• do not use or light any appliance. • Always contact Dacor Customer Assurance with questions and • do not touch any electrical switch or use any electrical devices (incl. issues you cannot resolve. (See the contact info, facing page) the telephone) in your building.
Page 4
Important Safety Instructions General Safety Precautions WARNING To reduce the risk of fire, electric shock, or serious injury • Do not leave the cooktop unattended while in use to or death when using your appliance, follow basic safety avoid the possibility of a fire. precautions, including the following: •...
Important Safety Instructions Electrical Requirements Gas Supply Requirements • Ensure the cooktop is set up for the supplied gas type (Natural WARNING or LP). If using the cooktop above 4000 ft. (1219 m) elevation, ensure it is equipped for high-altitude use. (Such units have an To prevent an electric shock hazard, the power supply must meet the “H”...
Installation Specifications WARNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Product Dimensions All tolerances: ±1/16” (±1.6 mm) unless otherwise noted. Model HDCT304 Front of cooktop Power cord Gas inlet 2 1/8”...
Page 7
Installation Specifications Product Dimensions (Con’t) All tolerances: ±1/16” (±1.6 mm) unless otherwise noted. Model HDCT365 Front of cooktop Gas inlet Power cord in 2 1/4” (5.7 cm) 1” (2.5 cm) Chassis HDCT365 Power Cord and Gas Inlet Location Top panel overhang...
• This appliance is to be used in conjunction with a suitable vent • Allow at least 1/4” (6 mm) clearance between the bottom of the hood or an approved Dacor downdraft vent. chassis and all combustible surfaces, including the upper edge of a drawer inside the countertop cabinet below the cooktop.
Page 9
Installation Specifications Cutout Dimensions All tolerances ±1/16” (±1.6 mm) unless otherwise noted. Countertop Cutout View Rear wall Vertical combustible surface 4 1/4" (10.8 cm) min. from mounting surface to combustibles below cooktop chassis Min. distance to combustible side 1 7/8" min. wall above countertop (both sides) (4.8 cm) Countertop Cutout Dimensions...
If any parts are missing, see Replacement Parts List on Pg. 12 • Do not use Teflon tape or plumber’s putty on flexible gas line con- for Dacor Customer Assurance and ordering information. nections. • Before use, test the gas lines for leaks as instructed. Do not use a flame to check for leaks.
Installation Instructions Assembling the Burners WARNING • Never attempt to operate the cooktop with any of the burner parts removed. • Do not attempt to adjust the burner air mixture settings. All adjustments are preset at the factory. Remove the burner heads, burner rings, burner caps, and grates from their shipping packages. Place the caps on the burner assemblies as shown below to ensure proper function.
• Repeat the IGNITION TEST (Step 6). within the maximums in these instructions? (See Pg. 3.) □ • If the unit still does not work, contact Dacor Customer Was the cooktop secured with the provided hold-down Assurance: 833-35-ELITE (833-353-5483). Do not try to repair brackets? (See Pg.
Replacement Parts List Replacement Parts List Replacement parts can be obtained by contacting Grate Sizes Dacor Customer Service. Dacor Customer Assurance Phone: 833-35-ELITE (833-353-5483) USA, Canada) . to 5:00 . Pacific Time Mon – Fri 5:00 Cooktop Part HDCT304 HDCT365...
Page 14
Replacement Parts List Cooktop Parts Cooktop Layout Burner Location Left Rear Right Rear Center Rear Left Front Right Front Center Front...
Wiring Diagrams WIRING DIAGRAM WIRING DIAGRAM 120V, 60Hz. HDCT304 HPCT304G DYCT304G POWER SUPPLY CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION VERIFY PROPER OPERATION WHEN SERVICING CONTROLS. WIRING ERRORS CAN AFTER SERVICING CAUSE IMPROPER AND DANGEROUS OPERATION.
Page 16
Wiring Diagrams WIRING DIAGRAM WIRING DIAGRAM 120V, 60Hz. DYCT365G HPCT365G HDCT365 POWER SUPPLY CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION VERIFY PROPER OPERATION WHEN SERVICING CONTROLS. WIRING ERRORS CAN AFTER SERVICING CAUSE IMPROPER AND DANGEROUS OPERATION. ISOLATOR BOARD P/N 106104 IGNITOR, NO SWITCH LR BURNER...