ABB RED615 Applications Manual page 57

1MRS758127 C
RED615
Application Manual
Set the parameters for SSCBR1 properly.
X120_BI3_CB_OPENED
X120_BI2_CB_CLOSED
CB_OPEN_COMMAND
CB_CLOSE_COMMAND
X110_BI3_GAS_PRESSURE_ALARM
CB_SPRING_DISCHARGED
X110_BI4_CB_SPRING_CHARGED
GUID-E16440E7-97F8-4BA5-A65A-8832F72F6333 V1 EN
Figure 29: Circuit breaker condition monitoring alarm
SSCBR1_TRV_T_OP_ALM
SSCBR1_TRV_T_CL_ALM
SSCBR1_SPR_CHR_ALM
SSCBR1_OPR_ALM
SSCBR1_OPR_LO
SSCBR1_IPOW_ALM
SSCBR1_IPOW_LO
SSCBR1_CB_LIFE_ALM
SSCBR1_MON_ALM
SSCBR1_PRES_ALM
SSCBR1_PRES_LO
GUID-CA85737C-AE1C-4BB1-B7AC-97A97EB90DAD V1 EN
Figure 30: Logic for circuit breaker monitoring alarm
X110_BI4_CB_SPRING_CHARGED
GUID-9B1B6395-2EAC-4927-9D9E-77EE41162FF6 V1 EN
Figure 31: Logic for start of circuit breaker spring charging
Two separate trip circuit supervision functions are included; TCSSCBR1 for power
output X100:PO3 and TCSSCBR2 for power output X100:PO4. The functions are
blocked by the master trip TRPPTRC1 and TRPPTRC2 and the circuit breaker open
signal.
It is assumed that there is no external resistor in the circuit breaker
tripping coil circuit connected in parallel with the circuit breaker
normally open auxiliary contact.
Set the parameters for TCSSCBR1 properly.
RED615 standard configurations
SSCBR1
BLOCK TRV_T_OP_ALM
POSOPEN TRV_T_CL_ALM
POSCLOSE SPR_CHR_ALM
OPEN_CB_EXE
CLOSE_CB_EXE
PRES_ALM_IN
PRES_LO_IN
SPR_CHR_ST CB_LIFE_ALM
SPR_CHR
RST_IPOW
RST_CB_WEAR
RST_TRV_T
RST_SPR_T INVALIDPOS
OR6
B1 O
B2
B3
B4
B5
B6
B1
B2
OR6
B1 O
B2
B3
B4
B5
B6
NOT
IN
Section 3
SSCBR1_TRV_T_OP_ALM
SSCBR1_TRV_T_CL_ALM
SSCBR1_SPR_CHR_ALM
OPR_ALM
SSCBR1_OPR_ALM
OPR_LO
SSCBR1_OPR_LO
IPOW_ALM
SSCBR1_IPOW_ALM
IPOW_LO
SSCBR1_IPOW_LO
SSCBR1_CB_LIFE_ALM
MON_ALM
SSCBR1_MON_ALM
PRES_ALM
SSCBR1_PRES_ALM
PRES_LO
SSCBR1_PRES_LO
OPENPOS
CLOSEPOS
OR
O
SSCBR1_ALARMS
OUT
CB_SPRING_DISCHARGED
51