Advertisement
APPLICATION GUIDELINES FOR THE 6162RF
Table 1 – Application Guidelines
If...
And...
This is the only
You want to use both
transceiver on
the receiver and
the system,
transmitter function
on a single-partition
system,
There is another
You want to use only
receiver or
the transmitter
transceiver on
function on a second
the system,
partition,
You want to use only
the transmitter
function on a single-
partition system,
Notes:
* On VISTA-40 panels and above, wireless keypads (e.g., 5828) can only be used on a single partition. This partition is programmed in field 1*48,
and must match the partition assigned to the 6162RF. Wireless keys can be used on more than one partition, using a House ID programmed in the
6162RF and the devices. In this case, the wireless keys must be assigned to the same partition as the 6162RF.
** On VISTA-20P panels, the 6162RF will use the House ID programmed in the panel for the partition to which it is assigned. Wireless keypads can
only be used on Partition 1.
4. PROGRAM
Refer to the following procedure to program the 6162RF:
Table 2 – 6162RF Programming
STEP
1.
Enter Programming Mode: Within 60 seconds of power up, press and hold down the
same time for 3 seconds.
Notes:
• If unable to enter program mode, reboot the keypad and try again after the keypad LEDs stop flashing (refer to Settings Key
Functions Table on page 1).
• The keypad will not enter address mode if the control panel to which it is connected is in programming mode.
• If 30 seconds passes with no key entry, the keypad automatically exits address mode. Reboot the keypad and enter address mode again.
Keypad Address. The keypad address appears (Default = 16). Enter a
2.
two-digit keypad address. Press the
Note:
Refer to the control panel's installation instructions for acceptable keypad
addresses.
3.
Receiver Enable. Enter [1] to enable, or [0] to disable the receiver. Press
to continue.
4.
Receiver Address. If the receiver is enabled, enter the two-digit receiver
address. (00-30).
Note:
Refer to the control panel's installation instructions for the acceptable
receiver addresses.
Press
to continue.
User Code. Enter a valid four-digit user code to enable Single Button
5.
Arming keys. The user code must be programmed in the control.
Press
to continue.
6.
House ID. This prompt will only appear if the receiver is disabled. If the
receiver is enabled the 6162RF will use the House ID programmed in the
panel. Refer to Application Guidelines section when selecting a House ID.
To program a House ID: Enter 01-31; To disable the transmitter: Enter 00
Note: Each device that will receive status from the 6162RF must be set to the same
House ID as the 6162RF (refer to Application Guidelines section).
Then...
•
Set the keypad to a device address assigned to the desired partition.*
•
Enable the receiver.
•
Program a system House ID in the control panel (this will enable the transmitter
function).**
•
Set the wireless devices that will communicate with this 6162RF to the same
system House ID.
•
Set the keypad to a device address assigned to the desired partition.*
• Disable the receiver.
• Program a DIFFERENT House ID in the 6162RF than is programmed in the
control panel.*/ **
•
Set the wireless devices that will communicate with this 6162RF to the same
House ID as the 6162RF.
•
Set the keypad to a device address assigned to the Partition 1.
• Disable the receiver.
• Program a House ID in the 6162RF that matches the system House ID
programmed in the control panel.*
•
Set the wireless devices that will communicate with this 6162RF to the same
House ID.
DESCRIPTION
key to continue.
- 2 -
DISPLAY
and
keys at the
CON ADDR = 16
RECEIVER
ON [0= OFF]
REC ADDR = 00
USER CODE : ****
HOUSE ID = XX
CHOICES
00-31
1 = ON
0 = OFF
00-30
0000-9999
01-31
00 = Disable
Transmitter
Advertisement
