Advertisement

Instructions For Use
Gebrauchsanweisung
V 2.0
+1(855) 888-6699
usa@holystone.com (USA)
ca@holystone.com (CA)
HS720R
eu@holystone.com (EU)
www.holystone.com
6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HS720R and is the answer not in the manual?

Questions and answers

Paul Blears
January 24, 2025

Unable to adjust camera view up or down

1 comments:
Mr. Anderson
February 10, 2025

You can adjust the camera view up or down on the Holy Stone HS720R using the gimbal dial on the controller. However, the gimbal only moves between 0 degrees and 70 degrees, so you cannot point the camera straight down at the ground.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for Holy Stone HS720R

  • Page 1 Instructions For Use Gebrauchsanweisung V 2.0 HS720R +1(855) 888-6699 www.holystone.com usa@holystone.com (USA) eu@holystone.com (EU) ca@holystone.com (CA)
  • Page 2 English 01-47 Deutsch 48-91...
  • Page 3: Table Of Contents

    Contents 1.0 Disclaimer & Warning................2.0 Safety Guidelines..................3.0 Maintenance....................4.0 FAA Flight Regulations................5.0 Package Contents..................6.0 Drone Details....................7.0 Transmitter Details 7.1 Transmitter Functions................7.2 Joystick Mode..................8.0 Charging ....................... 9.0 Preparation Before Flight 9.1 Download APP ..................9.2 Arms......................
  • Page 4 11.0 Return to Home 11.1 Smart RTH..................... 11.2 Failsafe RTH..................11.3 The First Stage of Low Voltage RTH..........11.4 The Second Stage of Low Voltage RTH........12.0 APP Operation Instruction 12.1 Operation Interface................12.2 Beginner Mode................... 12.3 Follow Me..................... 12.4 Point of Interest.................. 12.5 Take Photo/Record Video ..............
  • Page 5: Disclaimer & Warning

    1.0 DISCLAIMER & WARNING 1. Please read this Disclaimer & Warning and Safety Guidelines carefully before using our product. This product is not recommended for people under the age of 16. By using this product, you hereby agree to this disclaimer and signify that you have read it fully.
  • Page 6 ④ Please perform a thorough check of the product before each use. Inspect the integrity of the parts, any signs of cracks and wear off on the propellers, battery power and effectiveness of the indicator, etc. If there is any problem found after checking the drone, please refrain from using it until the problem is resolved.
  • Page 7 2.3 Operation Requirements ① DO NOT use this product to follow any moving vehicles. ② During the flight, turn off the motors only in case of an emergency. ③ When the battery runs low, return the drone back to your starting point. ④...
  • Page 8 ⑥ If the device is not going to be used for an extended period of time, please remove batteries to prevent potential damage to the drone from battery leakage. ⑦ Only use the USB charging cable that comes with the drone to charge the battery.
  • Page 9: Maintenance

    3.0 MAINTENANCE ① Clean the drone after each use with a clean, soft cloth. ② Avoid prolonged exposure to direct sunlight and avoid buildup of heat on the drone or batteries. ③ This device is not waterproof. DO NOT allow it to get wet or submerged in water.
  • Page 10: Package Contents

    5.0 PACKAGE CONTENTS Drone Transmitter Drone Battery USB Charging Propeller Screwdriver Cable Instructions For Use Gebrauchsanweisung V 2.0 HS720R www.holystone.com +1(855) 888-6699 usa@holystone.com (USA) eu@holystone.com (EU) ca@holystone.com (CA) Instructions For Use -06-...
  • Page 11: Drone Details

    6.0 DRONE DETAILS Propeller A Propeller B Propeller B Propeller A Gimbal and Camera Front LED - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Battery Level Indicators Power Switch Drone Status Indicator...
  • Page 12: Transmitter Details

