page 315 For emergencies 6. Connect one end of the other jumper cable to the negative 8. After the engine is started, disconnect the cables in the (-) terminal of the booster battery (B), and the other end to reverse order from the way you connected them. the engine block of the vehicle with the low battery (A) at the point farthest from the battery.
Page 316: Engine Overheating
3. Check that the cooling fan is running. If the fan is not turning, stop the engine immediately and contact an authorized Mitsubishi Motors dealer or a repair facility of your choice for assistance. WARNING To avoid personal injury, keep hands, hair, jewelry and clothes away from the cooling fan.
Page 317 For emergencies 5. If you do not see steam or spray coming from under the 6. When you do not see any more steam or spray, open the hood, leave the engine on until the temperature indicator hood. Look for obvious leaks, such as a split radiator on the instrument panel moves below the red zone.
Page 318: Tools And Jack
Before removing the tools and the jack, lift up the luggage returns to the normal zone. floor board. 11. Have your vehicle checked by your authorized Mitsubishi Motors dealer or a repair facility of your choice. 1- Tools 2- Jack...
Page 319 For emergencies Tools Jack N00832600153 N00832700226 To store Retract the jack, then return it to its original position. To retract To expand 1- Bar 2- Wheel nut wrench...
Page 320: How To Change A Tire
For emergencies How to change a tire 5. To prevent the vehicle from rolling when it is raised on the jack, place chocks or blocks (A) at the tire that is diago- N00836900806 nally opposite from the tire (B) you are changing. Before changing a tire, first stop your vehicle in a safe, flat location.
Page 321 Spare tire information properly. Have the tire replaced or repaired at an N00849600243 authorized Mitsubishi Motors dealer or a repair Compact spare tire facility of your choice as soon as possible. If your vehicle has aluminum type wheels, you can The compact spare tire is designed to save space in the trunk.
Page 322 For emergencies To remove the spare tire CAUTION N00849700202 Do not put the compact spare tire on a different 1. Lift up the luggage floor board. wheel, and do not put standard tires, snow tires, 2. Remove the jack storage box. wheel covers or trim rings on the compact spare 3.
Page 323 For emergencies To change a tire NOTE Put the spare tire under the vehicle body near the jack. N00849800317 This makes it safer if the jack slips out of position. 1. On vehicles with wheel covers, first remove the covers (refer to “Wheel covers”...
Page 324 For emergencies 2. Place the jack under one of the jacking points (A) shown 3. Rotate the jack by hand until the flange portion (B) fits in in the illustration. Use the jacking point closest to the tire the groove (C) at the top of the jack. you wish to change.
Page 325 For emergencies 4. Insert the bar (D) into the wheel nut wrench (E). Then put WARNING the end of the bar into the shaft’s jack end, as shown in the No one should be in your vehicle when using the illustration.
Page 326 For emergencies 6. Clean out any mud, etc. on the hub surface (F), hub bolts WARNING (G) or in the installation holes (H) in the wheel, and then Mount the spare wheel with the valve stem (I) facing mount the spare tire. outboard.
Page 327 For emergencies [Vehicle with aluminum wheels] 7. [Vehicle with steel wheels] • Normal wheels Install the wheel nuts (tapered nuts) with their tapered Temporarily tighten the wheel nuts (flange nuts) until ends facing inward, then tighten by hand until the wheel is their flange section comes in contact with the wheel and no longer loose.
Page 328 For emergencies • Compact spare wheel 8. Lower the vehicle slowly by rotating the wheel nut Install the wheel nuts with their tapered ends facing wrench counterclockwise until the tire touches the inward, then tighten by hand until the wheel is no longer ground.
Page 329 For emergencies 9. Tighten the nuts in the order shown in the illustration until 11. Check the tire inflation pressure. The recommended tire each nut has been tightened to the torque listed here. pressure for your vehicle is listed on the tire and loading information placard attached to the driver’s door sill as 88 to 108 N•m (65 to 80 ft-lb) shown in the illustration.
