Download  Print this page

Honeywell 6150 - Ademco Fixed - Display Keypad Installation And Setup Manual

Setup guide.
Hide thumbs
   

Advertisement

Keypad Features
Backlit Display
Dedicated Function Keys
Built-in Sounder
Note: Permanent display backlighting is an option on some controls (see the control's instructions for details).
GENERAL INFORMATION
The ADEMCO 6150 and ADEMCO 6160 are addressable
Remote Keypads designed for use with ADEMCO control
panels. Addresses are set via the keypad keys.
The keys on the keypads are continuously backlit for
convenience.
Supervised by control panel (if supported).
KEYPAD DISPLAYS AND LEDS
The keypads have the following display features:
Fixed
2-line
Model
Word
Alpha
Display
Display
6150
X
6160
X
The following table shows the LEDs and their functions:
LED
Red
Lights when the system is armed in any mode
Green
Lights when the system is "ready" to be armed.
SPECIAL FUNCTION KEYS
The keypads also feature function keys. These keys may be
programmed for panic alarms or other special functions
such as macros. See the control's instructions for details.
Function keys must be held down for at least 2
seconds to activate an alarm; key pairs are activated
immediately.
Function Keys
A or [1] and [✻]
B or [✻] and [#]
C or [3] and [#]
D
INSTALLATION AND SETUP GUIDE
2-digit
Custom
Zone
Zone
Identifier
Descriptors
X
X
Function
ADEMCO 6150
Fixed-Word
(see note)
Piezo
WIRING AND INSTALLATION
The keypads can be surface mounted directly to a drywall,
or to a single- or double-gang electrical box.
1. Push the two case release snaps at the bottom of the
keypad with the blade of a medium screwdriver (this will
push in the release snap), then pull that side of the case
back away. Insert the screwdriver in the side of the
keypad (between the front and back case) and gently
twist to release the side locking tab. Repeat for the other
side. Refer to Figure 1 for location of the case back
release snaps and locking tabs.
2. Route wiring from the control panel through the opening
in the case back.
3. Mount the case back to a wall or electrical box.
4. Wire directly from the keypad's terminal block to the
terminal block on the control panel. (See Wiring Table
below).
NOTE: No more than one wire per terminal may be
connected. If daisy-chained configuration is required,
pig-tail wires together so that only one wire is
terminated under the screw. Use 16-24 AWG wire only!
Wiring Table (All Keypads)
Keypad
G
+
Y
See the control panel's Installation and Setup Guide for
more complete details.
5. Reattach the keypad to its case back.
K3590-ADV4 2/09 Rev. A
ADEMCO 6150 & 6160
REMOTE KEYPADS
ADEMCO 6160
2-Line Alpha
(see note)
Speaker
Control Panel
Data In
– Aux Pwr (GND)
+ Aux. Pwr
Data Out
Wire Color
Green
Black
Red
Yellow

Advertisement

   Related Manuals for Honeywell 6150 - Ademco Fixed - Display Keypad

   Summary of Contents for Honeywell 6150 - Ademco Fixed - Display Keypad

  • Page 1 K3590-ADV4 2/09 Rev. A ADEMCO 6150 & 6160 REMOTE KEYPADS INSTALLATION AND SETUP GUIDE ADEMCO 6150 ADEMCO 6160 Keypad Features Fixed-Word 2-Line Alpha Backlit Display (see note) (see note) Dedicated Function Keys Built-in Sounder Piezo Speaker Note: Permanent display backlighting is an option on some controls (see the control's instructions for details). GENERAL INFORMATION WIRING AND INSTALLATION The ADEMCO 6150 and ADEMCO 6160 are addressable...
  • Page 2 INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM. For the latest warranty information, please go to: http://www.security.honeywell.com/hsc/resources/wa/index.html K3590-ADV4_Š 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 K3590-ADV4 2/09 Rev. A Copyright © 2009 Honeywell International Inc. www.honeywell.com/security...

This manual also for:

6160 - deluxe 32-character alpha keypadAdemco 6160

Comments to this Manuals

Symbols: 0
Latest comments: