Related Manuals for Holy Stone HS720
Summary of Contents for Holy Stone HS720
- Page 1 Instructions For Use Gebrauchsanweisung V 1.0 HS720 eu@holystone.com (EU) usa@holystone.com (USA) jp@holystone.com (JP) ca@holystone.com (CA) +1(855) 888-6699 www.holystone.com...
- Page 2 English 01-43 Deutsch 44-83...
-
Page 3: Table Of Contents
Contents 1.0 Disclaimer&Warning ..................2.0 Safety Guidelines ..................3.0 Maintenance ....................4.0 Package Contents ..................5.0 Drone’s Details ....................6.0 Transmitter Details 6.1 Transmitter Functions ................6.2 LCD Screen Functions ................6.3 Low Battery Warning ................6.4 Mode Switch ..................... 7.0 Installation 7.1 Drone Battery .................. - Page 4 10.0 Functions Details 10.1 Camera Angle Adjustment ............... 10.2 Return to Home ..................10.3 Image Positioning System ..............11.0 APP Operation Instruction 11.1 Operation Interface ................11.2 Setting Parameter ................11.3 Follow Me .................... 11.4 TapFly ....................11.5 Point of Interest .................. 11.6 Take Photo/ Video ................
-
Page 5: Disclaimer&Warning
. You agree to use this product only for purposes that are proper and in accordance with local regulations, terms and all applicable polices and guidelines Holy Stone may make available. 2. When using this product, please be sure to strictly abide by the specifica- tion requirements and safety guidelines stated in this document. - Page 6 ④ Please do a thorough check of the product before each use. Inspect the integrity of the parts, any signs of cracks and wear of the propeller, battery power and effectiveness of the indicator, etc. If after doing a complete check any issues are found, please refrain from using the product until the issue has been resolved.
- Page 7 2.3 Operation Requirements： ① Please don’t use this product to follow any moving vehicles . ② During the flight, only turn off the motor in case of an emergency. ③ As battery becomes low return the drone back to your starting point. ④...
- Page 8 ⑦ It is recommended to only use the USB charging cable that comes with the drone to charge the battery. ⑧ Don't connect the battery directly to wall outlets or car cigarette -lighter sockets. ⑨ Don't attempt to disassemble or modify the battery in any way. ⑩...
-
Page 9: Maintenance
3.0 MAINTENANCE ① Clean the product after each use with a clean, soft cloth. ② Avoid prolonged exposure to direct sunlight and avoid buildup of heat on the drone. ③ This device is not waterproof and must not be submerged in water under any circumstance. -
Page 10: Package Contents
×1 ×1 Drone Transmitter Drone Battery ×4 ×1 ×1 USB Charging Propeller Charger Hub Cable Instructions For Use Gebrauchsanweisung V 1.0 HS720 usa@holystone.com (USA) eu@holystone.com (EU) ca@holystone.com (CA) jp@holystone.com (JP) ×1 ×1 +1(855) 888-6699 www.holystone.com Screwdriver Instructions For Use -06-... -
Page 11: Drone's Details
5.0 DRONE’S DETAILS Propeller A Propeller B Propeller B Short-press: Turn on Long-press: Turn off Propeller A HD Camera Lights Vision Positioning Lens Battery Battery Indicator -07-... -
Page 12: Transmitter Details
6.0 TRANSMITTER DETAILS 6.1 Transmitter Functions Antenna Built-in Phone Holder One Key Takeoff/ Landing Return to Home Right Joystick Left Joystick Lock/ Unlock Power Switch LCD Screen Folded Handle - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Camera Angle Adjustment Short-press: Take Photos... - Page 13 •GPS Mode Switch When turning on the transmitter, the default mode is the GPS Mode. Turn off GPS by sliding GPS switch. Check the icon “ ” or “ ”on the LCD screen to confirms GPS status. •Return to Home (RTH) Press the button to start the RTH, the transmitter makes a beep sound and the drone will fly back to the recorded Home Point.
