Siemens SIPART PS2 6DR5020 Series Manual page 103

Option modules
Electrical data
Explosion protection to
EN 50 014 and EN 50 020
Mounting location
Permissible ambient
temperature for operation
Alarm module
Binary alarm outputs A1, A2
and alarm output
Signal status High
(not triggered)
3
Signal status Low )
(triggered)
Internal capacitance C
i
Internal inductance L
i
Power supply U
H
Connection to intrinsically-safe
switching amplifier to DIN 19 234
Binary input BI2
• Electrically connected to
basic device
- Signal status 0
- Signal status 1
- Contact rating
• Electrically isolated from
basic device
- Signal status 0
- Signal status 1
- Input resistance
Static destruction limit
Internal inductance and capacit.
Connection to intrinsically-safe
voltage source
Electrical isolation
I module
y
Direct current output for
position feedback
Rated signal range i
Operating range
Power supply U
H
[k Ω ]
External load R
B
Transmission error
Temperature influence
Resolution
Residual ripple
Internal capacitance C
i
Internal inductance L
i
For connection to intrinsically-
safe sources with
• U
i
• I
i
• P
i
SIPART PS2 Manual
A5E00074631-01
Without Ex pro- With Ex protection
tection
– II2G EEx ia/ib II C
1
T4/T5/T6 )
– Zone 1
-30 to +80 °C T4: -30 to +80 °C
T5: -30 to +65 °C
T6: -30 to +50 °C
6DR4004-8A 6DR4004-6A
(without Ex pro- (with Ex protec-
tection) tion)
≥ 2.1 mA 2
Conductive )
R = 1 k Ω ,
+3/-1 %
≤ 1.2 mA 2
Non-conductive )
I < 60 µA
R
≤ 5.2 nF
–
– Negligible
≤ 35 V
–
≤ 15.5 V DC
– U
o
≤ 25 mA
I
k
P ≤ 64 mW
Floating contact, open
Floating contact, closed
3 V, 5 µ A
≤ 4.5 V or open
≥ 13 V
≥ 25 k Ω
± 35 V –
– Negligible
≤ 25.2 V
– U
i
The 3 outputs, the input BI2 and the
basic device are electrically isolated
from each other
6DR4004-8J 6DR4004-6J
(w/o Ex protection) (with Ex protec-
tion, only for temp.
class T1 to T4)
Two-wire system
4 to 20 mA, short-circuit-proof
3.6 to 20.5 mA
+12 to 35 V +12 to 30 V
≤ (U
[V] - 12 V) /i [mA]
H
≤ 0.3 %
≤ 0.1 %/10 K
≤ 0.1 %
≤ 1 %
≤ 11 nF
–
– Negligible
for T4
≤ 30 V
–
≤ 100 mA
–
≤ 1 W
–
SIA module
Limit monitor with slot-type initia-
tors and alarm output
Connection
2 slot-type initiators
Function
Connection to intrinsically-safe
switching amplifier, DIN 19 234
Ex protection
EMC
1
) Only in conjunction with the basic device 6DR5
2
) Switching thresholds with supply to DIN 19 234: U
3
) Low is also the state if the basic device is faulty or without an
electrical power supply.
Technical data
6DR4004-8G or
6DR4004-6G (only for 6DR5...)
Two-wire system to DIN 19 234
(NAMUR), for series-connected
switching amplifiers
Type SJ2-SN
NC
EEx ia/ib IIC T4/T5/T6
See alarm module
7 7 7 - 7 E 7 7 7
= 1 k Ω.
= 8.2 V, R
H i
103
.