Page 330 When the compact spare tire is used, the tire pressure monitoring system will not work properly. See an authorized Mitsubishi Motors dealer as soon as possible to replace or repair the original tire. After changing the tire and driving the vehicle about 620 miles (1,000 km), retighten the wheel nuts to make sure that they have not come loose.
Page 331 For emergencies NOTE NOTE The wheel cover is made of plastic. Be careful when pry- The full wheel cover is marked with a symbol (C) on the ing it off. reverse side that shows the air valve location. Before installing the wheel cover to the wheel, make sure CAUTION that the opening with the symbol mark (C) is correctly aligned with the air valve.
Page 332 For emergencies Towing N00837000774 If your vehicle needs to be towed If towing is necessary, we recommend you to have it done by a commercial tow truck service. When towing is required, transport the vehicle using a tow truck. Incorrect towing equipment could damage your vehicle. CAUTION Do not attempt to be towed by another vehicle with a rope.
Page 333 For emergencies Towing the vehicle by a tow truck Towing with rear wheels off the ground (Type B) Place the selector lever in the “N” (NEUTRAL) position. Turn the ignition key to the “ACC” position and secure the CAUTION steering wheel in a straight-ahead position with a rope or tie- This vehicle must not be towed by a tow truck using down strap.
Page 334: Operation Under Adverse Driving Conditions
For emergencies Operation under adverse driving conditions On wet roads N00837200688 CAUTION If your vehicle becomes stuck in sand, mud or snow Avoid flooded roads. Water is often deeper than it looks, and you could be seriously hurt by driving If your vehicle becomes stuck in snow, sand, or mud, it can into flood water.
Page 335 For emergencies On snowy or icy roads On a bumpy or rutted road When driving on a road covered with snow or ice, use Drive as slow as possible when driving on bumpy or rut- snow tires. Tire chains cannot be used on your vehicle. ted roads or over potholes etc.
Page 336: Vehicle Care And Maintenance
Vehicle care and maintenance Service precautions ......7- Replacement of light bulbs ....7- 44 Catalytic converter .
Page 337: Service Precautions
If you discover a malfunction or other problem, have it cor- wrong way can injure you. Ask an authorized rected by an authorized Mitsubishi Motors dealer or a repair Mitsubishi Motors dealer or a repair facility of your facility of your choice.
Page 338: Catalytic Converter
Have an inspection made by an result in damage to the converter and vehicle. authorized Mitsubishi Motors dealer or a repair facility of your choice as soon as possible. In unusual situations involving major engine problems, a...
Page 339: Engine Hood
Vehicle care and maintenance Engine hood Release the safety lever and lift the engine hood. N00937500480 To open Use the engine hood release lever (located under the instrument panel near the driver’s door) to unlock the engine hood. Pull the lever toward you to release the engine hood latch. NOTE To prevent damage to the engine hood and wipers, make sure the wipers are at resting position when you open the...
Page 340 Vehicle care and maintenance Support the engine hood with the hood prop. Insert the hood To close prop securely in the opening under the hood marked with an Unlatch the prop from the engine hood and put it back in its arrow.
Page 341: View Of The Engine Compartment
Vehicle care and maintenance View of the engine compartment Engine oil and oil filter N00937600612 N00937700815 To check and refill engine oil It is normal for an engine to use oil. You may need to add oil between the recommended oil change intervals. Before starting the engine, check the engine oil level.
Page 342 Don’t let used oil touch your skin. Wash thor- Engine oil identification mark oughly after working with it. Mitsubishi Motors recommends using only engine oils with the Keep used oil out of the reach of children. ILSAC certification symbol on the front of the container.
Page 343 Vehicle care and maintenance If you cannot find oils with the ILSAC certification symbol, Recommended engine oil viscosity use an API classification SM or higher oil with the following Use engine oil with the proper thickness for the outdoor tem- label.
Page 344: Engine Coolant
256 psi “F” (FULL) and “L” (LOW) marks. The radiator normally (1.8 MPa). A Genuine Mitsubishi oil filter is the best replace- remains completely full so there is no need to remove the radi- ment filter.
