Subscribe to Our Youtube Channel
Related Manuals for TOPP K200T
Summary of Contents for TOPP K200T
- Page 1 INSTRUCTIONS FOR INSTALLATION AND USE ELECTROMECHANICAL AUTOMATION FOR SLIDING K200T LINEAR TELESCOPIC DOORS WITH TWO OR FOUR WINGS K280T installer's manual/original instructions COD.0P5521 VER 0.0 REV 08.19...
-
Page 2: Table Of Contents
6.2- Spare parts and accessories available on request ................pag. 58 6.3- Demolition............................pag. 59 6.4- Troubleshooting ..........................pag. 59 7- EC DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY ......pag. 60 EU DECLARATION OF CONFORMITY ......................pag. 60 K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 3: 1- General Information
& TOPP srl reserves the right to amend or improve the manual and the products described therein at any time without notice. & The data contained in this manual were written and checked with the maximum care; TOPP srl is not liable for possible errors due to omissions or printing errors, or errors in transcription. -
Page 4: User
It should be applied by the installation technician in a clearly visible position on the outside of the automation unit. PROPER USE The K200T/280T automation mechanism was designed and produced exclusively to operate (open and close) linear sliding doors in residential, public and industrial buildings. -
Page 5: Technical Data
The quantity of some parts may vary depending on the type of configuration used (e.g. number of wings). If you need more parts, contact the manufacturer. Ref. Warning labels for moving wings K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 6: Models
F = side fixed thickness profile VL = gross opening VPA = net doorway width PC = electric wire raceway LT/LC BP = rail + runner on the floor LT/LC =automation length / casing length K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 7: Types Of Sliding Doors With Two Wings
Sliding door panel Automation Fig. 5b Fixed door panel Wall end Sliding door panel Automation Tubular jamb Fig. Fixed door panel Wall end Sliding door panel Tubular jamb Sliding door panel Overlap Automation K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 8: Description Of Parts And Dimensions
Fast wing Anta Veloce Main crossbar 13 - Photocell control unit Carriage with double wheel 14 - Gearmotor K200T Lateral case fastener Rail for door guide 15 - Adapter for door panel suspension 16 - Fast wing plastic runner Casing... - Page 9 Belt transmission front bracket (RCA) with tension adjustment device 10 - Electronic control circuit 22 - Slow wing plastic runner with thickness 11 - 23 - Logline Door lock with manual release 12 - Emergency battery 24 - Ferrite K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 10 Fig. Fig. K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
-
Page 11: General Recommendations
& Before installing the automation, verify that the structure to be automated is stable, sturdy and able to withstand the weight of the automation and, if necessary, take steps to ensure that it is. Topp srl is not liable for failure to comply with the rules of good workmanship in the construction of the door panels to motorize, or for any distortions that may develop with use of the device. -
Page 12: Assembling The Adaptor And Track
Drill the door panel at the top and fasten the adapter using cylindrical M6 screws or cylindrical self-tapping d5.5 screws depending on the type of material; Drill the door at the bottom and fasten the rail using flared self-tapping cylindrical screws diam. 4.8. Fig. 10 Adapter rail Adapter Door panel Rail Flaring K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 13: Assembling Trolleys On Wings
Standard adapter Fig. 12 2 doors panel, opening toward the left Slower wing back 65÷70 Fast wing front Fig. 13 2 doors panel, opening toward the right Slower wing back 65÷70 Fast wing front K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... - Page 14 3100 2044 3200 2096 3300 2144 3400 2192 3500 2244 3600 2296 3700 2344 3800 1000 1000 2392 3900 1025 1025 2344 4000 1050 1050 2496 4100 1075 1075 2544 4200 1100 1100 2592 K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
-
Page 15: Adjustment Of Trolleys And Assembly Of Belt On Slow Wing
Slow wing back Wrench supplied side Note the direction of installation Belt joint plate Fig. 16 Slow wing,opening toward the right Internal Internal Slow wing back Wrench supplied side side Belt joint plate K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 16: Assembly And Adjustment Of Fast And Slow Sliding Wings
