Related Manuals for LEGRAND 5739 46
Summary of Contents for LEGRAND 5739 46
- Page 1 Keypad connector with display User manual 5739 46 5739 47 Part. U3289A - 11/08-01 PC...
-
Page 3: Table Of Contents
Contents Introduction Editing ■ The Keypad connector with display ■ The connector menu The keypad Accessing the settings menu ■ ■ ✔ Navigation keys Setting the date and hour ■ ■ The display ■ Adjusting the contrast ✔ Main screen ■... -
Page 5: Introduction
Introduction The Keypad connector with displa ■ The keypa ■ Navigation key ✔ The displa ■ Main scree ✔ In case of an alar ✔ Settings men ✔ What is the display showing ■... -
Page 6: The Keypad Connector With Display
1 - Introduction The keypad connector with display can be used to arm and disarm the ■ The Keypad connector with display burglar alarm system, to activate the various zones based on the current needs, or to activate one of the division scenarios programmed on the burglar alarm control unit. -
Page 7: The Keypad
1 - Introduction ■ The keypad ■ The display ✔ ✔ Navigation keys Main screen - Key for cancelling the System zones 1 2 3 4 selection and for returning to the previous page – if it is held down, you can escape from the ON/OFF indication programming menu Date and hour... -
Page 8: What Is The Display Showing
1 - Introduction ■ What is the display showing? System off , e.g.: zones 1, 2, 4 active System on, intrusion alarm signal 1 2 3 4 15/11/08 14:23 scenario 2 1 2 3 4 System on, e.g.: zone activation as System off , Unit battery dead or in scenario 2 damaged... - Page 9 1 - Introduction System off , Burglar-alarm 1 2 3 4 (antitheft) battery dead or damaged and technical alarm signal 1 2 3 4 System off , one or more sensors disabled (Important Unit functions are disabled; disable only if extremely necessary) 15/11/08 14:25...
- Page 10 1 - Introduction...
-
Page 11: Operation
Operation Accessing the functions with ✔ concealment enabled Enabling - disabling the burglar ■ alarm With user cod ✔ With transponder ke ✔ Activation scenario ■ Activating - deactivating the ■ zones With user cod ✔ With transponder ke ✔ Stopping the siren soun ■... -
Page 12: Accessing The Functions With Concealment Enabled
2 - Operation ■ Accessing the functions with concealment ■ Enabling - disabling the burglar alarm enabled ✔ With user code The Concealment function can be used to prevent displaying of the sy- When the burglar alarm (antitheft) is stem status to anyone without a user code or an enabled transponder. 1 2 3 4 disabled, an open lock appears in the middle of the display... -
Page 13: With Transponder Key 1
2 - Operation ■ Activation scenarios ✔ With transponder key It is possible to activate one of the zone division scenarios saved on the Burglar Alarm Control Unit When the burglar alarm (antitheft) is 1 2 3 4 1 2 3 4 disabled, an open lock appears in the middle of the display 15/11/08... -
Page 14: Activating - Deactivating The Zones
2 - Operation ■ Activating - deactivating the zones ✔ You can deactivate (reactivate) one or more zones at any time. This With user code will allow you to personalise the burglar-alarm operation according to your needs. The zones (max. 4) of the system are all 1 2 3 4 active (e.g. -
Page 15: With Transponder Key
2 - Operation ✔ With transponder key The zones (max 4) of the system are all 1 2 3 4 active (e.g. 1-2-3-4) 15/11/08 15:06 Press the corresponding key on the Unit keypad to deactivate zone 3 Confi rm the operation by bringing a transponder near the reader within 5 seconds The display shows zone 3 without the... -
Page 16: Stopping The Siren Sound 1
2 - Operation ■ Stopping the siren sound If the alarm goes on while you’re there, you can stop the siren as follows: ✔ ✔ With user code With transponder key Make sure there are no trespassers in Make sure there are no trespassers in 1 2 3 4 1 2 3 4 the house... -
Page 17: Activating The Robbery Alarm
2 - Operation ■ Activating the robbery alarm In case of robbery, it is possible to deactivate the burglar alarm system, while at the same time sending the emergency calls to the numbers saved in the Control Unit 1 2 3 4 15/11/08 15:09 Press... -
Page 18: What Type Of Alarm Occurred
2 - Operation ■ What type of alarm occurred? When an alarm signal is displayed, you can fi nd out what type it is (intru- In case of a technical alarm (its symbol appears), you can fi nd out which sion, technical, etc.) and which detector has detected it;... -
Page 19: Editing
Editing The connector men ■ Accessing the settings men ■ Setting the date and hou ■ Adjusting the contras ■ Disabling the buzze ■ Activating concealment mode ■... - Page 20 3 - Editing ■ The connector menu ■ Accessing the settings menu This procedure is necessary to access the settings menu: In this manual we felt it would be appropriate to explain all the custo- misation functions that may be useful when using the connector. These functions can be easily accessed without any risks of compromising the Ensure that the system is disarmed 1 2 3 4...
- Page 21 3 - Editing ■ Setting the date and hour In order for the system to constantly keep all memorised events under control, it is important to set the correct date and hour. The new Date and Hour settings will also be sent to the Control Unit. Access the settings menu Type in the current hour and date on 0 : 0 0...
- Page 22 3 - Editing ■ Adjusting the contrast This function can be used to adjust the contrast of the display screen for optimum view. Accessing the settings menu The display will show “in execution” for a few second, after which the previous Code/Key page is displayed in progress...
- Page 23 3 - Editing ■ Disabling the buzzer The operations performed using the connector (pressing the keys, arming the system etc.) are confi rmed acoustically by the built in buzzer. The following procedure can be used ot disable the buzzer. Go to the settings menu The display will show “in execution”...
-
Page 24: Activating Concealment Mode
3 - Editing ■ Activating concealment mode This function can be used to prevent displaying of the system status to anyone without a user code or an enabled transponder. Go to the settings menu The display will show “in execution” for a few second, after which the previous Code/Key page is displayed... - Page 25 Notes...
- Page 26 Notes...
- Page 28 Installer stamp World Headquarters and International Department 87045 LIMOGES CEDEX FRANCE : 33 5 55 06 87 87 Fax : 33 5 55 06 74 55 www.legrandelectric.com...
Need help?
Do you have a question about the 5739 46 and is the answer not in the manual?
Questions and answers