Advertisement
Table 2 – 6162RF Programming (continued)
STEP
6.
Press
to continue.
(cont.)
7.
Enable High Security Mode. Enter [1] to select High Security Mode.
Note: If the High Security mode is enabled, the 6162RF will only recognize
encrypted devices. If the High Security mode is disabled, the 6162RF will
process commands from both encrypted and non-encrypted devices.
Press
to continue.
8.
Disable High Security Devices. Press the
and exit Program Mode.
ACTIVATING HIGH SECURITY DEVICES
The procedure below should be followed when using High-Security (encrypted) devices.
Table 3 – Activating High Security Devices
STEP
1.
Follow the normal procedure for programming the device into the control panel (refer to the Installation Instructions for the
device that you are programming). Exit out of Programming Mode.
2.
Put the control panel in Go / No Go Test mode. (See the Installation Guide for the panel being installed.)
3.
Follow the instructions supplied with each wireless device to enroll the device in High-security mode. After each device is
enrolled, the 6162RF will momentarily display "SECURE DEVICE" along with the device number and its serial number.
Note: The 6162RF will support a maximum of 8 devices. If you attempt to enroll additional devices the keypad will display
"EXCEEDED NUMBER" "ALLOWED DEVICES".
CHANGING USER CODE AND DISABLING HIGH SECURITY DEVICES
This mode gives you the ability to change the user code used to enable the single button arming keys and disable high security on
all wireless keys that have been enrolled in the 6162RF. The disable high security devices option is particularly useful if a user loses
a wireless key.
Once high-security (encrypted) devices have been disabled, they will only operate if the 6162RF is set to listen to both
encrypted and non-encrypted devices (programming step 6 in Table 2). To completely disable the devices, they must be
deleted from the control panel.
Table 4 – Disabling High Security Devices
STEP
1.
After the keypad has been powered for at least 60 seconds, press and hold
down the
keypad address will be displayed. (You cannot change the keypad's address
at this point.) Press
2.
User Code. At the User Code prompt, enter the valid 4-digit user code that
will be used to enable the single button arming keys. Press
continue.
3.
Delete High Security Devices. Enter [1] to remove all high-security
(encrypted) devices. Press
4.
If YES was selected in Step 2 the unit will display a confirm request to delete
the stored high security device. Enter [1] to accept and press
the programming mode.
OPTIONAL MENU MODE PROGRAMMING FEATURE*
The Menu Mode Programming allows easy data entry and system
programming for a basic installation. Refer to the Menu Mode Programming
Supplement for details.
*Menu Mode Programming is available only with certain controls. See the Control panel
instructions for details.
To Enter Menu Mode Programming: First enter the normal Control
programming mode [Installer Code + 800], then press and hold
seconds. Wait for the 'Communicating...' screen to disappear, then use the
data entry and navigation keys to move through the programming screens.
See the control panel Programming instructions for complete details.
DESCRIPTION
DESCRIPTION
and
keys at the same time for 3 seconds. The current
to continue.
to continue.
key to skip this prompt
DESCRIPTION
to
to exit
Navigation and Data Entry Keys
Clear Data Entry
for 2
Toggle entries
- 3 -
DISPLAY
HIGH SECURITY
OFF [1 = ON]
DISABLE HS DEV?
NO [1 = YES]
DISPLAY
CON ADDRESS=XX
USER CODE : ****
DELETE DEVICES?
NO [1 = YES]
ARE YOU SURE?
NO [1 = YES]
Enter / Exit Quick
Programming
AWAY
STAY
Next
Yes
field
CHOICES
1 = ON
(Enable)
0 = OFF
(Disable)
1 = YES
0 = NO
CHOICES
Programmed
Keypad
address
appears
0000-9999
1 = YES
0 = NO
1 = YES
0 = NO
Next
Page
No
Previous
field
Advertisement