    7.0 TRANSMITTER DETAILS 7.1 Transmitter Functions Antenna Phone Holder One Key Takeoff/ Landing Return to Home Left Joystick Right Joystick Unlocking the Motors/ Power Switch Emergency Stop (Long Press) (Long Press) Speed Switch Foldable Handle Transmitter Photo/Video Indicator Light Indicator Light Drone GPS Signal/Return Indicator Light...
  • Page 13 · You can check the current battery status of the transmitter by short pressing the power switch button once. Please fully charge the battery of the transmitter before use. When fully charged, the transmitter can work for 2.5 hours. · Long press the ( ) button to switch the GPS Mode on or off.
  • Page 14: Joystick Mode

    •Return to Home (RTH) Short press the RTH button ( ) to start the RTH, the transmitter makes a beep sound and the drone will fly back to the recorded Home Point. Short press the RTH button ( ) again to exit the RTH procedure and regain control of the drone.
  • Page 15: Charging

    8.0 CHARGING USB Adapter Charging time: about Charging time: about (5V/2A) 5 hours 1.5 hours (Not included) (Charging) (Fully Charged) (Charging) (Fully Charged) Connect the USB charging cable to a USB Adapter(5V/2A), and then connect with the charging port of the drone or transmitter. ·...
  • Page 16: Preparation Before Flight

    9.0 PREPARATION BEFORE FLIGHT 9.1 Download APP Android APP on Google Play Scan the QR code, corresponding to either App Store™ or Google Play™ Store and download the Ophelia FLY app for free. Required Operating Systems: iOS 9.0 or later/Android 5.0 or later. 9.2 Arms All arms of the drone are folded before the drone is packaged at the factory.
  • Page 17: Gimbal Cover

    9.3 Gimbal Cover As shown above, turn the drone over, press down on the edge of the gimbal cover to unlock the buckle, then push it out and take it away. ・Please remove the gimbal cover gently before powering on the drone.
  • Page 18: Drone Battery

    9.5 Drone Battery Installation: Push the battery into the battery compartment at the rear of the drone. Make sure that you hear a click sound, which indicates that the battery is firmly installed. ・Before installing the battery, please check if it has a detachable insulation pad/band.
  • Page 19: Propellers

    9.6 Propellers HEAD Installation: The drone will not fly unless the correct propeller is installed on the correct motor shaft. See the illustration above. An “A” “B” is printed on the back of each propeller. Lock the propeller to the motor shafts with screws.
  • Page 20: Antenna

    9.7 Antenna Strong Expand the two antennas on the transmitter before starting the flight. To get the best signal, position the antennas like a triangle, as depicted above on the right. The signal between the drone and the transmitter is most reliable when the transmitter is positioned toward the drone, as depicted above on the left.
  • Page 21: Foldable Handle

    9.8 Foldable Handle As shown above, expand the foldable handle on the transmitter separately. 9.9 Phone Holder Expand the phone holder and place your mobile phone in it. Adjust the clamp to secure your mobile phone. -17-...
  • Page 22: Flight

    10.0 FLIGHT All of the operations shown in this manual are demonstrated using MODE 2. · Pre-Flight Checklist 1. Make sure the transmitter, the mobile phone and the drone battery are fully charged. 2. Make sure the drone battery and the propellers are mounted securely. 3.
  • Page 23: Initialization Detection

    10.2 Initialization Detection HEAD First-time Use Non-first-time Use Place the drone on the level surface and it will enter the initialization detection. The drone status indicator will alternate between red, green and yellow. There are two possible scenarios: ・First-time Use: The drone status indicator will flash yellow. ・Non-first-time Use: The drone status indicator changes to green (yellow).
  • Page 24: Calibrating The Compass

    10.4 Calibrating the Compass The drone will perform a mandatory compass calibration before the initial flight. So you can skip step 1 if this is the first time you fly your drone. Step 1: As shown in the figure above, push both of the joysticks down to the bottom right corner at the same time to enter the compass calibration.
  • Page 25: Unlocking The Motors

    · To ensure a stable flight, we recommend that pilots perform a com- pass calibration before each flight. · DO NOT calibrate the compass in locations where magnetic interfer- ence may occur, such as close to magnetite deposits or large metallic structures such as parking structures, steel reinforced basements, bridges, cars, or scaffolding.
  • Page 26: One Key Takeoff/Landing