Page 345 Take your vehicle to an Radiator cap authorized Mitsubishi Motors dealer or a repair facility of your The radiator cap must be tight sealed to prevent losing coolant choice for testing.
Page 346: Air Cleaner Filter
N00937900370 rized Mitsubishi Motors dealer or a repair facility of your The air cleaner filter will get dirty and dusty from use and not choice to have the thermostat checked, and replaced if filter properly.
Page 347: Automatic Transaxle Fluid
The automatic transaxle should be maintained and serviced by idling, select each gear momentarily, ending with the an authorized Mitsubishi Motors dealer or a repair facility of selector lever in the “P” (PARK) position. your choice to obtain the best performance and longest life. It 2.
Page 348: Washer Fluid
Special additives Check the washer fluid level at regular intervals and add Mitsubishi Motors Corporation does not recommend the addi- washer fluid to reservoir if necessary. tion of any fluid additives to the transaxle. During cold weather When freezing weather is anticipated, flush out the water in the reservoir by operating the pump.
Page 349: Brake Fluid
If the brake fluid level falls markedly in a short length of time, it indicates leaks from the brake system. If this occurs, have the vehicle checked by an authorized Mitsubishi Motors dealer or a repair facility of your choice. 7-14...
Page 350: Power Steering Fluid
“MAX” and “MIN” level markings on the If battery performance is suspect, have the battery and charging fluid reservoir and refill the fluid, if necessary. system tested by an authorized Mitsubishi Motors dealer or a repair facility of your choice. Fluid type...
Page 351 Vehicle care and maintenance Checking battery electrolyte level 2. The inside of the battery is divided into several compart- ments. Use the following procedure to check the battery electrolyte Check the electrolyte level (A) in each cell. level. The electrolyte level must be within the range (B) shown 1.
Page 352 It is recommended that you have your battery and charging sys- tem checked by an authorized Mitsubishi Motors dealer or a repair facility of your choice before the start of cold weather. If necessary, have it charged. This will guarantee more reliable starting, and longer battery life.
Page 353 If the electrolyte level is very low, have the battery Never short-circuit the battery. This could cause it checked at an authorized Mitsubishi Motors dealer to overheat and be damaged. or a repair facility of your choice. Keep sparks, cigarettes, and flames away from the Battery terminals and related accessories contain battery because the battery could explode.
Page 354 Vehicle care and maintenance Tires Intended outboard sidewall: • The sidewall that contains a whitewall, bears white let- N00939200537 tering or bears manufacturer, brand, and/or model name WARNING molding that is higher or deeper than the same molding on the other sidewall of the tire, Driving with tires that are worn, damaged or improperly inflated is dangerous.
Page 355: Tire Markings
Vehicle care and maintenance Cord: the strands forming the plies in the tire. Tire Markings Rim: a metal support for a tire or a tire and tube assembly upon which the tire beads are seated. Rim diameter: nominal diameter of the bead seat. Groove: the space between two adjacent tread ribs.
Page 356 Vehicle care and maintenance Size Designation Service Description EXAMPLE:P215/65R15 EXAMPLE: 95H Passenger car tire size based on U.S.A. design Load index standards A numerical code associated with the maxi- mum load a tire can carry. Section width in millimeters (MM.) Speed symbol Aspect ratio in percent (%) A symbol indicating the range of speeds at...
Page 357 Vehicle care and maintenance Maximum Pressure Treadwear, Traction and Temperature Grades Maximum Pressure indicates the maximum permissible Treadwear cold tire inflation pressure for this tire. The treadwear grade is a comparative rating based on the wear Tire Identification Number (TIN) rate of the tire when tested under controlled conditions on a specified government test course.
Page 358 Vehicle care and maintenance Tire inflation pressures The recommended inflation pressures should be used for the tires listed below. N00939300798 Proper tire inflation pressure is essential for the safe and satis- factory operation of your vehicle. The wrong tire pressure will Item Tire size Front...
