Hkpf-525V - Sony MK7807V1 Manual Book

Interface Processor D Series

HKPF-525V

The HKPF-525 HD downconverter board converts a HD
component serial digital video signal to a SD component
serial digital signal and distributes it to four outputs. The
525-line component output signal format is selectable to
4:2:2 Y/B-Y/R-Y, 4:4:4 Y/B-Y/R-Y or 4:4:4 GBR. In the
case of 4:4:4 format signals, only two outputs are
available.
Features
* Downconverts an HD serial digital video signal to a SD
component serial digital signal * Support 1080 (1035) i to
485i at 59.94 Hz and 1080i to 576i at 50 Hz conversion *
Output signal aspect ratio selectable: squeeze, edge crop,
semi letter box (13:9, 14:9) and letter box (16:9) *
Minimum delay/frame delay selectable * Remote control
from HKDV-503 digital video controller * Parallel alarm
output
The HKPF Series function boards install in the PFV-HD Series Interface Units
together with the BKPF Series function boards.
Applicable Models
PFV-HD50A HD Digital Video Interface Unit
Specifications
Inputs/outputs
Digital video signal input:
DIGITAL IN connector (BNC type) (1)
HD component serial digital video
signal conforming to SMPTE292M, 1.5
Gb/s (BTA S-004B)
Input impedance:
75 Ω, unbalanced
Input return loss:
15 dB minimum (5 to 750 MHz)
15 dB minimum (750 MHz to 1.5 GHz)
Cable length:
100 m max. (When using a 5C-FB
coaxial cable)
Data rate:
1.4835 GHz/1.485 GHz
Remote control signals:
REMOTE IN connector (D-sub 9-pin) (1)
RS-422
Digital video outputs:
DIGITAL OUT 1, 2, 3, and 4 (BNC type)
(1 each)
525/625-line component serial digital
video signal
(switchable between Y/PB /PR and
GBR)
Supported formats (selectable):
525/625 4:2:2 Y/B-Y/R-Y
component serial digital video
525/625 4:4:4 Y/B-Y/R-Y
component serial digital video
525/625 4:4:4 GBR component serial
digital video
Three selectable modes (squeeze, edge
crop, and letter box)
Adjustable delay range:
Minimum Delay Mode
525:42 H -1~+100 H
625: 50 H -1~+100 H
Frame Delay Mode
525: 525 H 5 H
625: 625 H 5 H
HD-SD downconverter board
Adjustable parameters:
Detail gain, detail frequency,
level depend., crispness, H/V ratio, limit
level, gamma
General
Power supply:
+5.0 V DC: 2.0 A, -5.0 V DC: 1.0 A
(Supplied from the PFV-HD300A/HD50A
Interface Unit)
Power consumption:
Approx. 15 W
Operating temperature:
5 to 40 °C (41 to 104 °F)
Dimensions:
Board (H x W):
194 x 310 mm
(7 3/4 x 12 1/4 inches)
Connector panel (H x D x W):
218 x 98 x 25 mm
(8 5/8 x 3 7/8 x 1 inches)
Mass
Board:
Approx. 1500 g (1 lb 8 oz)
Connector panel:
Approx. 200 g (7 oz)
109
Rear Panel
D/A
HD SDI IN
REF IN
CLK
LOOP-THROUGH
RS-422
REMOTE IN
IN CASE OF 4:4:4
HKDV-503
Video Controller
1
2
SDI OUT
3
4
LINK A
LINK B