SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS! WARNING! Electrical shock hazard Particular attention shall be given to the relevant requirements regarding ventilation. Before carrying out any work on the electrical section of the appliance, it must Read these instructions carefully before installing be disconnected from the mains electricity this product.
Page 3
SAFETY AND WARNINGS the supply connection point (gas shut-off valve) is Packing elements (eg plastic bags, polystyrene accessible after installation. foam, staples, packing straps etc) and tools should the benchtop is made of a heat resistant material. not be left around during and after installation, the installation complies with all the requirements especially if they are within easy reach of children, of National and Local Authority Gas, Electric and...
PARTS SUPPLIED Wok stand (1) Foam tape (1) Fibre washers (1) Gas Elbow (1) Elbow “ BSP external thread (1) Clamping LPG test point brackets (4) adaptor (1) and screws (4) GAS RATE SUMMARY All appliances are factory set for LPG or Town Gas. SEMI-RAPID SEMI-RAPID SEMI-RAPID...
Page 5
GAS RATE SUMMARY HONG KONG BURNER SEMI-RAPID RAPID MINI WOK Nominal Nominal Nominal Nominal Nominal Jet size Jet size Jet size Jet size Jet size rating rating rating rating rating (mm) (mm) (mm) (mm) (mm) (kW) (kW) (kW) (kW) (kW) GAS TYPE 1.10 TG (G110)
Page 6
PRODUCT & CABINETRY DIMENSIONS Note: Gas inlet connection is located in the rear right corner. FRONT REAR SIDE Product and cabinetry dimensions (mm) overall height of product (excluding burners, dials and pan supports) overall width of product overall depth of product height of chassis (below top of bench) width of chassis...
CLEARANCE DIMENSIONS FRONT Clearance dimensions (mm) minimum clearance from left edge of cutout to nearest combustible surface minimum clearance from right edge of cutout to nearest combustible surface minimum clearance from rear edge of cutout to: nearest combustible surface nearest non-combustible surface minimum height of non-combustible material when used on adjacent walls minimum clearance from cooktop surface to: rangehood...
Page 8
DISCARD PACKAGING FIT THE ELBOW AND WASHER Model may vary from illustrations shown HONG KONG Foam T Foam Tape Elbow (1/2” BSP thread) & Washer Floating nut SINGAPORE Adhesive side Ensure edge of tape Adhesive side REAR CLAMPS FRONT CLAMPS lines up with outer 500 mm edge of cooktop...
LPG test point adaptor (if using LPG) FIT CLAMPING BRACKETS BASED ON THE SECURE TO BENCHTOP BENCHTOP THICKNESS Floating nut Fibre washer Elbow (½” BSP external thread) lifting o yellow tip good ame If converting to LPG, see 16 'Converting to a di erent gas type' LPG Models view from below Adjust to obtain a test point...
ALL Models Make sure the connection point will be accessible with the cooktop installed. AFFIX DUPLICATE DATA LABEL SOMEWHERE FIT PAN SUPPORTS To enable the gas supply to be readily shut o by the customer, make sure the connection ACCESSIBLE & PLUG COOKTOP IN is tted with an isolating valve close to the cooktop.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Installer’ s name: Have you installed the clamping brackets? Installer’ s signature: Have you verified that the type of model (factory-set for LPG or Installation company: Town Gas) matches the type of gas at the site of installation? Date of installation: Have you used the fibre washer supplied? Have you leak-tested all connections?
Page 12
安裝說明書 氣體煮食爐 CG604DX1型和CG905DX1型 HK SG 590633B 11.14...
Page 19
處置包裝材料 安裝彎頭和墊圈 你購買的型號可能與圖中所示的型號有差異 香港 Foam T Foam Tape 彎頭(1/2" BSP螺紋)和墊圈 浮動螺母 新加坡 Adhesive side Ensure edge of tape Adhesive side REAR CLAMPS FRONT CLAMPS lines up with outer 500 mm edge of cooktop Ensure edge of tape 採用負責任的方式回收利用 50 mm lines up with outer edge of cooktop 彎頭(1/2"...
Page 20
LPG test point adaptor (if using LPG) 根據檯面厚度安裝固定支架 固定在檯面上 Floating nut Fibre washer Elbow (½” BSP external thread) lifting o yellow tip good ame If converting to LPG, see 16 'Converting to a di erent gas type' LPG Models 從下面往上看 Adjust to obtain a test point Make sure the supply pressure Make sure to t the supplied...
Page 21
ALL Models Make sure the connection point will be accessible with the cooktop installed. 在看得見的地方貼上備用資料標籤並插好氣體煮 安裝平底鍋架 To enable the gas supply to be readily shut o by the customer, make sure the connection is tted with an isolating valve close to the cooktop. 食爐電源插頭...