Page 359 Consult an authorized Mitsubishi Motors dealer or a repair facility of your choice before using wheels that you have. Only Mitsubishi Motors genuine wheels should be used, because your vehicle is equipped with a tire pressure monitoring system.
Page 360 Abnormal wear is usually caused by a wrong tire pressure, wheels that are not aligned properly, wheels that are out-of-balance, or severe braking. Check with an authorized Mitsubishi Motors dealer or a repair facility of your choice to find out the reason for uneven tread wear.
Page 361 Vehicle care and maintenance CAUTION Tires that do not have arrows showing rotation direction If the tires have arrows (A) indicating the correct direction of rotation, swap the front and rear tires on the left-hand side of the vehicle and the front and rear tires on the right-hand side of the vehicle sepa- Front rately.
Page 362 If flange nuts are used on your vehicle, change to tapered nuts when using snow tires with steel wheels. CAUTION Only Mitsubishi Motors genuine wheels should be used, because your vehicle is equipped with a tire Avoid the combined use of different types of tires. pressure monitoring system.
Page 363: Brake Pedal Free Play
Also check to see if the lever stays gripped by the ratchet after pulling. If the free play is not within these limits, take your vehicle to an authorized Mitsubishi Motors dealer or a repair facility of your choice for adjustment. WARNING...
Page 364 To be sure the emission-control system works properly, have your vehicle inspected and maintained by an authorized Mitsubishi Motors dealer or a repair facility of your choice fol- lowing the schedule in the “WARRANTY AND MAINTE- NANCE MANUAL”.
Page 365 If the fuel-vapor vent line is clogged or damaged, the fuel- plugs could cause engine damage, performance problems vapor mixture will escape, polluting the air. or radio noise. Have the system checked at an authorized Mitsubishi Motors dealer at the mileage specified in the “WARRANTY AND Fuel hoses MAINTENANCE MANUAL”.
Page 366: General Maintenance
Have these items checked if you tion regulation. notice a problem with them. See your authorized Mitsubishi Motors dealer for assistance, if you have any questions. Disc brake pads N00941600020 Good brakes are essential to safe driving.
Page 367 Vehicle care and maintenance Ball joint, steering linkage seals and drive shaft boots N00941800080 Check the following parts for damage and grease leaks: Ball joint boots of the front suspension and steering link- Bellows on both ends of the drive shaft Drive belt (for generator, power steering pump, air conditioning compressor) N00941900283...
Page 368 Vehicle care and maintenance Exhaust system Timing belt N00942200010 N00942300040 The timing belt should be replaced with a new one at the mile- WARNING age listed in the “WARRANTY AND MAINTENANCE MANUAL”. Carbon monoxide gas from your vehicle’s exhaust is poisonous.
Page 369: For Cold And Snowy Weather
The ventilation slots in front of the windshield should be kept In case of a melted fuse link, see your authorized Mitsubishi clear of leaves or brushed clear after a heavy snowfall, so that...
Page 370 Vehicle care and maintenance Fuses Engine compartment In the engine compartment, the fuse blocks are located as N00942800263 shown in the illustration. Fuse block location N00901000080 To prevent damage to the electrical system from short-circuit- ing or overloading, each individual circuit is equipped with a fuse.
Page 371 Vehicle care and maintenance Type A 1. Push the lock lever. 2. Remove the fuse block cover. WARNING Do not touch the electronic control module (D). The module surface can be too hot. Wait for the electronic control module to cool down before replacing a fuse.
Page 372 Vehicle care and maintenance Type B Type C 1. Push the lock lever. 1. Pull the lock lever. 2. Remove the relay box cover. 2. Open the cover. Fuse load capacities N00954800101 This fuse list shows the names of the electrical systems and their fuse capacities.
Page 373 Vehicle care and maintenance Passenger compartment fuse location table Symbol Electrical system Capacity Passenger compartment fuse location — — — — — — Radio 30 A Sunroof 20 A Rear window defogger 30 A Heater 30 A — — — —...