-
Page 14: Lcd Screen Functions
6.2 LCD Screen Functions Return to Home (RTH) Signal Strength Drone Transmitter Battery Level Battery Level Photo/ Video Distance Against High/ Low Home Point Speed Mode Amount Altitude against Transmitter GPS Mode Home Point Throttle Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6.3 Low Battery Warning Pic. -
Page 15: Mode Switch
6.4 Mode Switch 6.4.1 MODE 2 (Left hand throttle MODE 2 will be default setting.) Left Joystick Right Joystick Forward Ascend Descend Down Backward Down Left Right Right Left Fly to Fly to Rotate Left Rotate Right Left Right - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6.4.2 MODE 1 ①... -
Page 16: Installation
7.0 INSTALLATION 7.1 Drone Battery Installation: Push the battery into the battery compartment at the rear of the drone. Make sure that you hear a click sound indicating the battery is firmly installed. Attention: The battery should be installed firmly, failure to do so may affect the flight safety of your drone. -
Page 17: Install Tf Card
7.2 Install TF Card HEAD As shown in the above figure place drone on the backside and slide the TF card (Not included) into the TF slot on the left side of the fuselage. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7.3 Transmitter Battery ②... -
Page 18: Propellers
7.4 Propellers Installation HEAD The drone will not fly unless the correct propeller is installed on the correct motor shaft. See illustration above. An “A” “B” is printed on the back of each propeller. Lock the propeller to the motor shafts with screws rotating each screw clockwise. -
Page 19: Phone Holder
7.5 Phone Holder 1. Pull out the mobile phone holder upwards completely (Pic. 3). Pic. 3 2. Tilt the holder 30 degrees towards you and then you will hear a click sound (Pic. 4). Pic. 4 3. Rotate and fix the support board in place (Pic. -
Page 20: Charging
8.0 CHARGING USB Adapter (5V/0.5-2.0A) Charging Indicator Light ① Power Bank Power Indicator Light Charging Indicator Light ② ① Connect the Battery, Charger Hub and USB Charging Cable. ② Connect the USB Charging Cable with Power Bank or a USB Adapter (5V/ 2.0A ) for charging. -
Page 21: Operation Guide
9.0 OPERATION GUIDE 9.1 Download APP Android APP on Google play Scan the QR code, corresponding to either App Store™ or Google™ Play Store and download the “ Ophelia GPS ” application for free. Required Operating Systems: iOS v8.0 and later / Android v4.3 and later 9.2 Connect to Wi-Fi HolyStoneFPV-****** Connect your smart phone to the Wi-Fi network created by the drone. -
Page 22: Paring
All of the operations shown in this manual are demonstrated using MODE 2. 9.3 Pairing ① Simultaneously hold the “ “ button and slide the power switch to the right to power on the transmitter. It will beep 2 times and the indicator light “... -
Page 23: Initialization Detection
9.4 Initialization Detection HEAD Place the drone on the level surface and it will enter the Initialization Detection. The red, green and yellow LED lights of the drone will alternate flickering for about 7 seconds to complete the initial detection. When completed, the transmitter will sends out “Di Di”... -
Page 24: Unfolding The Drone
（ ） Step 2: Hold the drone vertically and rotate the drone in 3 complete circles. When completed the front Red lights and rear Yellow lights will turn solid and “ ” on the LCD screen changes from slow flash to disappear. Attention: ・If the GPS receives a signal from 7 or more satellites the indicator light on the drone will change to Red in the front and Green in the rear. -
Page 25: Unlocking
9.7 Unlocking 9.7.1 Unlocking the Motor Please unlock the motor before take-off. Short press the red button “ ” . The motors rotate and the drone is unlocked. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9.7.2 Locking the Motor Pic. -
Page 26: One Key Takeoff/ Landing
9.8 One Key Takeoff/ Landing ① ② Landing Take-off ① After unlocking the drone, short press the “ ” button, the drone will automatically take off and hover at 5 feet altitude. ② When the drone is flying, short press the “ ”... -
Page 27: Return To Home
10.2 Return to Home (RTH) ・The Return to Home function brings the drone back to the last record- ed Home Point. ・The Home Point is the location at which the drone takes off or the GPS receives a signal from 7 or more satellites for the first time during flight. The current position of the drone will be recorded as the Home Point. - Page 28 10.2.3 Low Voltage RTH ① When the drone's rear lights flash slowly, the “ ” symbol is displayed on the screen of the transmitter, the First Low Voltage RTH will be triggered. And the drone will return automatically in the following two conditions: this time, the drone can only fly within a safe range of the height no more than 98 feet and the distance no more than 328 feet .) H＞98 feet...
- Page 29 ② If the drone’s rear lights begin to flash rapidly the “ “ symbol will be displayed on the transmitter screen and the transmitter will emit a “Di..., Di...” alert. The Second Low Voltage RTH is automatically triggered. H＞50 feet a.
-
Page 30: Image Positioning System
10.3 Image Positioning System ① The Image Positioning System consists of a camera ① module, which acquires the position information of the drone through visual images to ensure precise positioning and safe flight of the drone. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - The Image Positioning System is typically used in indoor environment when GPS is weak or unavailable. - Page 31 available, your drone will switch to Gesture Mode automatically. Be cautious to operate the drone in the following situation: 1. Fly fast at an altitude below 0.5m. 2. Fly over monochrome surfaces (like pure black, pure red, pure red and pure green).
