Related Manuals for Siemens SINAMICS DCM 6RN
Summary of Contents for Siemens SINAMICS DCM 6RN
- Page 1 Tests carried out on drives This documentation pertains to SINAMICS DCM Reference Manual Excitation Unit SINAMICS DCM Type 6RN Edition 02/2019 www.siemens.com/drives...
- Page 2 14.02.2019 15:27 V8.00...
- Page 3 Introduction General scope of services Tests Excitation Unit SINAMICS DCM Type 6RN Reference Manual This documentation pertains to SINAMICS DCM Edition 02/2019...
-
Page 4: Edition
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. -
Page 5: Table Of Contents
Dimensions ..........................18 Function test...........................20 3.2.1 Connecting the excitation equipment ..................20 3.2.2 Voltage test ..........................20 3.2.3 Current limitation test ......................21 3.2.4 External EMERGENCY OFF....................21 3.2.5 Temperature monitoring of the de-excitation resistor.............22 Index................................23 SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... - Page 6 Table of contents SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM...
-
Page 7: Introduction
● Routine tests ● Tests that are offered as standard Note If the scope of testing and inspection cannot fulfill all customer requirements, please consult your Siemens sales advisor at head office. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... - Page 8 Introduction SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM...
-
Page 9: General Scope Of Services
4. Discussion of the test results 5. Preparation of test documentation for the customer. The test documentation is created before or after the customer leaves depending on the scope of testing and the time schedule. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... - Page 10 PD LD scope of supply. This also applies to components ordered from other Siemens' Groups. The technical data for these components is required at the latest eight weeks before the start of the acceptance test, e.g.: ●...
-
Page 11: Routine Test
General scope of services 2.1 Routine test Routine test During production, the drive is subject to an internal routine test. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 12: Visual Inspection
● Housing degree of protection ● Electrical cabinet components ● Cable installation ● Cable markings ● Setting values of circuit breakers, if used ● Dimensions See also Visual inspection (Page 16) SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 13: Function Tests
Siemens directives within the scope of quality assurance. The function tests are performed and documented in the Siemens test field by internal test field personnel. For the function test, the drive is in the test mode with restricted monitoring functions. -
Page 14: Insulation Test
The successful test is confirmed in a 3.1 certificate – or in the case that the customer has ordered the acceptance test, in a 3.2 certificate. The insulation test is performed on a separate acceptance day prior to the function test. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 15: Tests
Tests The tests that have been expressly ordered for the drive with serial number K91539032021001 are listed in the following. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 16: Visual Inspection
– Cooling slots – Fittings and rubber seals in the doors and between the cabinet units – Cable entries – Openings for water pipes, if available – Additional components, if available SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 17: Electrical Cabinet Components
– Are the cables routed according to the circuit diagram? Result The inspection is passed if the cable installation does not exhibit any deficiencies and matches the information in the circuit diagram. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 18: Cable Markings
The drive dimensions are measured. The basis for the visual inspection is the order-specific dimension drawing. Test procedure 1. The external dimensions, length, width and height of the drive are measured. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... - Page 19 Tests 3.1 Visual inspection Result The test is passed if the dimensions match with what is specified in the dimension drawing. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM...
-
Page 20: Function Test
Result The test is successfully passed if the characteristic of the armature current and voltage corresponds to the defined curve characteristics. The displays of calibrated measuring instruments serve as reference. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 21: Current Limitation Test
The excitation equipment displays "7.x" or 8.x (=" Ready to switch on"). The operating software displays "Ready to switch on". Result The test is successfully passed if the appropriate messages are displayed. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 22: Temperature Monitoring Of The De-Excitation Resistor
The excitation equipment displays "7.x" or 8.x (=" Ready to switch on"). The operating software displays "Ready to switch on". Result The test is successfully passed if the appropriate messages are displayed. SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... -
Page 23: Index
Visual inspection, 12, 16 Cable installation, 17 Cable markings, 18 Dimensions, 18 Electrical cabinet components, 17 Housing degree of protection, 16 Rating plate, 16 Setting values of circuit breakers, if used, 18 SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM... - Page 24 Index SINAMICS DCM 6RN F03 Reference Manual Rev.201902141527 SINAMICS DCM...
- Page 26 8888888888 000088 01 EN 01 Further Information www.siemens.com/drives Siemens AG Process Industries and Drives Postfach 48 48 90026 NÜRNBERG GERMANY *888888888800008801EN01* 888888888800008801EN01...
- Page 27 Process Industries and Drives Department PD LD P MF-NMA EN Siemens AG, PD LD P MF-NMA EN, Postfach 47 43, 90025 Nürnberg Tel. +49 (911) 433-6422 +49 (911) 433-6921 Email motoren.doku.aud@internal.siemens.co Our ref. 8888888888000088 Date 14.02.2019 Documentation for 6RN Your order no. - 000010...
- Page 29 Spine label for binder 50 mm (120 g/m2) SINAMICS DCM SINAMICS DCM Tests carried out on drives Spine label for binder 162 mm (120 g/m2) SINAMICS DCM 6RN SINAMICS DCM Tests carried out on drives...