Download  Print this page

Honeywell ADEMCO 6150 Installation And Setup Manual

Remote keypads.
Hide thumbs
Most useful pages: More
   

Advertisement

Keypad Features
Backlit Display
Dedicated Function Keys
Built-in Sounder
Note: Permanent display backlighting is an option on some controls (see the control's instructions for details).
GENERAL INFORMATION
The ADEMCO 6150 and ADEMCO 6160 are addressable
Remote Keypads designed for use with ADEMCO control
panels. Addresses are set via the keypad keys.
The keys on the keypads are continuously backlit for
convenience.
KEYPAD DISPLAYS AND LEDS
The keypads have the following display features:
Fixed
2-line
Model
Word
Alpha
Display
Display
6150
X
6160
The following table shows the LEDs and their functions:
LED
Function
Red
Lights when the system is armed in any mode
Green
Lights when the system is "ready" to be armed.
SPECIAL FUNCTION KEYS
The keypads also feature function keys. These keys may be
programmed for panic alarms or other special functions such
as macros. See the control's instructions for details.
Function keys must be held down for at
least 2 seconds to activate an alarm, key
pairs activate immediately.
Function Keys
A or [1] and [
B or [
C or [3] and [#]
INSTALLATION AND SETUP GUIDE
Custom
2-digit Zone
Identifier
Descriptors
X
X
]
] and [#]
D
ADEMCO 6150
Fixed-Word
YES (see note)
YES
Piezo
WIRING AND INSTALLATION
The keypads can be surface mounted directly to a drywall, or to
a single- or double-gang electrical box.
1.
Remove the case back by pushing down two "snaps."
See diagram below.
2.
Route wiring from the control panel through the
opening in the case back.
3.
Mount the case back to a wall or electrical box.
4.
Wire directly from the keypad's terminal block to the
terminal block on the control board as follows:
Zone
Keypad
G
X
+
Y
See the control panel's Installation and Setup Guide for
more complete details.
5.
Reattach the keypad to its case back.
ARMED
READY
NOTE:
TO REMOVE CASE BACK
PUSH IN THE TWO MOUNTING
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT UP.
ADEMCO 6150 & 6160
REMOTE KEYPADS
ADEMCO 6160
2-Line Alpha
YES (see note)
YES
Speaker
Wiring Table (All Keypads)
Control Panel
Data In
– Aux Pwr (GND)
+ Aux. Pwr
Data Out
RETAINING
SNAPS
K3590-ADV2 4/04 Rev. A
Wire Color
Green
Black
Red
Yellow

Advertisement

Table of Contents

   Related Manuals for Honeywell ADEMCO 6150

   Summary of Contents for Honeywell ADEMCO 6150

  • Page 1 Note: Permanent display backlighting is an option on some controls (see the control's instructions for details). GENERAL INFORMATION WIRING AND INSTALLATION The ADEMCO 6150 and ADEMCO 6160 are addressable The keypads can be surface mounted directly to a drywall, or to Remote Keypads designed for use with ADEMCO control a single- or double-gang electrical box.
  • Page 2 REFER TO INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM. 165 Eileen Way, Syosset, New York 11791 Copyright © 2004 Honeywell International Inc. www.honeywell.com/security ÊK3590-ADV2KŠ K3590-ADV2 4/04 Rev. A...

This manual is also suitable for:

Ademco 6160

Comments to this Manuals

Symbols: 0
Latest comments:
  • jim mcginnis Feb 18, 2016 05:53:
    how do I know when keypad is powered up?