Use the height adjustment screws on the trolleys to raise or lower the wing by ±10mm (with the crossbar correctly installed in respect of the measurements and dimensions shown in Fig.8). Slow wing Fast wing Fig. 17 Bearing wheels Antiderailment wheel Trolley Trolley screw Fig. 19 Adjustment screw Fig. 18 K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... - Page 17 Fig. 20 Trolley bottom bracket Adapter Fast wing Slow wing Slow wing runner Fast wing runner Fig. 21 Fast wing Fast wing Slow wing Slow wing K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
-
Page 18: Assembling Drive Bracket And Belt Block Bracket On Slow Wing
-Stack and align the slow wing with the fast wing in the open position, fasten the FCT bracket (crossbar belt block) on the crossbar with the specific M5x12 screws (Fig. 27). It permits adjustment by ± 20mm. NOTE: Insert the threaded plate on the crossbar. K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... - Page 19 2 wings,opening toward the right Side fixing trolleys Drive bracket slow wing Slow wing M6x10 Rear trolley fast wing Fast wing M5x8 Fig. 27 25 (+/-20) Belt block bracket DETAIL A N° 2 screws M5x12 Threaded plate K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
-
Page 20: Assembling Motor Module, Belt Transmission,Belt On Fast Wings And Logline
ASSEMBLING MOTOR MODULE, BELT TRANSMISSION,BELT IN FAST WINGS AND LOGLINE Fig. 28b Fig. 28a K200T - 2 WINGS (Fig.28a) L Belt L Logline 120 1162 1x2312 1000 120 1266 1x2520 1100 120 1370 1x2728 1200 120 1474 1x2936 1300 120 1578 1x3144... - Page 21 3600 2228 2228 2x4440 3611 3700 2280 2280 2x4544 3715 3800 2332 2332 2x4648 3819 3900 2384 2384 2x4752 3923 4000 2436 2436 2x4856 4027 4100 2488 2488 2x4960 4131 4200 2540 2540 2x5064 4235 K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 22 -Tighten screws “VTF” after checking that the transmission is aligned with the crossbar. Fig. 32a MOTOR MODULE BELT TRASMISSION EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
-
Page 23: Fastening Drive Brackets On Fast Wings
FASTENING DRIVE BRACKETS ON FAST WINGS 4 wings, simultaneous opening toward the right and left Fig. 33 K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... - Page 24 Horizontal adjustment slot Down belt bracket Wing drive bracket Fig. 35 2 WINGS LEFT - opening on the left Screws M6x8 Screws M6x10 Front trolley wing Horizontal adjustment slot Top belt bracket Wing drive bracket K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
-
Page 25: Assembling Wing Block
Attention!: The door block system is not to be considered as a device for protection against break-ins. K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 26: Assembling Casing Cover
Fig.41 Ref.4 Fasten the casing to the beam using the two screws type TCEI M5x10. Fig. 41 antivibration felt Rating place and “CE” marking M3,5x9,5 screws for fastening casing M5x10 screws for fastening casing K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 27: Assembling Raceway Fastening Brackets For Closure Of The Slow Wing
Fig. 43 Trolleys for profiles up to Trolleys for 35mm profiles up to 25mm Casing in sheet metal for Casing in sheet metal for profiles up to 35 mm profiles up to 25 mm K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 28: 4- Electrical Connection
Make sure that all the cables are inside the duct and that they cannot come into contact with moving parts once positioned. During installation, make sure that the conductor cables are secured by an additional attachment near the terminals or electrical connections, i.e. using bands. Make sure that the cables are stripped near the terminals. K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 29: Electronic Control Unit
7. Transformer input 8. Emergency battery system 13 11 14 9. Door block 2 input (pharmacy) 10. Door block 1 input 11. Lighted display K200T K280T 12. Gearmotor input 13. DOWN key Dip-Switch 1=off Dip-Switch 1=off 14. ENTER key Dip-Switch 2=off... -
Page 30: Pre-Wired Electrical Connections
PRE-WIRED ELECTRIC CONNECTIONS Fig. 45 K200T Automation Black Transformer Transformer Circuit Blue SMOKE TEST+ 17. INTERNAL 25. RESET (NEAR) FIRE SYSTEM 10. TEST+ SECURITY 26. OPEN EMERGENCY 11. GND 18. INTERNAL 27. PARTIAL CLOSURE 12. ANTIPANIC RADAR 28. EXIT ONLY DEVICE 19. - Page 31 14. LATERAL SECURITY 32. 24V SAFETY 1 22. EXTERNAL CURTAINS 15. GND RADAR 16. 24V 23. GND 24V* 24. 24V Ÿ Ÿ SIGNAL A Ÿ GND (shield) Ÿ SIGNAL B Ÿ * Unregolated K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