Page 374 Vehicle care and maintenance Engine compartment fuse location table Symbol Electrical system Capacity Back-up lights 7.5 A Type A Gauge 7.5 A Engine compartment fuse location Ignition coil 10 A — Spare fuse 20 A — Spare fuse 30 A —...
Page 375 Vehicle care and maintenance Symbol Electrical system Capacity Symbol Electrical system Capacity Ignition switch 40 A* Radio 10 A Power window control 30 A* Fuel pump 15 A Front fog lights/ Windshield wiper 30 A 15 A Daytime running lights *: Fusible link Heated seat 20 A...
Page 376 Vehicle care and maintenance Type B Type C Engine compartment fuse location Engine compartment fuse location Front Front Symbol Electrical system Capacity Symbol Electrical system Capacity Condenser fan motor 20 A* Radio 40 A* *: Fusible link *: Fusible link Some fuses may not be installed on your vehicle, depend- Some fuses may not be installed on your vehicle, depend- ing on the vehicle model or specifications.
Page 377: Fuse Replacement
Vehicle care and maintenance Identification of fuse Fuse replacement N00901100065 N00954900043 1. Before replacing a fuse, always turn off the electrical item Capacity Color connected to the fuse and turn the ignition key to the “LOCK” position. 7.5 A Brown 2.
Page 378 If the fuse is not blown, something else must be causing the problem. Contact an authorized Mitsubishi Motors dealer or a repair facility of your choice to have the problem checked.
Page 379: Replacement Of Light Bulbs
If you are unsure of how to perform the work as required, it is recommended that these procedures be performed by an authorized Mitsubishi Motors dealer or a repair facility of your choice. Be careful not to scratch the vehicle body when removing a light and lens.
Page 380 Vehicle care and maintenance Bulb capacity Outside N00950300746 N00943000044 The bulb should only be replaced with a new bulb with the Front same rating and type. The type and rating are listed on the base of the bulb. Wattage or ANSI Trade No.
Page 381 Vehicle care and maintenance NOTE Rear The high-mounted stop light uses LEDs rather than bulbs. For repair and replacement, contact an authorized Mitsubishi Motors dealer or a repair facility of your choice. Inside N00950400532 Wattage or ANSI Trade No. Description...
Page 382 Vehicle care and maintenance Headlights 2. Depress the tab (C) on the harness connector and pull the harness connector toward you to remove it. N00943100856 1. When replacing the headlight bulb on the left side, remove the relay box. Pull the relay box (B) upward while pressing the tab (A).
Page 383 Vehicle care and maintenance 3. Remove the locking cap (D) by turning it counterclock- 4. Remove the headlight bulb (E) with holder. wise. 5. To install the bulb, perform the removal steps in reverse. 7-48...
Page 384 N00943200121 The alignment of the headlights should be checked by an Handle halogen light bulb with care. The gas inside authorized Mitsubishi Motors dealer or a repair facility of your a halogen light bulb is highly pressurized, so drop- choice.
Page 385 Vehicle care and maintenance Front turn-signal and parking lights Front side-marker lights N00917300424 N00943400282 1. Turn the bulb socket counterclockwise to remove it. And 1. Turn the bulb socket counterclockwise to remove it. And remove the bulb from the socket by turning it counter- remove the bulb from the socket by pulling out.
Page 386 Vehicle care and maintenance Front fog lights (if so equipped) 2. Remove the socket and bulb assembly (D) by turning it counterclockwise. N00943600691 1. Remove the clips (A) and screws (B), then remove the cover (C). 7-51...
Page 387 Vehicle care and maintenance 3. Pull part (E) in the direction of the arrow (F) to undo the CAUTION lock, thereby freeing the fog light bulb from the connec- Handle halogen light bulb with care. The gas inside tor. a halogen light bulb is highly pressurized, so drop- ping, knocking, or scratching a halogen light bulb can cause it to shatter.