    10.6 One Key Takeoff/Landing Please unlock the motors before takeoff. ② ① Takeoff Landing ① Short press the ( ) button, the drone will automatically take off and hover at 3 ft. ② When the drone is flying, short press the ( ) button, the drone will automatically land on the ground.
  • Page 27: Return To Home

    11.0 RETURN TO HOME(RTH) ・The Return to Home function brings the drone back to the recorded Home Point. ・The default Home Point is the first location where the drone receives a strong GPS signal (the GPS Signal Indicator on the transmitter turns solid green at this point).
  • Page 28: The First Stage Of Low Voltage Rth

    11.3 The First Stage of Low Voltage RTH The First Stage of Low Voltage RTH is automatically triggered when the battery level displays ( ). At this time, the drone status indicator will start to flash red slowly, the transmitter will start to keep beeping, and the GPS Signal/Return Indicator Light will start to blink slowly.
  • Page 29: The Second Stage Of Low Voltage Rth

    H=98 ft Home Point D=984 ft < b. Flight Altitude 98 ft Flight distance 984ft ≥ If the drone is within the safe zone, it will not perform a Return to Home procedure. At this time, the pilot is free to operate the drone. 11.4 The Second Stage of Low Voltage RTH The Second Stage of Low Voltage RTH is automatically triggered when the battery level displays(...
  • Page 30 b.When the flight altitude is lower than 49 ft and the flight distance is larger than 49 ft, the drone will first ascend to 49 ft, fly back above the Home Point, then descend to the ground. H=49 ft Home Point D=49 ft b.
  • Page 31: App Operation Instruction

    12.0 APP OPERATION INSTRUCTION 12.1 Operation Interface Homepage: Tap this icon to return to the main menu. GPS Signal: Displays the current GPS signal strength. Drone Battery Level: Real-time display of the current battery level of the drone. Transmitter Battery Level: Real-time display of the current battery level of the transmitter.
  • Page 32 Flight Setting: Tap to enter the setting interface. Alter settings for flight height/distance, return altitude, etc. Follow Me Mode: Tap the icon and the drone can automatically follow the pilots according to the GPS positioning of the phone. Point of Interest: The drone will fly around a point. Return to Home: Tap to bring the drone back to the Home Point.
  • Page 33: Beginner Mode

    12.2 Beginner Mode Security Sensor Status Beginner Open novice mode by default, and turn it off to custom mode Mode Orbit Default 16ft Default semidiameter (16~164ft) Maximum Default Default 49ft distance (≥49ft) Maximum Default Default 49ft height (49~393ft) Default RTH altitude Default 49ft (49~164ft)
  • Page 34: Follow Me

    12.3 Follow Me When the Follow Me function is enabled, the drone will track your movement by following the GPS signal on your mobile phone. 1. Ensure the drone's flight range is within 16~98 ft. 2. Tap the ( ) icon first, then select the ( ) icon, and follow the prompt box to enter the Follow Me function —...
  • Page 35: Point Of Interest

    12.4 Point of Interest 1. Tap the ( ) icon first, then select the ( ) icon, and follow the prompt box to enter the Point of Interest function. 2. The moment you enter this function, the drone will record its current flight position as the “point of Interest”.
  • Page 36: Time-Lapse

    12.6 Time-lapse * Please be sure to insert a TF card before using time-lapse function. The drone can shoot time-lapse videos in four modes: Free, Dronie, Straight, and Circle. Free Mode: By setting the playback speed, the drone will take a number of photos to generate a time-lapse video.
  • Page 37: Tapfly

    Follow the steps below to generate time-lapse videos: 1. Entering: Tap the ( ) icon on the app interface to enter the time-lapse function. 2. Mode Selection: You can choose one of the following four modes: Free, Dronie, Straight, and Circle . 3.
  • Page 38 1. Tap on the map ( ) first, then tap the ( ) icon. Follow the prompt box to enter the TapFly function. MODE 1: Tap the ( ) icon on the app interface. Draw a line on the screen to create a flight path, tap ( ) icon to submit the path.
  • Page 39: Stabilization Function