-
Page 32: Electrical Wiring Diagram (Flow Chart)
ELECTRICAL WIRING DIAGRAM (FLOW CHART) Fig. 47 50°C -20°C EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 33: Connection Of Detection Sensors
NO ATT. white white COM. ATT. grey grey grey grey +24V green/black green/black N.C. SIC white/black white/black COM. SIC yellow yellow NO ATT. COM. ATT. white white grey grey grey grey +24V K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... - Page 34 RX1 - TX1 = First beam RX2 - TX2 = Second beam ACTIV ATION yellow yellow N.O. white white grey grey grey grey +24V ACTIV ATION yellow yellow N.O. white white grey grey grey +24V grey EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 35 RX2 - TX2 = Second beam yellow yellow N.O. ACT. white white grey grey grey grey +24V green/black green/black N.C. SIC. white/black white/black yellow yellow N.O. ACT. white white grey grey grey grey +24V K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 36 +24V yellow yellow N.O. ACT. white white grey grey grey grey +24V green/black green/black N.C. SIC. white/black white/black yellow yellow N.O. ACT. white white grey grey grey grey +24V EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 37 Fig. ¬Digital program switch menu: PARAMETERS>OTHER PARAMETERS> SAFETY SENSOR LOGIC: N.C. WITHOUT TEST program parameter 9 with the dot IS2 EXTERNAL ACTIVATION/SAFETY IS2 INTERNAL ACTIVATION/SAFETY SENSOR SENSOR IS5 LATERAL SENSOR N.C. N.C. K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 38 RX1 - TX1 = First beam Rx2 - TX2 = Second Beam ACTIV ATION yellow yellow N.O. white white grey grey grey grey +24V N.C. ACTIV ATION yellow yellow N.O. white white grey grey grey grey +24V EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 39 NO ACT. white white COM. ACT. grey grey grey grey +24V green/black green/black N.C. SIC white/black white/black COM. SIC yellow yellow NO ACT. white white COM. ACT. grey grey grey grey +24V N.C. N.C. K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 40 N.C. N.C. N.O. yellow yellow ACT. white white grey grey grey grey +24V green/black green/black N.C. SIC. wite/black wite/black yellow yellow N.O. ATT. white white grey grey grey grey +24V EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 41 RX1 - TX1 = First beam Rx2 - TX2 = Second beam ACTIV ATION yellow yellow N.O. white white N.C. grey grey grey grey +24V ACTIV ATION N.C. yellow yellow N.O. white white grey grey grey grey +24V K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 42 ACTIVATION green green N.O. white white brown brown +24V black black TST- TEST TST+ N.C. rose rose SECURITY blue blue yellow yellow ACTIVATION green green N.O. white white brown brown +24V EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 43 ACTIVATION white white N.O. black black +24V braun braun TST- TEST grey grey TST+ N.C. yellow yellow SECURITY blue blue green green ACTIVATION white white N.O. black black +24V K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 44 +24V brown brown TST- black black TEST TST+ N.C. rose rose SECURITY blue blue yellow yellow ACTIVATION green green N.O. white white brown brown +24V 16 15 13 11 10 IS5 LATERAL S. EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 45 +24V TST- braun braun TEST grey grey TST+ N.C. yellow yellow SECURITY blue blue green green ACTIVATION white white N.O. black black +24V 16 15 13 11 10 IS5 LATERAL S. K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 46 OTHER PARAMETERS> SAFETY SENSOR LOGIC: N.C. WITH TEST Or program parameter 9 without the dot ELECTRICAL WIRING DIAGRAM FOR OPTEX USING ACTIVATION/SAFETY SENSOR MONITORED IS5 LA TERAL S. 1 IS5 LA TERAL S. 2 EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 47 OTHER PARAMETERS> SAFETY SENSOR LOGIC: N.C. WITH TEST Or program parameter 9 without the dot ELECTRICAL WIRING DIAGRAM FOR HOTRON USING ACTIVATION/SAFETY SENSOR MONITORED IS5 LA TERAL S. 1 Is5 LATERAL S. 2 K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
-
Page 48: Program Selection With Ms1 Knob
Cable ‘shielding’ should only be used for cable lengths in excess of 20 meters. For shorter cables cut the wire at the level of the sheath 1 2 3 4 5 DS2 DIGITAL SELECTOR CIRCUIT EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 49: Connection Of Key Device
