Related Manuals for Drive DeVilbiss Selectis
Summary of Contents for Drive DeVilbiss Selectis
- Page 1 Shell seats Integra & Selectis USER GUIDE Integra Selectis Plus d’informations : More information : More informations :...
-
Page 2: Table Of Contents
8 - YEARLY MAINTENANCE, REPAIRING, WARRANTY 8.1 - Main procedures................p 6 8.2 - Accessories...................p 6 Thank you and congratulations for buying a Drive Devilbiss 8.3 - Storage...................p 6 Healthcare France chair. Understanding well and maintaining 8.4 - Chair service life and end of life..........p 6 regularly the chair will prolong its service life. -
Page 3: Reuse
Integra et Selectis USER AND MAINTENANCE MANUAL FOR SHELL SEATS 1.4) Reuse In case another user will reuse this chair, this latter should be cleaned, Product variants: setup configuration/ disinfected, and totally revised by an approved engineering centre. seat width/... -
Page 4: Safety Instructions
Integra et Selectis USER AND MAINTENANCE MANUAL FOR SHELL SEATS III - SAFETY INSTRUCTIONS may affect the seat behaviour. Should the case arise, please contact the distributor. l The presence of long distance transmitters and receivers, such The footrest (option) should always touch the floor when as diffusion transmitters (TV and radio antenna towers), amateur the chair is in trendelenburg (tilted forwards). -
Page 5: For Maximum Stability
Integra et Selectis USER AND MAINTENANCE MANUAL FOR SHELL SEATS The first time you use the seat belt: Shell in maximum forward position l Standing position transfer seat: The belt is under the wooden seating plate. To release it, tilt the transfer seat to the maximum (see 10.6), pull the ends to remove the staples, fold the straps of... -
Page 6: Maintenance
8.3) Storage Only the original parts provided by Drive DeVilbiss Healthcare France can be used to repair a Drive DeVilbiss Healthcare France Before storing the chair for a long period, clean it totally, and chair. Any change or repair performed with parts coming from check its performance. -
Page 7: Warranty Conditions
11 - E-125-mm casters equipped with brakes (x3) + 1 directional maintained and completed during every procedure. caster + 1 roller (INTEGRA) Two 12,5’’-tyre rear wheels and two 6’’-front wheels (SELECTIS) IX - OPTIONS AND TECHNICAL 12 - Mains power supply (types M.T. and E.T.) INFORMATION 9.1) General presentation... -
Page 8: Options
Integra et Selectis USER AND MAINTENANCE MANUAL FOR SHELL SEATS Power requirements (if applicable) Seat Overall width Sizes width (without shelf) Mains power supply: l Mains 100-240V AC 50-60Hz 1.2A * Type MT and ET: Integra Selectis only those 3 sizes... -
Page 9: Seat Height
For the different positions, see the values in the table page 8. or by the wheels. Always unplug the power supply cord The height adjustment procedure is the same as with Selectis. when the chair is not used. Position 1 incompatible with POSTURE model. -
Page 10: Transfer Aid
Integra et Selectis USER AND MAINTENANCE MANUAL FOR SHELL SEATS 10.6) Legrest inclination With the remote control, it is possible to tilt the chair backwards and forwards, but it is also possible to lift the seat back for easier M., M.T., and E.T. versions, legrest with automatic inclination transfer. -
Page 11: 3-Point Pelvic Belt And Harness
Integra et Selectis USER AND MAINTENANCE MANUAL FOR SHELL SEATS 10.9) -point pelvic belt and harness Insert the A shelf support into the sleeve located under the seat, (option) the tube C has to be in support on the foot, position the mounting hole in front of the hole adapted to the chair dimensions. - Page 12 Integra et Selectis USER AND MAINTENANCE MANUAL FOR SHELL SEATS 10.13.a First use ● Absolutely do not expose the battery to any heat source such as a heater, or even to sunlight trough a window. CAUTION Carefully read the following instructions: ●...
Need help?
Do you have a question about the Selectis and is the answer not in the manual?
Questions and answers