    13.0 STABILIZATION FUNCTION 13.1 Altitude-Hold Function The drone is designed with an altitude-hold function to maintain its altitude after releasing the left joystick. (The left joystick will automatically spring back to the middle) 13.2 Optical Flow Positioning Optical Flow Module The Optical Flow Positioning System consists of a camera module, which acquires the position information of the drone through visual images to ensure precise positioning of the drone.
  • Page 40 The Optical Flow Positioning System is typically used in an indoor environ- ment when the GPS signal is weak or unavailable. It works best when the drone altitude is less than 10 ft. ・The precision of the Optical Flow Positioning System is easily affected by the light intensity and features of the surface textures.
  • Page 41: Status Indicator States

    ・Keep sensors clean at all times. ・The Optical Flow Positioning is only effective when the drone is within the altitude range of 10 ft. ・Make sure that the light is bright enough and the surface is with clear textures so that the Optical Flow Positioning can acquire the movement information through recognizing the ground textures.
  • Page 42 • Transmitter Status Indicator States Meanings Indicator Status Transmitter is paired with drone Solid or transmitter battery is fully charged Transmitter battery level is low Flash slowly or transmitter battery is charging Tranmitter Indicator Light Flash quickly Transmitter is pairing with drone Drone is connected with transmitter Solid Drone is disconnected with transmitter...
  • Page 43: Specifications

    15.0 SPECIFICATIONS DRONE Model: HS720R Weight: 389g/13.72oz Max Flight Time: 26 minutes (per battery) Operating Temperature Range: 32° to 104°F Size: 168*99*71mm(Folded) 305*238*71mm(Unfolded) DRONE BATTERY Capacity: 2950mAh Voltage: 7.7V Battery Type: Lithium-ion Polymer Battery Energy: 22.715Wh Charging Temperature Range: 41° to 104°F...
  • Page 44 GIMBAL Stabilization: 3-axis (tilt, roll, pan) Machanical Range: Tilt about ±30° Roll about ±30° Pan about ±30° Controllable Range: Adjusted angle of camera (up and down): about -70° to 0° CAMERA Operating Frequency: 5745-5825MHz Max Photo Resolution: 3840×2160P Max Video Resolution: 3840×2160P@30fps Lens Angle: FOV 140°...
  • Page 45: Contact Us

    16.0 CONTACT US Please do not hesitate to contact us if you need further support. usa@holystone.com (America) ca@holystone.com (Canada) eu@holystone.com (Europe) +1(855) 888-6699 Scan the code and chat live for online support Scan the code to start a WhatsApp chat with us -41-...
  • Page 46: General Information

    17.0 GENERAL INFORMATION FCC Notice: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interfer- ence that may cause undesired operation.
  • Page 47 WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator &...
  • Page 48 (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionne- ment. CAN NMB-003 (B) RF Exposure Radiation Exposure Statement: The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
  • Page 49 BATTERY WARNING: 1. Failure to follow all the instructions may result in serious injury, irreparable damage to the battery and may cause a fire, smoke or explosion. 2. Always check the battery’s condition before charging or using it. 3. Replace the battery if it has been dropped, or in case of odor, overheat- ing, discoloration, deformation or leakage.
  • Page 50 We, Xiamen Huoshiquan Import & Export CO., LTD hereby, declare that the essential requirements compliance with the Directive 2014/53/EU, the RoHS Directive 2011/65/EU and Safety Directive 2009/48/EC have been fully fulfilled on our product with indication below: Product Name: REMOTE CONTROL MODEL/RADIO CONTROLLED Model/Mark: HS720R/HOLYSTONE -46-...
  • Page 51 The Statement of compliance is available at the following address: http://www.holystone.com/Download/CE/HS720R_EU_DOC.pdf This product can be used across EU member states. MANUFACTURER INFORMATION Manufactured by Xiamen Huoshiquan Import & Export CO.,LTD Address: Unit 1, Room 501, Hongxiang Building, No.258 Hubin Nan Road, Siming District, Xiamen, China +1(855) 888-6699 MADE IN CHINA(CN)

Table of Contents

Save PDF