Digital program switch menu: ¬ PARAMETERS> OTHER PARAMETERS> SAFETY SENSOR LOGIC:N.C. WITH TEST Or program parameter 9 without the dot 11 12 RX1 - TX1 = First Beam K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 50: Connetion Of Door Block And Pharmacy Function
Or program parameter 9 with the dot 11 12 RX1 - TX1 = First Beam 4.11 CONNETION OF DOOR BLOCK AND PHARMACY FUNCTION Door block with Door block with manual release manual release incorporated 1 incorporated 2 pharmacy function EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 51: 5- Use And Operation
“default battery operation mode”: the “continuous operation mode” and will continue to operate as set as in the selector program. The "battery operation mode" can be changed in other modes, using the Topp DS2 digital program switch. Emergency opening or closing can be set. In the case has been selected a different mode operation than the standard one, the automation will resume to function as the program set by the selector after restoring the 230V mains. -
Page 52: Reset Phase: Learning
MS1, automation will not perform any reset (near) as long as this mode will not be changed or if the request will be 'opening to boost key or emergency opening / fire. Once changed how automation will perform the reset (near) as shown above. EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 53: Programming Parameters
1. Press the “DOWN” key and hold for 5 seconds. The sequence of characters “Radio” appears on the 7-segment display. 2. If you have the Topp remote control TS2 press the smooth side of the first key (open function). If the Topp TS1 4-channel remote control is available, press the second key (Close Function). -
Page 54: List Of Errors And Warning
Antipanic sensor malfunction. Obstacle not removed. Check for obstacles or friction. Motor poles inverted. Reverse the cables. Doors free. Bus voltage low. Bus voltage high. Motor bridge voltage high. Causes the door block. EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 55: Self Restore Management Of Errors C-D-E-K-N-P-Q
During the slow opening in the preceding paragraph, the occupation of the side sensors causes a slow reclosing Ÿ During the movement, the contemporary employment of at least one safety sensor side and a sensor safety Ÿ compartment passage controls the stop of the door. K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 56: Self Restore Management Of Errors F-G-H-I-J
If the doors are smashed until the automation mode is closed and subsequently repositioned does not run no movement reset. For proper operation of the automated system with panic mounted photocells TOPP F3. 5.11 SELF RESTORE MANAGEMENT AFTER OPENING FIRE OR AN OPENING OF EMERGENCY The opening of emergency or fire causes the immediate opening of the automation, but in case where the sensors... -
Page 57: Digital Switch
This allows you to decrease the value of the function selected and return to the previous menu This allows you to scroll the menu downward. Hold for 4 sec to enter the menu K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 58: Maintenance
In order for the automation unit to operate correctly, the user shall be carried out periodical maintenance on the same. This maintenance activity may be carried out either by TOPP, in accordance with a specific agreement made with the user, or by the installation technician or by other competent and qualified technical personnel in possession of all legal requirements. -
Page 59: Demolition
Check the radar contacts, electromechanical block, switch not open contacts The door does not function and the display of Check the malfunction signal consulting the list of messages and the control circuit shows symbols or letters alarms K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE... -
Page 60: 7- Ec Declaration Of Incorporation Of Partly Completed Machinery
36066 Sandrigo (VI) Italia herewith declares that the person authorised to compile the technical file is Name: Plaza Trinidad - Topp S.r.l. Address: via Galvani,59 36066 Sandrigo (VI) and that to the partly completed machinery ELECTROMECHANICAL AUTOMATION FOR LINEAR SLIDING... - Page 61 K200T -K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 62 EN K200T-K280T INSTRUCTIONS FOR INSTALLATION AND USE...
- Page 64 TOPP S.r.l. Società a Socio Unico soggetta a direzione e coordinamento di 2 Plus 3 Holding S.p.a. Via Galvani, 59 - 36066 Sandrigo (VI) - Italia Tel. +39 0444 656700 - Fax +39 0444 656701 Info@topp.it - www.topp.it...
Need help?
Do you have a question about the K200T and is the answer not in the manual?
Questions and answers