-
Page 32: App Operation Instruction
11.0 APP OPERATION INSTRUCTION 11.1 Operation Interface 180° Screen Hide Photos 3D VR GPS Signal Rotation On/ Off RTH Home Drone Transmitter Setting Altitude Point Distance Battery Level Battery Level Transmitter Signal Shutter Photo/ Video Return Signal Strength Strength Button Switch Point of Follow-me... -
Page 33: Setting Parameter
11.2 Setting Parameters Click the “ ” icon to enter the setting interface (as shown in the figure above), you can set a limited flight range: 1. Maximum flight altitude: 50~390 feet/ 15~120 m. (The default flight altitude is 390 feet.) 2. -
Page 34: Follow Me
11.3 Follow Me When the Follow Me function is enabled, the drone will follow the GPS in your smart phone to follow you wherever you go. 1. Ensure the drone's flight range is within 15~95 feet. 2. Click the“ ” icon on the app interface, and click “ YES ” in the prompt box to enter the Follow Me function —... -
Page 35: Tapfly
11.4 TapFly It is recommended to enlarge the map if you want to use TapFly. 1. Click the“ ” icon on the app interface, and click “ YES ” in the prompt box to enter the TapFly function. MODE 1: Click the“ ”... -
Page 36: Point Of Interest
11.5 Point of Interest 1. Click the“ ” icon on the app interface, and click “ YES ” in the prompt box to enter the Point of Interest function. 2. The drone will record it’s flight position the moment you enter this function as the point of interest. -
Page 37: Take Photo/ Video
11.6 Take Photo/ Video 1. Click the “ ” icon to switch between photo and video mode. 2. When the shutter button is “ ”, click once to take a photo. 3. When the shutter button is “ ”, click once to start recording, and click again to stop recording. -
Page 38: Drone Status Indicator
12.0 DRONE STATUS INDICATOR Indicator Status Indicator Status Meanings Front and rear lights alternate flashing The drone is not connected to the yellow. transmitter. Red, green and yellow lights flashing Drone is currently in Initialization Detec- and alternate. tion status. Front light turns solid red, rear light No GPS signal or weak GPS signal. -
Page 39: Specifications
13.0 SPECIFICATIONS DRONE Model: HS720 Weight: 460g / 16.2oz Flight Time: 26 minutes Operating Temperature Range: 32° to 104°F Dimensions: 173 x 104 x 56 mm (Folded) 336 x 370 x 56 mm (Unfolded) DRONE BATTERY Capacity: 2800 mAh Voltage: 7.4 V Battery Type: Li-Po Energy: 20.72 Wh... - Page 40 CAMERA Camera frequency: 5 GHz Video/ Photo Resolution: 2K (2048×1152p) Lens: FOV 110° FPV Distance: 656~1312 feet (outdoor and unobstructed) Photo: JPEG Video: AVI / MP4 MAX Supported TF Cards: 32 GB (Not included) Controllable Range: Pitch: -90° to 0° Operating Temperature Range: 32°...
-
Page 41: Trouble Shooting
14.0 TROUBLE SHOOTING Problem Solution When the drone is powered on, The drone is in the gyroscope the indicator light keeps flashing calibration state. Please place the rapidly. drone on an flat and level surface. Place the drone on a flat, level The drone cannot hover after surface and repeat the gyro takeoff and tilts to one side. -
Page 42: General Information
16.0 GENERAL INFORMATION FCC Statement: Any Changes or modifications not expressly approved by the party respon- sible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interfer-... - Page 43 WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator &...
- Page 44 2) I'utillsateur de I'appareil doit accepterbrouillage radioélectrique subi meme si le brouillage est susceptible d'encompromettre le fonctionnement. mauvais fonctionnement de I'appareil. Cet appareil numériquie de la classe B est conforme à la norme NMB-003 du Canada. CAN NMB-3 (B) RF Exposure Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
- Page 45 BATTERY WARNING: 1. Failure to follow all the instructions may result in serious injury, irreparable damage to the battery and may cause a fire, smoke or explosion. 2. Always check the battery’s condition before charging or using it. 3. Replace the battery if it has been dropped, or in case of odor, overheat- ing, discolouration, deformation or leakage.
- Page 46 We, Xiamen Huoshiquan Import & Export CO., LTD hereby, declare that the essential requirements compliance with the Directive 2014/53/EU, the RoHS Directive 2011/65/EU and Safety Directive 2009/48/EC have been fully fulfilled on our product with indication below: Product Name: REMOTE CONTROL MODEL/RADIO CONTROLLED Model/Mark : HS720/HOLYSTONE -42-...
- Page 47 The Statement of compliance is available at the following address: http://www.holystone.com/Download/CE/HS720_EU_DOC.pdf This product can be used across EU member states. MANUFACTURER INFORMATION Manufactured by Xiamen Huoshiquan Import & Export CO., LTD Room 703,No. 813-2 Xiahe Road, Siming District, XIAMEN, China +1(855) 888-6699 FAA REGISTRATION: PLEASE FOLLOW ALL FEDERAL, STATE AND LOCAL FAA LAWS.