Page 388: Rear Combination Lights
Vehicle care and maintenance Rear combination lights 2. Remove each socket and bulb assembly by turning it counterclockwise. N00943700416 1. Open the lid. Partially take off the trim cover (A). B- Rear turn-signal light Remove the bulb by pulling it out. C- Tail and stop light Remove the bulb by pulling it out.
Page 389 Vehicle care and maintenance Back-up lights 2. On vehicles equipped with the cover, remove the clips (C) by prying with a straight blade (or minus) screwdriver, N00901200053 1. Open the trunk lid. and remove the cover (D). On vehicles equipped with the trunk lid grip, remove the screws (A), and remove the trunk lid grip (B).
Page 390 Vehicle care and maintenance 3. Remove the socket and bulb assembly by turning it coun- 4. Remove the bulb by pulling it out. terclockwise. E- Back-up light 7-55...
Page 391 The high-mounted stop light uses an LED instead of a hole, then firmly press the cap portion (G). bulb. Check with an authorized Mitsubishi Motors dealer or a repair facility of your choice when the light needs to be repaired or replaced.
Page 392: License Plate Light
Vehicle care and maintenance License plate light 2. On vehicles equipped with the cover, remove the clips (C) by prying with a straight blade (or minus) screwdriver, N00944000373 1. Open the trunk lid. and remove the cover (D). On vehicles equipped with the trunk lid grip, remove the screws (A), and remove the trunk lid grip (B).
Page 393 Vehicle care and maintenance 3. Open the trunk lid. 4. Remove the bulb by pulling it out. Remove the socket and bulb assembly by turning it coun- terclockwise. 5. To install the bulb, perform the removal steps in reverse. 7-58...
Page 394 Have the glove compartment light bulbs replaced at an autho- 1. Insert the tip of a screwdriver at the edge of the lens, pry rized Mitsubishi Motors dealer or a repair facility of your gently to remove the lens, and then remove the bulb from choice.
Page 395: Trunk Room Light
Vehicle care and maintenance Trunk room light Vanity mirror lights (if so equipped) N00944800081 N00952800064 1. Pull both clips (A) away from the center as shown and 1. Insert the tip of a screwdriver at the edge of the lens, pry remove the light unit.
Page 396 If you are not sure, contact an authorized Mitsubishi Motors dealer for help in choosing these materials. CAUTION Cleaning products can be dangerous. Some are poi- sonous.
Page 397: Cleaning The Inside Of Your Vehicle
Vehicle care and maintenance Cleaning the inside of your vehicle Upholstery N00945500030 N00945200037 1. To maintain the value of your new vehicle, maintain the After washing the inside of your vehicle with any cleaner, wipe upholstery carefully and keep the interior clean. it dry in a shady, well ventilated area.
Page 398: Cleaning The Outside Of Your Vehicle
Vehicle care and maintenance The genuine leather surface can be damaged if brushed Cleaning the outside of your vehicle with a nylon or synthetic fiber brush. N00945700045 Organic solvents such as benzine, alcohol, gasoline, acid To protect your vehicle’s finish, wash it often and thoroughly. or alkaline solvents can discolor the genuine leather sur- If desired, you may wax your vehicle using a nonabrasive auto- face and should not be used.
Page 399 Vehicle care and maintenance Take special care to remove mud or other debris which could CAUTION trap and hold salt and moisture. After washing your vehicle, wipe off all waterdrops from the When washing the underside of your vehicle or the rubber parts around the doors to prevent the doors from freez- wheels, wear a pair of gloves to protect your hands.
Page 400 Vehicle care and maintenance number for your vehicle can be found on the vehicle informa- CAUTION tion code plate in the engine compartment. Do not use gasoline, kerosene, benzene or paint thin- ners to remove road tar or other dirt from the vehi- cle surface.
Page 401 Vehicle care and maintenance Cleaning plastic parts Aluminum wheels (if so equipped) N00946300208 N00946500167 Use a sponge or chamois to clean these parts. 1. Remove dirt using a sponge while sprinkling water on the If vehicle wax sticks to a gray or black rough surface of the wheel.
