Download
Share
Print this page
Topcon ASC-10 Programming Instructions Manual
  1. Manuals
  2. Brands
  3. Topcon Manuals
  4. Controller
  5. ASC-10
  6. Programming instructions manual

Topcon ASC-10 Programming Instructions Manual

Hide thumbs Also See for ASC-10:

Advertisement

Quick Links

See also: Operator's Manual
ASC-10
Programming Instructions
Part Number AGA4686
Rev 1.1
© Copyright Topcon Precision Agriculture
September, 2013
All contents in this manual are copyrighted by Topcon. All rights reserved. The information
contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published or
distributed, or otherwise reproduced without express written consent from Topcon.

Advertisement

loading
Need help?

Need help?

Do you have a question about the ASC-10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Topcon ASC-10

Summary of Contents for Topcon ASC-10

  • Page 1 © Copyright Topcon Precision Agriculture September, 2013 All contents in this manual are copyrighted by Topcon. All rights reserved. The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published or distributed, or otherwise reproduced without express written consent from Topcon.

  • Page 2: Table Of Contents

    ASC-10 Programming Instructions ASC-10 Programming Instructions Abstract This document contains the instructions for programming an ASC-10 ECU. Contents X30 System ..........................4 X20 System – Version numbers less than V2.2.2 ................ 5 X20 System – Version numbers from V2.2.2 ................8 System 150 –...
  • Page 3 ASC-10 Programming Instructions Version notice All revisions of this document are listed in chronological order. There is no relationship between the document number and the software release number. Document release Date Description V0.1 17/02/2011 Initial document V1.0 15/06/2011 Revision 1.0 V1.1...

  • Page 4: X30 System

    AGA4598 - HARNESS, ASC-10 CAN with Deutsch Termination  A3489 - HARNESS, ASC-10 Drive/Sense Each ASC-10 ECU is unique and requires installation via the New button and following the on-screen prompts. Entire system must be powered and comms must be present.

  • Page 5: Figure 2 - Starting P18Upg (Highlighted Icon)

    ASC-10 Programming Instructions X20 System – ASC-10 Version numbers less than V2.2.2 Programming ASC-10 in an X20 system can be performed with any version of the ASC-10 firmware. Entire system must be powered and comms must be present. 1. From the desktop, start the PIC18UPG program. See Figure 2 2.

  • Page 6: Figure 3 - Settings And Connected Message

    ASC-10 Programming Instructions Figure 3 - Settings and Connected message AGA4686 Rev 1.1 www.topconpa.com...

  • Page 7: Figure 4 - Programming Completed

    ASC-10 Programming Instructions Figure 4 - Programming completed AGA4686 Rev 1.1 www.topconpa.com...

  • Page 8: Figure 5 - Settings And Connected Message

    ASC-10 Programming Instructions X20 System – ASC-10 Version numbers from V2.2.2 Programming an ASC-10 in an X20 system can be performed with any version of the ASC- 10 firmware. Entire system must be powered and comms must be present. 1. From the desktop, start the PIC18UPG program. See Figure 2 2.
  • Page 9 System 150 – ASC-10 Version numbers less than V2.2.2 An ASC-10 in a System 150 cannot be programmed via a PCS150 console. 1. Remove the CAN comms cable from the ASC-10. Leave the main connector attached as this is required to supply power to the ASC-10.
  • Page 10 ASC-10 Programming Instructions System 150 – ASC-10 Version numbers from V2.2.2 An ASC-10 in a System 150 cannot be programmed via a PCS150 console. Programming can be performed using the following instructions or by connecting to an X30 system and following the instructions in Section 1 X30 System.
  • Page 11 13. Press the ‘Start Program’ button and wait. The RS232 and CAN LED’s flash alternatively at 0.5 Hz when the program has completed. The program takes approximately 6 seconds to complete. 14. Follow the instructions in Section 6 System 150 – ASC-10 Version numbers from V2.2.2 AGA4686 Rev 1.1...

  • Page 12: Figure 6 - Asc-10 Rs232 Programming Harness

    ASC-10 Programming Instructions System 150 – ASC-10 Version numbers from V2.2.2 from step 6 Figure 6 - ASC-10 RS232 Programming Harness AGA4686 Rev 1.1 www.topconpa.com...
  • Page 13 ASC-10 Programming Instructions System 150 – ASC-10 Version numbers from V2.2.2 An ASC-10 in a System 150 cannot be programmed via a PCS150 console. Programming can be performed using the following instructions or by connecting to an X30 system and following the instructions in Section 1 X30 System.