Diagnosis; Diagnostic Display - Siemens SIPART PS2 6DR5020 Series Manual

Operation
4.5

Diagnosis

4.5.1 Diagnostic display

No. Abbrevia- Meaning
tion
1 STRKS Number of strokes (Strokes)
2 CHDIR Changes of direction (Changes of Direction)
3 Fault counter (Counter )
CNT
4 A1CNT Alarm counter 1 (Alarm 1 Counter)
5 A2CNT Alarm counter 2 (Alarm 2 Counter)
6 HOURS Operating hours (Hours)
7 WAY Determined actuating path (Way)
8 TUP Travel time up (Travel Time Up)
9 TDOWN Travel time down (Travel Time Down)
10 LEAK Leakage (Leakage)
11 P0 Potentiometer value below stop (0%)
12 P100 Potentiometer value bottom stop (100%)
13 IMPUP Impulse length up (Impulse Length Up)
14 IMPDN Impulse length down (Impulse Length Down)
15 DBUP Dead zone up (Dead Band Up)
16 DBDN Dead zone down (Dead Band Down)
17 SSUP Short step zone up (Short Step Zone Up)
18 SSDN Short step zone down (Short Step Zone Down)
19 TEMP Current temperature
20 TMIN Minimum temperature ("drag pointer")
21 TMAX Maximum temperature ("drag pointer")
22 T1 Number of operating hours in Temperature range 1
23 T2 Number of operating hours in Temperature range 2
24 T3 Number of operating hours in Temperature range 3
25 T4 Number of operating hours in Temperature range 4
26 T5 Number of operating hours in Temperature range 5
27 T6 Number of operating hours in Temperature range 6
90
You go to the diagnostic display from automatic or manual operation by
simultaneously pressing all three keys for at least two seconds.
Table 3-1, page 91 shows an overview of the displayable values. In the
third column the corresponding English term from which the abbrevia-
tion is derived is shown next to the German meaning unless this is self
explanatory.
The diagnostic display has a similar structure to in the "Configuration"
operating mode. the top line shows the value of the diagnostic variable,
the bottom line the number and abbreviation of the displayed variable.
The respective next diagnostic value can be selected with the operation
mode key . By pressing and holding the operation mode key and
additionally pressing the decrement key
stic values in reverse order.
Certain values can be set to zero by pressing the increment key
at least 5 seconds. This is noted in the last column in the table.
Some diagnostic values may be greater than 99999. In this case the
display switches to exponential display. Example: the value 1234567 is
displayed as 1.23E6.
you can select the diagno-
Displayable Unit
values
0 to 4.29E9 - -
0 to 4.29E9 - -
0 to 4.29E9 - -
0 to 4.29E9 - -
0 to 4.29E9
0 to 4.29E9 Hours
0 to 130 mm or _
0 to 1000 s
0 to 1000 s
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
2 to 100 ms
2 to 100 ms
0.1 to 100.0 %
0.1 to 100.0 %
0.1 to 100.0 %
0.1 to 100.0 %
- -40 to 85
_C
- -40 to 85
_C
- -40 to 85
_C
0 to 4.29E9 Hours
0 to 4.29E9 Hours
0 to 4.29E9 Hours
0 to 4.29E9 Hours
0 to 4.29E9 Hours
0 to 4.29E9 Hours
SIPART PS2 Manual
A5E00074631-01
for
Rest
poss.
x
x
x
x