Page 402: Engine Compartment
Vehicle care and maintenance Wiper blades Engine compartment N00946700013 N00947000042 Use a soft cloth and glass cleaner to remove grease, dead Never spray or splash water on the electrical components in the insects, etc., from the wiper blades. engine compartment, as this may cause damage. Replace the wiper blades when they no longer clean the Do not allow any nearby parts (such as plastic parts) come into windshield and rear window properly.
Page 404: Customer Assistance/ Reporting Safety Defects
Customer assistance/Reporting Safety Defects Consumer information (For vehicles sold in U.S.A.) ....8- Reporting Safety Defects ....8- Important facts to know in case of an accident .
Page 405 Customer assistance/Reporting Safety Defects Consumer information (For vehicles sold in WARNING U.S.A.) The traction grade assigned to this tire is based on N01047100100 straight-ahead braking traction tests, and does not This information is provided in compliance with the require- include acceleration, cornering, hydroplaning, or ments of the National Highway Traffic Safety Administration, peak traction characteristics.
Page 406: Reporting Safety Defects
1-888-327-4236 (TTY: 1-800-424-9153); Ottawa, Ontario K1A 0N5 go to http://www.safercar.gov; or write to: To contact Mitsubishi Motor Sales of Canada, Inc. call 1- 888-57- MITSU (1-888-576-4878) or write to: NHTSA Headquarters 1200 New Jersey Avenue, SE Mitsubishi Motor Sales of Canada, Inc.
Page 407: Specifications
Key information to discuss with your insurance a choice. So, if you want genuine Mitsubishi Motors parts, you may have to specifically request them. Make certain your company insurance company understands imitations are not to be used in Understand your repair estimate before approving repairs.
Page 408 Specifications Vehicle labeling ......9- Vehicle dimensions ......9- Vehicle weights .
Page 409: Vehicle Labeling
Specifications Vehicle labeling Engine serial number The engine serial number is stamped on the cylinder block as N01147400638 Keep a record of the vehicle identification number. This infor- shown in the illustration. mation will assist the police if your vehicle is stolen. *- Front of the vehicle 1 - Vehicle emission control information label The vehicle emission control information label is affixed on the...
Page 410 Specifications Tire and loading information placard Type 1 N01148100384 The tire and loading information placard is located on the driver’s door sill. Type 2 A- Vehicles sold in U.S.A. and Canada (Type 1) B- Vehicles sold in Canada (Type 2)
Page 411: Certification Label
Specifications Certification label Vehicle dimensions N01148200141 N01147500495 The certification label is located on the driver’s door sill. Overall length 191.1 in (4,853 mm) Overall width 72.4 in (1,840 mm) Vehicles with 57.4 in (1,458 mm) 16 inch tires Overall height Vehicles with 57.7 in (1,465 mm) 18 inch tires...
Page 412: Vehicle Weights
Specifications Vehicle weights N01147600773 Gross vehicle weight rating 4,376 lb (1,985 kg) Front 2,337 lb (1,060 kg) Gross axle weight rating Rear 2,072 lb (940 kg) Vehicle capacity weight 827 lb (375 kg) Seating capacity 5 persons GVWR: maximum total weight (load) limit specified for the vehicle GAWR: maximum weight (load) limit specified for the front or rear axle Seating capacity: the number of maximum occupants...
Page 413: Engine Specifications
Specifications Engine specifications N01147700484 Engine model 4G69 Engine displacement 145.1 CID (2,378 cm³) No. of cylinders and cylinder arrangement 4 in-line Bore 3.43 in (87.0 mm) Stroke 3.9 in (100.0 mm) Compression ratio 188.6 °F (87.0 °C) Thermostat valve opening temperature Spark plugs LZFR6AI Spark plug gap...
Page 414: Tires And Wheels
NOTE Contact an authorized Mitsubishi Motors dealer for details on the combination used on your vehicle. These tires satisfy vehicle loading conditions described in this owner’s manual.
Page 415 If these oils are not available, an API classification SM can Oil filter .32 qt (0.3 L) be used. Power steering As required Genuine Mitsubishi Power Steering Fluid Automatic transaxle 8.1 qt (7.7 L) DIAMOND ATF SP III Brake As required...
Page 416 Alphabetical index AM/FM electronically tuned radio with CD player-Type 1 5- AM/FM/Satellite electronically tuned radio with CD Accessory boxes 3-131 autochanger-Type 3 5-37 Accessory (installation) 1-7 Handling of compact discs 5-68 Active stability control 3-51 Steering wheel remote control switch 5-62 ASC indicator 3-54 Automatic transaxle 3-39 ASC OFF indicator 3-54...
Page 417 Alphabetical index Parking brake lever stroke 7-28 Pedal 3-47 Pedal free play 7-28 Defogger (rear window) 3-90 Power brakes 3-48 Digital clock 3-123 Service brake 3-47 Dimensions 9-4 Warning light 3-78 Dimmer (high/low beam change) 3-83 Break-in recommendations 3-2 Disc brake pads 7-31 Bulb capacity 7-45 Dome light 3-129 Capacity 7-46...
Page 418 Alphabetical index Oil and oil filter 7-6 Capacity 7-45 Overheating 6-5 Fuel Serial number 9-2 Fuel economy 4-2 Specifications 9-6 Fuel gauge 3-75 Error codes 5-64 5-66 Fuel hoses 7-30 Exhaust system 7-33 Low-fuel warning light 3-75 Modification/alterations to the electrical or fuel systems 1-8 Tank capacity 9-8 Fuel selection 1-2 Filling the fuel tank 1-4...
Page 419 Alphabetical index Hazard warning lights 3-78 Head restraints 2-12 Headlights Jack 6-8 Capacity 7-45 Storage 6-7 Dimmer 3-83 Jump-starting the engine 6-2 Headlight flasher 3-84 Switch 3-81 High beam indicator 3-78 Key reminder buzzer 3-14 3-35 High-mounted stop light Keyless entry system 3-7 Capacity 7-45 Keys 3-2 ®...
Page 420 Alphabetical index Odometer 3-73 AM/FM electronically tuned radio with CD player-Type 1 5- Engine oil 7-6 AM/FM/Satellite electronically tuned radio with CD Oil pressure warning light 3-80 autochanger-Type 3 5-37 Operation under adverse driving conditions 6-23 General information about your radio 5-72 Outside rearview mirrors 3-32 Reading light Overhead console control switch 3-93...
Page 421 Alphabetical index Heated seats 2-10 How the Supplement Restraint System works 2-42 Rear seat 2-11 Servicing 2-60 Seats and restraint systems 2-3 Warning light 2-47 Seat belt 2-15 Adjustable seat belt shoulder anchor 2-22 Child restraints 2-28 Tachometer 3-73 Maintenance and inspection 2-38 Tail lights Pre-tensioner 2-26 Capacity 7-45...
Page 422 Alphabetical index Traction control function 3-52 Fluid 7-13 Trailer towing 4-13 Switch 3-89 Trip odometer 3-73 Washer fluid 9-8 Trunk lid 3-16 Waxing 7-64 Trunk room light Weights 9-5 Capacity 7-46 Wheel Replacement 7-60 Covers 6-19 Turn signal light Specification 9-7 Indicators 3-78 Wiper Lever 3-84...
Page 423 How to calculate your gasoline mileage You can calculate your miles-per-gallon or kilometers-per-litre 3. Refill the fuel tank. Record the odometer mileage again, by using the following process: as well as the gallons/litres of fuel used. 4. Subtract the first mileage number from the second number 1.
Page 424: Maintenance Record
NOTE Name of Owner Date of Purchase Address of Owner Model of Vehicle Name and Address of Dealer Vehicle Identification Number Maintenance record Kilometers Service Performed Date Inspection and Maintenance Item Miles...

Mitsubishi Galant Owner's Manual

Quick Links

Introduction

Related Manuals for Mitsubishi Galant

Summary of Contents for Mitsubishi Galant

Table of Contents